The effect of painting parameters on the mechanical properties of injection-molded abs polymer for engineering purpose /

The effect of painting parameters on the mechanical properties of injection-molded abs polymer for engineering purpose /

Show other versions (1)

Project Paper (Sarjana Muda Kejuruteraan (Mekanikal)) - Universiti Teknologi Malaysia, 2017

Bibliographic Details
Main Authors:	Muhammad Izrul Fahmi Mohamed Rusli, 1994- 611619, Muhamad Azizi Mat Yajid supervisor 209177, Fakulti Kejuruteraan Mekanikal 8081
Format:
Language:	eng
Published:	Johor Bahru, Johor : Universiti Teknologi Malaysia, 2017
Subjects:	Injection molding of plastics Plastic coating

Similar Items

The effect of painting parameters on the mechanical properties of injection-molded abs polymer for engineering purpose /
by: Muhammad Izrul Fahmi Mohamed Rusli, 1994- 611619
Published: (2017)

Gastrow injection molds : 130 proven designs
by: 360320 Gastrow, Hans, et al.
Published: (c200)

Selecting injection molds : weighing cost versus productivity /
by: Rees, Herbert, 1915-, et al.
Published: (2006)

Design of experiment spreadsheet for injection molding process optimization /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Injection molds and molding :
by: 179539 Dym, Joseph B.
Published: (1987)

Injection molding [kasetvideo]
Published: (1985)

Plastics Injection Molding : Scientific Molding, Recommendations, and Best Practices /
by: Valero, José R. Lerma, author 651639, et al.
Published: (2020)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment /
by: Muhamad Al Baraq Isharudin, 1987-, et al.
Published: (2010)

Design of experiment spreadsheet for injection molding process optimization [electronic resource] /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Injection and compression molding fundamentals/
by: Isayev, Avraam I.
Published: (1987)

Simulation of plastic injection of molding electrical appliances /
by: Nadiah Rahmat, 1986-, et al.
Published: (2009)

Injection molds : 108 proven designs /
by: 360320 Gastrow, Hans, et al.
Published: (1993)

RIM : fundamentals of reaction injection molding/
by: 345476 Macosko, Christopher W.
Published: (1989)

Investigations an effect of sink mark problem on plastic product by process of plastic injection molding /
by: 405779 Nur Aisyah Aimi Abd. Rahman, et al.
Published: (2009)

Determine optimum parameter of plastic injection molding using cae simulation and design of experiment (DOE) /
by: Fairullizam Isahak, 1985-, et al.
Published: (2008)

CAE : computer aided engineering for injection molding/
by: Bernhardt, Ernest C.
Published: (1983)

Process improvement in injection molding using design of experiment /
by: Mohd. Erric Mohammad, 1984-, et al.
Published: (2008)

Investigations an effect of sink mark problem on plastic product by process of plastic injection molding [electronic resource] /
by: 405779 Nur Aisyah Aimi Abd. Rahman, et al.
Published: (2009)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
by: Low, Thuan Himm, 1986-, et al.
Published: (2010)

Injection molding : an introduction /
by: 238633 Potsch, Gerd, et al.
Published: (2008)

Injection molding handbook/
by: Rosato, Dominick V., et al.
Published: (1986)

Reaction injection molding/
by: Becker, Walter E.
Published: (1979)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (2002)

Practical injection molding /
by: 427675 Olmsted, Bernie A., et al.
Published: (2001)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (c200)

Molding of plastics /
by: Bikales, Norbert M.
Published: (1971)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment [electronic resource] /
by: Muhamad Al Baraq Isharudin, 1987-
Published: (2010)

Simulation of plastic injection molding of accessories automotive part using plastic flow analysis software and the Taguchi method /
by: Zaim@Abdul Yamin Mahdi, 1987-, et al.
Published: (2010)

Design and development of a modular mold for producing reflexology mat /
by: Ahmad Fitri Ahmad, 1984-, et al.
Published: (2008)

Flow analysis of injection molds /
by: Kennedy, Peter (Peter K.)
Published: (2013)

Injection molding : critical hurdles /
by: Trombley, Gina, editor
Published: (2015)

How to make injection molds /
by: 360362 Menges, George, et al.
Published: (1993)

Injection mold design engineering /
by: Kazmer, David O., author
Published: (2016)

Understanding injection molding technology /
by: Rees, Herbert, 1915-
Published: (1994)

Injection molding design engineering /
by: 421020 Kazmer, David O.
Published: (2007)

How to make injection molds /
by: Menges, Georg, 1923-, et al.
Published: (2001)

Understanding injection mold design /
by: Rees, Herbert, 1915-
Published: (2001)

A development of computerized FMEA database for plastic injection molding process /
by: Mohamad Rusydi Shukor, 1988-, et al.
Published: (2012)

Injection molding processing data /
by: C., Alberto Naronjo
Published: (2001)

Design and optimization of runner system in plastics injection molding for multi - cavity product /
by: Nur Raihana Sukri, 1985-, et al.
Published: (2009)