Relationship between machining parameters and surface roughness of brass using lathe machine.

Relationship between machining parameters and surface roughness of brass using lathe machine.

Surface roughness is a consequence of all machining operations and has been the subject of investigative research for the better part of the last century because the product produce good surface finish is very valuable. But, not all the product needs a good surface finish. If the product not demands...

書目詳細資料
主要作者:	Raja Mohd., Raja Idris
格式:	Undergraduates Project Papers
語言:	English
出版:	2008
主題:	TA Engineering (General). Civil engineering (General)
在線閱讀:	http://umpir.ump.edu.my/id/eprint/755/1/Relationship%20between%20machining%20parameters%20and%20surface%20roughness%20of%20brass%20using%20lathe%20machine.pdf

相似書籍

Effect of lubrication condition on surface roughness by using lathe machine
由: Rohaida, Mohd.
出版: (2008)

Surface roughness in lathe boring operation
由: Alisandra Arieza Fou, Muhd Farid Fou
出版: (2012)

Cylindricity of workpiece in conventional lathe machine
由: Nazihah, Shaharudin
出版: (2009)

Effect of Machining Parameters on Hole Quality of Micro Drilling for Brass
由: Rahman, Azlan, et al.
出版: (2009)

Study of machining parameters of surface roughness in electro discharge machining of tool steel
由: Zairul Ezree , Mohd Yunus
出版: (2008)

Machining surface roughness monitoring using acoustic emission method
由: Mohd Syazlan, Mohd Hatta
出版: (2010)

Relationship between electrode size and machined surface in the EDM machining process
由: Mohd Azrul Aminur, Ismail
出版: (2008)

Effect of surface roughness using different electrodes on electrical discharge machining
由: Mohd Abd Latif, Abd Ghani
出版: (2008)

Rock Mass Surface Roughness Characterization Using Image Analysis Technique
由: Adnan, Raja Asyraf Azizan Raja
出版: (2021)

Surface integrity of titanium when machining with various cutting parameter
由: Mohd 'Azim, Ab. Halim
出版: (2010)

Surface roughness characterization on p20 tool steel in wirecut electrical discharge machining (wedm) process
由: Zaidatul Syima, Zainal
出版: (2013)

Effect of machining parameters on surface textures in wire electro discharge machining of aisi 4140 steel
由: Nurul Shazwani, Mehat
出版: (2008)

Surface Roughness Analysis on Sheet Metals During AWJ Machining Using Low Pressure
由: Nazrin, Mokhtar, et al.
出版: (2023)

Endurance limit of aluminum, brass and mild steel on different surface finish owing to cyclic loads
由: Ahmad Fitri, Zainal Abidin
出版: (2009)

Optimization of cutting parameters and surface roughness on dry turning of low carbon steel
由: Hou, Lo Wei
出版: (2012)

BMM87 bearing load on a brass pin with aluminium plates
由: Mohd Nur Hilmi, Mohd Nazih
出版: (2012)

Optimization of surface roughness in milling by using response surface method (RSM)
由: Mohd Aizuddin, Mat Alwi
出版: (2010)

Analysis and optimum machining parameters on surface roughness and material removal rate for titanium alloy in milling machining with MQL
由: Siti Haryani, Tomadi, et al.
出版: (2023)

Effect of surface roughness on fatigue life
由: Ahmad Kamil, Miskam
出版: (2010)

Adhesion of bacterial on metal surfaces : effect of surface roughness
由: Noratiqah, Chik
出版: (2015)

Surface roughness optimization of face milling operation using Taguchi design method
由: Mohd Azmi, Md Juni
出版: (2008)

Optimization of surface roughness in milling using neural network (NN)
由: Ruzaimi, Zainon
出版: (2010)

Internal surface pipe roughness classification : an acoustic emissions approach
由: Arif Johari, Mat Ali @ Salim
出版: (2009)

Modeling of milling process to predict surface roughness using artificial intelligent method
由: Mohammad Rizal, Abdul Lani
出版: (2009)

Internal surface pipe roughness classification using high frequency acoustic evaluation
由: Amar Reza, Mohammad Firdaus
出版: (2010)

Effect of wheel grinder on the surface roughness when grinding aluminum alloy
由: Muhamad Afiq, Razali
出版: (2010)

Effect of rake angle and feed rate on wear and roughness in machining carbon steel 1045
由: Zamri, Mohd Fawzi, et al.
出版: (2020)

Prediction of surface roughness in turning operation of low carbon steel AISI 1018
由: Fakhrur Razi, Bahrin
出版: (2009)

The morphological and surface roughness of magnetorheological polished AISI 6010 surface
由: Soffarina M., Soffie, et al.
出版: (2020)

Unsupervised Fertigation and Machine Learning for Crop Vegetation Parameter Analysis
由: Mohd Izzat, Mohd Rahman, et al.
出版: (2023)

Monitoring tool wear process in turning machine using acoustic emission technique
由: Azlan, Mohd Saini
出版: (2010)

Speaker localization for human-machine interaction
由: Muhammad Azlan , Ahmad
出版: (2012)

Social and ethical implications of intelligent machines
由: Tijani, Ismaila B., et al.
出版: (2009)

Indirect monitoring of surface quality based on the integration of support vector machine and 3D I-kaz techniques in the machining process
由: Norlida, Jamil
出版: (2023)

Parameter optimization of a cylindrical grinding operation for the quality of surface finish
由: Mohd Asrul, Abu Bakar
出版: (2010)

Process damping technique for aluminium alloy at low speed machining
由: Mohd Azfadir, Mat Daud
出版: (2012)

Face recognition using eigenfaces and smooth support vector machine
由: Mhd, Furqan
出版: (2011)

Modeling UPFC into multi-machine power systems
由: Hassan, L.H., et al.
出版: (2012)

Effect of aging on machinability of 6061 aluminium alloy
由: Emir Izwandy, Dzulkafli
出版: (2010)

The undrained shear strength of soft clay reinforced with 6mm and 10 mm diameter of group bottom ash column
由: Raja Nur Shahira, Raja Sharudin
出版: (2014)