Quality improvement for injection moulding process by using design of experiment /

Quality improvement for injection moulding process by using design of experiment /

Project Paper (Sarjana Muda Kejuruteraan (Mekanikal - Pembuatan)) - Universiti Teknologi Malaysia, 2012

Detalhes bibliográficos
Principais autores:	Ahmad Aliff Che Aziz, 1987, Muhamad Zaman Mat Saman, supervisor, Fakulti Kejuruteraan Mekanikal
Formato:
Idioma:	eng
Publicado em:	2012
Assuntos:	Molding materials

Registros relacionados

Quality improvement for injection moulding process by using design of experiment [electronic resources] /
por: Ahmad Aliff Che Aziz, 1987, et al.
Publicado em: (2012)

Quality improvement in injection moulding company by using experimental design approach /
por: Muhammad Azzuan Mat Reffien, 1986-, et al.
Publicado em: (2009)

Investigation of injection moulding process parameters of green biodegradable polymer compound using moldflow software and design of experiment /
por: Chong, Wei Lun, 1988-, et al.
Publicado em: (2012)

Investigation of injection moulding process parameters of green biodegradable polymer compound using moldflow software and design of experiment [electronic resources] /
por: Chong, Wei Lun, 1988-, et al.
Publicado em: (2012)

Six sigma methodology implementation in injection molding process /
por: Ayu Artini Alif Lee, 1989-, et al.
Publicado em: (2012)

Design and fabrication multi cavities injection mould /
por: 268392 Gan, Yew Ting
Publicado em: (1996)

Quality improvement for injection moulding mechine in a manufacturing company /
por: Khairul Hafizi Sulaiman, 1988-, et al.
Publicado em: (2011)

Simulation of plastic injection moulding of family mould using moldflow and design of experiment /
por: Mohd. Najib Mohd. Badri, 1978-, et al.
Publicado em: (2010)

Investigate of parameter setting on injection moulding part using simulation of moldflow and design of experiment /
por: Norfaezah Latiff, 1988-, author, et al.
Publicado em: (2012)

Quality improvement in injection moulding company by using experimental design approach [electronic respurce] /
por: Muhammad Azzuan Mat Reffien, et al.
Publicado em: (2009)

Design and fabrication of the resin transfer moulding mould /
por: 300709 Ooi, Yean Chyan
Publicado em: (1997)

Investigate of parameter setting on injection moulding part using simulation of moldflow and design of experiment [electronic resource] /
por: Norfaezah Latiff, 1988-, author, et al.
Publicado em: (2012)

Simulation of plastic injection moulding part using moldflow and design of experiment /
por: Shamsul Azwan Halim, 1975-, et al.
Publicado em: (2010)

Advances in injection moulding /
por: 326458 Maier, C. A.
Publicado em: (1992)

Injection moulding technology

Quality improvement in an injection moulding company using six sigma methodology /
por: 238668 Thanaraj Sanmugham, et al.
Publicado em: (2008)

Thermoplastics injection mouldings
por: 8096 British Standards Institution
Publicado em: (1993)

Design and optimization of runner system in plastic injection moulding for multy-cavity products by using moldex and design of experiment/
por: Syarizal Iqbal Baba, 1987-, et al.
Publicado em: (2010)

Development of a plastic injection mould /
por: 312716 Lim, Seng Giam, et al.
Publicado em: (1994)

Quality improvement in an injection moulding company by using process failure mode effect analysis (PFMEA) /
por: Jafri Mohd. Rohani, et al.

Assessment of warpage and shrinkage in injection moulding process /
por: Fitriyanti Arsyad, 1991-, author, et al.
Publicado em: (2017)

Assessment of warpage and shrinkage in injection moulding process /
por: Fitriyanti Arsyad, 1991-, author, et al.
Publicado em: (2017)

Effect on adhesion quality of hydroxyapatite on investment casting mould /
por: Mohd. Zulhafiz Mohamad Zulkifli, 1985-, et al.
Publicado em: (2011)

Process improvement in injection molding using design of experiment /
por: Mohd. Erric Mohammad, 1984-, et al.
Publicado em: (2008)

Simulation of plastic injection moulding of an air guide using moldex software and the design of experiments /
por: Siti Azeah Mohd. Hashim, 1985-, et al.
Publicado em: (2008)

Simulation of plastic injection moulding part using moldflow and design of experiment [electronic resource] /
por: Shamsul Azwan Halim, 1975-, et al.
Publicado em: (2010)

Effect of injection moulding processing temperature to the mechanical and thermal properties of polycarbonate /
por: 455769 Teh, Boon Khai, et al.
Publicado em: (2007)

Resin transfer moulding (RTM) /
por: 204926 Shukur Abu Hassan, et al.

Quality impovement in injection moulding company using doe/
por: 427113 Ooi, Chee Keong, et al.
Publicado em: (2007)

Reclaimation of investment casting mould material /
por: 463819 Kartini Rahman, et al.
Publicado em: (2007)

Injection Moulds for Beginners /
por: Dangel, Rainer, author
Publicado em: (2016)

Injection moulding of rubber/
por: 257779 Wheelands, Michael Arthur
Publicado em: (1974)

Injection moulding materials /
por: 230831 Whelan, A.
Publicado em: (1982)

Injection moulds/
por: Welling, M. S.
Publicado em: (1980)

Parameter setting through optimization of variable cooling channels which effect to the injection moulding product quality /
por: Jasmi Mohd. Sa'at, 1969-, et al.
Publicado em: (2012)

Simulation plastic injection moulding of fishing reel side cover using moldex software and design of experiment /
por: Mohd. Ariff Abdul Rahman, 1986-, et al.
Publicado em: (2009)

Evaluation and treatment of moulding sand for green sand moulding process /
por: 212072 Norhaswani Kasim
Publicado em: (2006)

Plastics injection moulding in the 1990s
Publicado em: (1990)

Injection-mould design fundamentals/
por: 435411 Glanvill, A. B., et al.
Publicado em: (1965)

Hot runners in injection moulds /
por: 351687 Frenkler, Daniel, et al.
Publicado em: (2001)