Co-injection molding, optimization and taguchi analysis of recycle content product /

Co-injection molding, optimization and taguchi analysis of recycle content product /

Show other versions (1)

Thesis (Sarjana Muda Kejuruteraan (Mekanikal - Pembuatan)) - Universiti Teknologi Malaysia, 2019

Bibliographic Details
Main Authors:	Gooi, Liang Yi, 1995-, author, Rozaimi Mohd. Saad, supervisor, Fakulti Kejuruteraan Mekanikal
Format:
Language:	eng
Published:	Johor Bahru, Johor : Universiti Teknologi Malaysia, 2019
Subjects:	Injection molding of plastics Plastics Taguchi methods (Quality control)

Similar Items

Co-injection molding, optimization and taguchi analysis of recycle content product /
by: Gooi, Liang Yi, 1995-, author
Published: (2019)

A study on co-injection molding process optimization using moldflow and design of experiment on recycled content product /
by: Lim,Wen Theng 1988, et al.
Published: (2012)

Simulation of plastic injection molding of accessories automotive part using plastic flow analysis software and the Taguchi method /
by: Zaim@Abdul Yamin Mahdi, 1987-, et al.
Published: (2010)

Characterization of injection molding parameters using flow simulation and Taguchi method /
by: 434423 Keh, Teng Yang
Published: (2001)

Simulation of plastic injection moulding of card holders using moldex software and the taguchi method /
by: 322443 Choo, Tien Tean, et al.
Published: (2007)

Simulation of plastic injection of molding electrical appliances /
by: Nadiah Rahmat, 1986-, et al.
Published: (2009)

Characterization of injection molding parameter using flow simulation and Taguchi method / [cakera padat]
by: 434423 Keh, Teng Yang
Published: (2001)

Determine optimum parameter of plastic injection molding using cae simulation and design of experiment (DOE) /
by: Fairullizam Isahak, 1985-, et al.
Published: (2008)

Investigations an effect of sink mark problem on plastic product by process of plastic injection molding /
by: 405779 Nur Aisyah Aimi Abd. Rahman, et al.
Published: (2009)

Simulation of plastic injection molding of cup and hand phone holder using moldex software and design of experiment /
by: Low, Thuan Himm, 1986-, et al.
Published: (2010)

Design and optimization of runner system in plastics injection molding for multi - cavity product /
by: Nur Raihana Sukri, 1985-, et al.
Published: (2009)

Simulation of plastic injection molding on a thin part product using moldex software and design of experiment /
by: Muhamad Al Baraq Isharudin, 1987-, et al.
Published: (2010)

Gastrow injection molds : 130 proven designs
by: 360320 Gastrow, Hans, et al.
Published: (c200)

Simulation and optimized analysis of cooling channels of injection molding for food container based autodesk moldflow and design of experiment (DOE) /
by: Khor, Chin Keat, 1989-, et al.
Published: (2015)

To reduce the effect of sink mark in injected moulded part using Taguchi method /
by: 310104 Azmer Abd. Aziz
Published: (2003)

Design mould and simulation of plastic injection moulding of water tap using MOLDEX software and the Taguchi method /
by: 325818 Beh, Chee Hong, et al.
Published: (2007)

Taguchi Optimization of Roundness and Concentricity of a Plastic Injection Molded Barrel of a Telecentric Lens
by: Chao-Ming Lin, et al.
Published: (2021-10-01)

Design of experiment spreadsheet for injection molding process optimization /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Simulation of plastic injection molding of accessories automotive part using plastic flow analysis software and the Taguchi method [electronic resource] /
by: Zaim@Abdul Yamin Mahdi, 1987-
Published: (2010)

A study on gas assisted injection molding : process optimization of CD-ROM tray manufacturing by using Autodesk Moldflow Insight Software and Design of Experiment (DOE) /
by: Lim, Li Xin, 1990-, et al.
Published: (2013)

Injection molds and molding :
by: 179539 Dym, Joseph B.
Published: (1987)

Injection molding [kasetvideo]
Published: (1985)

Selecting injection molds : weighing cost versus productivity /
by: Rees, Herbert, 1915-, et al.
Published: (2006)

A study on gas assisted injection molding [electronic resource] : process optimization of CD-ROM tray manufacturing by using Autodesk Moldflow Insight Software and Design of Experiment (DOE) /
by: Lim, Li Xin, 1990-, et al.
Published: (2013)

Design of experiment spreadsheet for injection molding process optimization [electronic resource] /
by: Ahmad Farhan Ahmad Saberi, 1986-, et al.
Published: (2009)

Injection and compression molding fundamentals/
by: Isayev, Avraam I.
Published: (1987)

Plastics Injection Molding : Scientific Molding, Recommendations, and Best Practices /
by: Valero, José R. Lerma, author 651639, et al.
Published: (2020)

An optimization of the plastic injection molding parameters for sport equipment by using doe methods /
by: Radhwan Hussin, et al.
Published: (2013)

Simulation and optimized analysis of cooling channels of injection molding for food container based autodesk moldflow and design of experiment (DOE) [electronic resource] /
by: Khor, Chin Keat, 1989-, et al.
Published: (2015)

Simulation of plastic injection moulding of a facsimile machine component using moldex software and taguchi method /
by: 458366 Muhammad Adham Abdul Wahab, et al.
Published: (2007)

Injection molds : 108 proven designs /
by: 360320 Gastrow, Hans, et al.
Published: (1993)

RIM : fundamentals of reaction injection molding/
by: 345476 Macosko, Christopher W.
Published: (1989)

Process improvement in injection molding using design of experiment /
by: Mohd. Erric Mohammad, 1984-, et al.
Published: (2008)

Simulation of plastic injection moulding of handphone covers using moldex software and classical method /
by: 458345 Liaw, Tsen Kwang, et al.
Published: (2007)

Injection molding : an introduction /
by: 238633 Potsch, Gerd, et al.
Published: (2008)

Injection molding handbook/
by: Rosato, Dominick V., et al.
Published: (1986)

Reaction injection molding/
by: Becker, Walter E.
Published: (1979)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (2002)

Practical injection molding /
by: 427675 Olmsted, Bernie A., et al.
Published: (2001)

Injection molding handbook /
by: Osswald, Tim A., et al.
Published: (c200)