The exit failure of cemented carbide face milling cutters part 1-fundamentals and phenomenae/

The exit failure of cemented carbide face milling cutters part 1-fundamentals and phenomenae/

PSZJBL

Bibliographic Details
Main Author:	549607 Pekelharing, A. J.
Format:
Language:	eng
Subjects:	Geometry face milling

Similar Items

Analysis of the influence of the location schemes of form-forming cutting elements on the deformation processes of step face milling cutters
by: H.M., et al.
Published: (2023-06-01)

Improving the finishing face milling process of flat surfaces of small width parts
by: H.M., et al.
Published: (2021-06-01)

Milling cutters and end mills
by: 11585 American National Standards Institute, et al.

Machinability of cast irons at finishing face milling of flat surfaces by superhard materials
by: S.I., et al.
Published: (2021-06-01)

Milling cutters
by: 8096 British Standards Institution

Ways of improving the process of machining the flat surfaces of parts by milling
by: O.A. Gromovyy, et al.
Published: (2020-12-01)

The influence of oblique geometry face mill on the cutting temperature during finishing and semi-finishing flat surface
by: M.M.
Published: (2022-12-01)

Experimental Analysis of Ductile Cutting Regime in Face Milling of Sintered Silicon Carbide
by: Marvin Groeb, et al.
Published: (2022-03-01)

Selected aspects of the design of special monolithic carbide milling cutters for austenitic steels
by: Małek Marcin, et al.
Published: (2023-01-01)

Effect of multi-arc ion plating process on coating performance of cemented carbide PCB milling cutter
by: Xiaofan YANG, et al.
Published: (2023-10-01)

Modeling and optimization of surface roughness and productivity thru RSM in face milling of AISI 1040 steel using coated carbide inserts
by: Mohamed Fnides, et al.
Published: (2017-03-01)

Experimental Investigation into Wear and Tool Life of Milling Cutter PVD Coated Carbide Inserts While Armox 500 Steel Hard Milling
by: Jozef Majerík, et al.
Published: (2018-01-01)

Milling Force Modeling Methods for Slot Milling Cutters
by: Mingzhou Wu, et al.
Published: (2023-09-01)

Experimental Investigation on the Effect of Different Micro-Geometries on Cutting Edge and Wiper Edge on Surface Roughness and Forces in Face Milling
by: Padmakumar Muthuswamy, et al.
Published: (2021-10-01)

The influence of mechanical properties of workpiece material on the main cutting force in face milling
by: M. Sekulić, et al.
Published: (2010-10-01)

KINEMATIC SCHEMES OF CUTTING IN MILLING
by: Evstati LEFTEROV, et al.
Published: (2018-05-01)

Modeling of machined surface roughness and optimization of cutting parameters in face milling
by: D. Bajić, et al.
Published: (2008-10-01)

Experimental Analysis of the Effect of Vibration Phenomena on Workpiece Topomorphy Due to Cutter Runout in End-Milling Process †
by: Constantine David, et al.
Published: (2018-07-01)

Structural Parameter Analysis and Machining Simulation of Vertical Milling Cutter
by: Zhou Xin, et al.
Published: (2019-04-01)

High-Performance Face Milling of 42CrMo4 Steel: Influence of Entering Angle on the Measured Surface Roughness, Cutting Force and Vibration Amplitude
by: Marcin Płodzień, et al.
Published: (2021-04-01)

INCREASING THE RESOURCE OF MILLING CUTTERS USED TO PROCESS THELOCOMOTIVE WHEELSETS. PART2: STUDYOFSTRESSED-DEFORMEDSTATE
by: Aleksander SŁADKOWSKI, et al.
Published: (2020-09-01)

Sustainability Assessment for Dry, Conventional and Cryogenic Machining in Face Milling of Ti-6Al-4V
by: IMRAN MASOOD, et al.
Published: (2017-04-01)

Experimental Investigation on Direct Micro Milling of Cemented Carbide
by: Xian Wu, et al.
Published: (2019-02-01)

Manufacturing Analysis of Face Milling Technology by Tool Setting Using the Same Initial Parameters
by: Bodzâs Sândor
Published: (2023-05-01)

Machinability of aluminium alloy when face milling using carbide inserts /
by: Mohd. Zamri Borhan, 1977-, et al.
Published: (2013)

Face milling of titanium alloys using coated and uncoated carbide tools /
by: 372470 Safian Sharif
Published: (1999)

Cycloid Approximation with Circle for the Calculation of Exit Angle
by: György Póka, et al.
Published: (2019-01-01)

Research on NC Machining Method of Face Gear in High Speed Milling
by: Xingzu Ming, et al.
Published: (2019-01-01)

The Use of Dredged Sediment from the Watsongpeenong Canal with Paper Mill Residue to Produce Facing Bricks
by: Jiraporn Namchan, et al.
Published: (2018-02-01)

The Use of Dredged Sediment from the Watsongpeenong Canal with Paper Mill Residue to Produce Facing Bricks
by: Jiraporn Namchan, et al.
Published: (2018-02-01)

The Use of Dredged Sediment from the Watsongpeenong Canal with Paper Mill Residue to Produce Facing Bricks
by: Jiraporn Namchan, et al.
Published: (2018-02-01)

The Use of Dredged Sediment from the Watsongpeenong Canal with Paper Mill Residue to Produce Facing Bricks
by: Jiraporn Namchan, et al.
Published: (2018-02-01)

New geometry and technology of face-gear forming with circle line of teeth on CNC milling machine
by: P. Frąckowiak, et al.
Published: (2012-01-01)

Effect of the Relative Position of the Face Milling Tool towards the Workpiece on Machined Surface Roughness and Milling Dynamics
by: Danil Yurievich Pimenov, et al.
Published: (2019-02-01)

Mathematical Models of the Geometry of Micro Milling Cutters
by: Isaev Alexander, et al.
Published: (2021-01-01)

Dynamics of cutting structural steels with end-milling cutters
by: A. N. Gavrilin, et al.
Published: (2009-06-01)

Dynamics of cutting structural steels with end-milling cutters
by: A. N. Gavrilin, et al.
Published: (2009-06-01)

CONSIDERATIONS REGARDING THE STRENGTH CALCULUS OF MILLING CUTTERS TEETH
by: Catălin ROŞU
Published: (2013-05-01)

Waviness at dry high-speed face milling of some hard steels
by: Irina Beşliu-Băncescu, et al.
Published: (2021-12-01)

Influence of the Cutting Strategy on the Temperature and Surface Flatness of the Workpiece in Face Milling
by: Lukasz Nowakowski, et al.
Published: (2020-10-01)