Design and fabrication of cutting-tool force dynamometer/

Design and fabrication of cutting-tool force dynamometer/

Thesis (Bachelor in Mechanical Engineering) - Universiti Teknologi Malaysia, 1980

Bibliographic Details
Main Author:	270561 Sahani Ahmad
Format:
Published:	Kuala Lumpur : UTM, 1980
Subjects:	Dynamometer Cutting

Similar Items

Stability Evaluation for a Damped, Constrained-Motion Cutting Force Dynamometer
by: Michael Gomez, et al.
Published: (2022-02-01)

Measurement of Wood Cutting Forces during Bandsawing Using Piezoelectric Dynamometer
by: Payam Moradpour, et al.
Published: (2016-03-01)

Design, fabricate and testing small dynamometer for wind turbine /
by: Mohd. Azri Mohd. Nor, 1986-, et al.
Published: (2009)

Design and construction of a strain gauge-based dynamometer for a 3-axis cutting force measurement in turning process
by: M. Rizal, et al.
Published: (2018-12-01)

Development of spinning tool dynamometer /
by: 266456 Goh, Teck Chai
Published: (1999)

Development of specifications for a motorcycle dynamometer and motorcycle cooling system/
by: 447339 Herling, Robert J.
Published: (1976)

Development of specifications for a motorcycle dynamometer and motorcycle cooling system/
by: 447339 Herling, Robert J.
Published: (1976)

Design, fabricate and testing small dynamometer for wind turbine [electronic resource] /
by: Mohd. Azri Mohd. Nor, 1986-
Published: (2009)

Sistem kawalan dynamometer froude /
by: 398403 Muhamad Ridzhuan Othman
Published: (2000)

Design and calibration of a six component dynamometer used in an aerodynamic tunnel
by: Liviu Crudu, et al.
Published: (2022-12-01)

Development of a motorcycle chassis dynamometer /
by: Nik Mohd. Arif Nik Yahya, 1985-, et al.
Published: (2008)

A study on a two dimensional dynamometer for surface grinding /
by: 448675 Ito, Shoji

Design, development, calibration, and testing of indigenously developed strain gauge based dynamometer for cutting force measurement in the milling process
by: T. Mohanraj, et al.
Published: (2020-06-01)

Design of eddy current dynamometer controller /
by: 405412 Muhamad Fazil Mat Yusop, et al.
Published: (2003)

Upgraded Kalman Filtering of Cutting Forces in Milling
by: Giovanni Totis, et al.
Published: (2020-09-01)

A dynamometer on which the dynamic behavior of a passenger car can be simulated /
by: 428430 Odier, Jean

Development and Testing of a High-Frequency Dynamometer for High-Speed Milling Process
by: Yanlin Lyu, et al.
Published: (2021-01-01)

Development of a motorcycle chassis dynamometer [electronic resource] /
by: Nik Mohd. Arif Nik Yahya, 1985-
Published: (2008)

Fibrous material friction behavior of prony brake dynamometer /
by: Augeny Satik Ayak, 1994- 611687, et al.
Published: (2017)

Fibrous material friction behavior of prony brake dynamometer /
by: Augeny Satik Ayak, 1994- 611687
Published: (2017)

Dynamometer tests of the efficiency of a van transmission systems /
by: 401368 Williams, T., et al.
Published: (1985)

Design of eddy current dynamometer controller [electronic resource] /
by: 405412 Muhamad Fazil Mat Yusop, et al.
Published: (2003)

Design and Development of a Tri-Axial Turning Dynamometer Utilizing Cross-Beam Type Force Transducer for Fine-Turning Cutting Force Measurement
by: Muhammad Rizal, et al.
Published: (2022-11-01)

Design, fabrication, and evaluation of a wireless pull-type dynamometer
by: I Ahmadi
Published: (2016-09-01)

Kajian pemantauan kegagalan mata alat menggunakan alat dinamometer daya pemotongan dan pancaran akustik /
by: 211704 Rohani Rahmad
Published: (2002)

Problems of dynamometer construction for wheelchairs and simulation of push motion
by: Wieczorek Bartosz, et al.
Published: (2019-01-01)

Experimental Comparison of Hub- and Roller-Type Chassis Dynamometers for Vehicle Exhaust Emissions
by: Barouch Giechaskiel, et al.
Published: (2022-03-01)

A Smart Tool Holder Calibrated by Machine Learning for Measuring Cutting Force in Fine Turning and Its Application to the Specific Cutting Force of Low Carbon Steel S15C
by: Liang-Wei Tseng, et al.
Published: (2021-09-01)

The development of a high speed dynamometer and preliminary results obtained from a C A V O1 turbine / [mikrofis]
by: 344895 Adgey J. M.
Published: (1969)

Applicability of hydraulic dynamometer for measuring load mass on forwarders
by: Pandur Zdravko, et al.
Published: (2015-01-01)

Sharinkage stresses in polyester-metal joints; A comparative study of three, four and five speed automobile transmissions : technical and economical; Design and fabrication of cutting-tool force dynamometer; Investigation chatter on a vertical drilling machine; The design and construction of a double pipe heat exchanger; Design and fabrication of a Go-Kart; Testing and modification of balancing machine; Comparative studies on the designs and general costings of pressure vessels [microform] /
by: Mohd. Ridzuan Ismail, et al.
Published: (1977)

Portable Dynamometer-Based Measurement of Pelvic Floor Muscle Force
by: Batoul El-Sayegh, et al.
Published: (2023-01-01)

Considerations for Achieving Equivalence between Hub- and Roller-Type Dynamometers for Vehicle Exhaust Emissions
by: Christian Engström, et al.
Published: (2022-10-01)

Impact of Circular Saw Blade Design on Forces During Cross-Cutting of Wood
by: Zdeněk Kopecký, et al.
Published: (2022-01-01)

Analisis prestasi mesin mobil diesel turbocharger yang diuji dengan dynamometer
by: Yusvardi Yusuf, et al.
Published: (2019-11-01)

Place of the gold standard isokinetic dynamometer in Paralympic sports: a systematic review
by: Shirko Ahmadi, et al.
Published: (2021-02-01)

Design of a Chassis Dynamometer Facility for the European Type-Approval of Passenger Cars Manufactured in Pakistan
by: Kashif Usman, et al.
Published: (2023-09-01)

Surgical Dynamometer to Simultaneously Measure the Tension Forces and the Distance between Wound Edges during the Closure of a Laparotomy
by: Joan Roca, et al.
Published: (2018-01-01)

Analysis of braking parameters in testing of brake wear and particles formation on inertial brake dynamometer
by: Vasiljević Saša Ž., et al.
Published: (2022-01-01)

Design, Construction and Test of a Three-point Hitch Dynamometer
by: M Askari, et al.
Published: (2011-09-01)