Determine optimum parameter of plastic injection molding using cae simulation and design of experiment (DOE) [electronic resource] /

Determine optimum parameter of plastic injection molding using cae simulation and design of experiment (DOE) [electronic resource] /

Project Paper (Sarjana Muda Kejuruteraan (Mekanikal - Pembuatan)) - Universiti Teknologi Malaysia, 2008

Bibliographic Details
Main Author:	Fairullizam Isahak, 1985-
Format:
Language:	eng
Published:	2008
Subjects:	Injection molding of plastics Plastics

Similar Items

Determine optimum parameter of plastic injection molding using cae simulation and design of experiment (DOE) /
by: Fairullizam Isahak, 1985-, et al.
Published: (2008)

CAE : computer aided engineering for injection molding/
by: Bernhardt, Ernest C.
Published: (1983)

Plastics Injection Molding : Scientific Molding, Recommendations, and Best Practices /
by: Valero, José R. Lerma, author 651639, et al.
Published: (2020)

Simulation of plastic injection of molding electrical appliances /
by: Nadiah Rahmat, 1986-, et al.
Published: (2009)

Gastrow injection molds : 130 proven designs
by: 360320 Gastrow, Hans, et al.
Published: (c200)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment /
by: Muhamad Al Baraq Isharudin, 1987-, et al.
Published: (2010)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
by: Low, Thuan Himm, 1986-, et al.
Published: (2010)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
by: Low, Thuan Himm, 1986-
Published: (2010)

Injection/transfer molding of thermosetting plastics /
by: 302512 Wright, Ralph E.
Published: (1995)

Investigations an effect of sink mark problem on plastic product by process of plastic injection molding /
by: 405779 Nur Aisyah Aimi Abd. Rahman, et al.
Published: (2009)

Simulation of plastic injection of molding electrical appliances [electronic resource] /
by: Nadiah Rahmat, 1986-
Published: (2009)

Injection molds and molding :
by: 179539 Dym, Joseph B.
Published: (1987)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment [electronic resource] /
by: Muhamad Al Baraq Isharudin, 1987-
Published: (2010)

Molding of plastics /
by: Bikales, Norbert M.
Published: (1971)

Simulation of plastic injection molding of accessories automotive part using plastic flow analysis software and the Taguchi method /
by: Zaim@Abdul Yamin Mahdi, 1987-, et al.
Published: (2010)

Design of experiment spreadsheet for injection molding process optimization /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Injection molding [kasetvideo]
Published: (1985)

Design and optimization of runner system in plastics injection molding for multi - cavity product /
by: Nur Raihana Sukri, 1985-, et al.
Published: (2009)

Investigations an effect of sink mark problem on plastic product by process of plastic injection molding [electronic resource] /
by: 405779 Nur Aisyah Aimi Abd. Rahman, et al.
Published: (2009)

Selecting injection molds : weighing cost versus productivity /
by: Rees, Herbert, 1915-, et al.
Published: (2006)

An optimization of the plastic injection molding parameters for sport equipment by using doe methods /
by: Radhwan Hussin, et al.
Published: (2013)

Simulation of plastic injection moulding of a computer part using moldex software and design of experiment (DOE) /
by: Remnesh Kumar Rajasekaran, 1986-, et al.
Published: (2010)

Design and optimization of runner system in plastics injection molding for multi - cavity product [electronic resource] /
by: Nur Raihana Sukri, 1985-
Published: (2009)

Simulation of plastic injection molding of accessories automotive part using plastic flow analysis software and the Taguchi method [electronic resource] /
by: Zaim@Abdul Yamin Mahdi, 1987-
Published: (2010)

Injection and compression molding fundamentals/
by: Isayev, Avraam I.
Published: (1987)

Effect of injection molding parameters to the quality of a standard molded part by using CAE software (Moldex3D) /
by: Mohamed Faiz Mohamed Shah, 1985, et al.
Published: (2009)

Investigation of optimum gate location in plastic injection moulding of automotive part using moldflow and doe method /
by: Ngu, Heng Chung, 1995- 625397, et al.
Published: (2019)

Investigation of optimum gate location in plastic injection moulding of automotive part using moldflow and doe method /
by: Ngu, Heng Chung, 1995- 625397
Published: (2019)

Simulation of plastic injection moulding of a car door-handle trim using moldex and design of experiment (DOE) /
by: 389833 Ngu, Ying Kui, et al.
Published: (2008)

A development of computerized FMEA database for plastic injection molding process /
by: Mohamad Rusydi Shukor, 1988-, et al.
Published: (2012)

Design of experiment spreadsheet for injection molding process optimization [electronic resource] /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Simulation and optimized analysis of cooling channels of injection molding for food container based autodesk moldflow and design of experiment (DOE) /
by: Khor, Chin Keat, 1989-, et al.
Published: (2015)

Spotting the key variables in the plastic injection molding process by using shainin's variables search design /
by: 279849 Mohd. Firdauz Jamaluddin
Published: (2003)

Process improvement in injection molding using design of experiment /
by: Mohd. Erric Mohammad, 1984-, et al.
Published: (2008)

Injection molds : 108 proven designs /
by: 360320 Gastrow, Hans, et al.
Published: (1993)

RIM : fundamentals of reaction injection molding/
by: 345476 Macosko, Christopher W.
Published: (1989)

Injection molding handbook/
by: Rosato, Dominick V., et al.
Published: (1986)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (c200)

Reaction injection molding/
by: Becker, Walter E.
Published: (1979)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (2002)