Straight-sided splines for cylindrical shafts : metric nominal dimensions, tolerances and gauging requirements

Straight-sided splines for cylindrical shafts : metric nominal dimensions, tolerances and gauging requirements

PSZJBL

Bibliographic Details
Main Author:	8096 British Standards Institution
Format:
Subjects:	Shafts (Excavations)

Similar Items

Dimensions of taper shaft ends
by: 8096 British Standards Institution

Straight cylindrical involute splines : metric module, side fit
by: 8096 British Standards Institution, et al.
Published: (1981)

Drilled shafts in rock : analysis and design /
by: 346196 Zhang, Lianyang
Published: (2004)

Guide to the selection of fitment bores for cylindrical shaft ends
by: 8096 British Standards Institution

Shaft ends
by: 8096 British Standards Institution

Shaft centre heights
by: 8096 British Standards Institution

Rotary shaft lip seals
by: 8096 British Standards Institution

Measurements and evaluation of vibration on rotating shafts
by: 8096 British Standards Institution
Published: (1986)

Dimensions of power take-off driving shafts and mounting faces for small internal combustion engines
by: 8096 British Standards Institution

Straight-sided splines and serrations
by: 8096 British Standards Institution

Involute splines : metric module, side fit
by: 8096 British Standards Institution
Published: (1981)

Shaft generators (1959-1974)
by: British Ship Research Association
Published: (1974)

Design of transmission shafting
by: 11585 American National Standards Institute, et al.

Forging ahead in the power generation.
by: Evans, Albert, author
Published: (1998)

EXPERIMENTAL AND NUMERICAL STRESS ANALYSIS OF INVOLUTE SPLINED SHAFT
by: Majid H. Faidh-Allah, et al.
Published: (2023-07-01)

Numerical investigation on arching effect surrounding deep cylindrical shaft during excavation process
by: Tanawat Tangjarusritaratorn, et al.
Published: (2022-10-01)

Reserves for improving the design of shafts
by: Valeriy V Kirilovskiy
Published: (2018-12-01)

Shafting system dynamics
by: British Ship Research Association
Published: ([19-)

Permanent Shaft Repair Technology for Damaged Shield Segments in Operating Metro Tunnels
by: Fengyu LIAN, et al.
Published: (2024-01-01)

Dimensions of cylindrical shaft ends and hubs for alternators for commercial vehicles and buses
by: 8096 British Standards Institution

Shaft alignment : hull deflections (1969-1973)
by: 342145 Kahler, R. C., et al.
Published: (1974)

FIXTURING DEVICE FOR DRILLING A STRAIGHT SHAFT
by: SUSAC, Florin, et al.
Published: (2017-05-01)

FIXTURING DEVICE FOR DRILLING A STRAIGHT SHAFT
by: Florin Susac, et al.
Published: (2017-05-01)

FIXTURING DEVICE FOR DRILLING A STRAIGHT SHAFT
by: Florin Susac, et al.
Published: (2017-05-01)

Virtual Simulations of a New Construction of the Artificial Shaft Bottom (Shaft Safety Platform) for Use in Mine Shafts
by: Paweł Kamiński, et al.
Published: (2021-04-01)

Shaft alignment 1968-1970
by: British Ship Research Association
Published: (1971)

Shaft alignment 1966-1974
by: British Ship Research Association
Published: (1971)

Fracture cause analysis of the extruder’s shaft and geometry optimization of the spline
by: O. Lyashuk, et al.
Published: (2019-03-01)

Modeling the Pumping Behavior of Macroscopic Lead Structures on Shaft Counterfaces of Rotary Shaft Seals
by: Maximilian Engelfried, et al.
Published: (2023-11-01)

Shaft vibration, 1964-1979
by: British Ship Research Association
Published: ([19-)

Progress in studies on key technologies for marine propulsion shafting scheme design
by: Lai Guojun, et al.
Published: (2019-10-01)

Shaft alignment handbook /
by: Piotrowski, John, 1952-
Published: (2007)

Shaft alignment handbook /
by: 176695 Piotrowski, John
Published: (1995)

Shaft Alignment Handbook /
by: Piotrowski, John, author 176695
Published: (1986)

Estimating the severity of synchronous and subsynchronous shaft vibration within fluid-film journal bearings /
by: 220708 McHugh, James D.

Access to Deposits as a Stage of Mining Works
by: Krzysztof Skrzypkowski, et al.
Published: (2022-11-01)

Influence of Hydrogeological Investigation’s Accuracy on Technology of Shaft Sinking and Design of Shaft Lining—Case Study from Southern Poland
by: Kajetan d’Obyrn, et al.
Published: (2021-04-01)

Shaft alignment programme [disket] /
by: 412175 Lee, James Hien Hon
Published: (1990)

Metric gauge blocks
by: 8096 British Standards Institution

Numerical Simulation of Deformation and Failure Mechanism of Main Inclined Shaft in Yuxi Coal Mine, China
by: Fan Wu, et al.
Published: (2022-05-01)