Design, Construction, and Performance Analysis of a Wood Thermal Conductivity Measurement Device using Flat Plate Heat Pipes by Rasouli Moien, Mohammad Layeghi, Saber Lotfi

Get full text

Inverse boundary problem in estimating heat transfer coefficient of a round pulsating bubbly jet: design of experiment by Honeyeh Razzaghi, Farshad Kowsary, Mohammad Layeghi

Get full text

Drying Kinetics of Poplar (Populus Deltoides) Wood Particles by a Convective Thin Layer Dryer by Hamid Zarea Hosseinabadi, Kazem Doosthoseini, Mohammad Layeghi

Get full text

Minimizing hot-press time in the manufacturing process of wood plastic composites by Nazanin Motie, Ghanbar Ebrahimi, Mehdi Tajvidi, Mohammad Layeghi

Get full text

Prediction of bending moment resistance of screw connected joints in plywood members using regression models and compare with that commercial medium density fiberboard (MDF) and pa... by Sadegh Maleki, Mehdi Faezipour, Ghanbar Ebrahimi, Mohammad Layeghi

Get full text

Investigation on the effect of wooden dowel diameter, penetration depth and species on the bending moment resistance under diagonal tensile load of corner joints in case-type furni... by Mosayeb Dalvand, Ghanbar Ebrahimi, Mehdi Tajvidi, Mohammad Layeghi

Get full text

The effect of layer’s moisture content and pre-heating by microwave radiation on physical and mechanical properties of laminated veneer lumber by Mohammad Farajallahpour, mohammad layeghi, kazem Dosthosseini, hanidreza edalat

Get full text

Effect of Graphite powder on thermal conductivity, physical and mechanical properties of 3-layer particleboard by Amin Malekani, Kazem Dousthosseini, Mehdi Faezipour, Mohammad Layeghi

Get full text

Study of Stress Capacity Improvement of L-type Joint by Chemical Modification of Wood by Hamideh Abdolzadeh, Mohammad Layeghi, Ghanbar Ebrahimi, Mehdi Ghassemie

Get full text

The predicting ultimate of joint withdrawal resistance constructed of plywood with regression models application according to diameter and penetrating depth by Sadegh Maleki, Mahdi Faezipour, Ghanbar Ebrahimi, Mohammad Layeghi

Get full text

Investigation on bending moment resistance of L- shaped screwed corner joints constructed of Plywood members by Sadegh Maleki, Mohammad Mehdei Faezipour, Ghanbar Ebrahimi, mohammad Layeghi

Get full text

Evaluation of elevated temperature influence on mechanical properties of a commercial unrefined bagasse fiber-polypropylene composite by Foroogh Dastoorian, Mohammad Layeghi, Ghanbar Ebrahimi, Mahdi Tajvidi, Majid Zabihzadeh

Get full text

Evaluation of the refining effects on the properties of transparent paper produced from bagasse fiber by farzaneh shiralizadeh, mohammad azadfallah, ali Abdolkhani, mohammad Layeghi, saeed mahdavi

Get full text

Prediction mechanical properties of particleboard and analysis the interaction effect of slenderness ratio and resin content, using linear, quadratic and exponential equation by Mohammad Arabi, Mohammad mehdi Faezipoor, Mohammad Layeghi, Ali akbar Enayati

Get full text

Mechanical properties of Beech -Furfuryl alcohol wood polymer by Hamideh Abdolzadeh, Ghanbar Ebrahimi, Mohammad Layeghi, Mahdi Ghasemieh, Ahmad Mirshokrai

Get full text

Evaluation of bending performance for cross laminated timber (CLT) made out of poplar (Populus alba) by akbar Rostampour Haftkhani1, mohammad layeghi, ghanbar ebrahimi, kambiz Pourtahmasi

Get full text

Fracture Behavior of Beech-Furan Wood Polymer under Mode I by Hamideh Abdolzadeh, Ghanbar Ebrahimi, Mohammad Layeghi, Mehdi Ghasemieh, Seiad Ahmad Mirshokraei

Get full text

Effects of fastener type, end distance, layer arrangement, and panel strength direction on lateral resistance of single shear lap joints in cross-laminated timber (CLT) by Farshid Abdoli, Maria Rashidi, Akbar Rostampour-Haftkhani, Mohammad Layeghi, Ghanbar Ebrahimi

Get full text

Creep rupture behavior of a bagasse fiber-polypropylene composite by foroogh dastoorian, Mohammad Layeghi, Ghanbar Ebrahimi, Mehdi Tajvidi, Seid Majid Zabihzadeh

Get full text

Withdrawal Performance of Nails and Screws in Cross-Laminated Timber (CLT) Made of Poplar (<i>Populus alba</i>) and Fir (<i>Abies alba</i>) by Farshid Abdoli, Maria Rashidi, Akbar Rostampour-Haftkhani, Mohammad Layeghi, Ghanbar Ebrahimi

Get full text