Effect of Build Parameters on the Compressive Behavior of Additive Manufactured CoCrMo Lattice Parts Based on Experimental Design

Effect of Build Parameters on the Compressive Behavior of Additive Manufactured CoCrMo Lattice Parts Based on Experimental Design

Due to their high specific strength, toughness, and corrosion and wear resistance characteristics, CoCrMo alloys are widely used in different industries and applications: wind turbines and jet-engine components, orthopedic implants, dental crowns, etc. The aim of this paper is to investigate the eff...

Full description

Bibliographic Details
Main Authors:	Orhan Gülcan, Ugur Simsek, Okan Cokgunlu, Mirhan Özdemir, Polat Şendur, Guney Guven Yapici
Format:	Article
Language:	English
Published:	MDPI AG 2022-06-01
Series:	Metals
Subjects:	additive manufacturing laser powder bed fusion build orientation volume fraction lattice type
Online Access:	https://www.mdpi.com/2075-4701/12/7/1104

Similar Items

Prediction of Compressive Behavior of Laser-Powder-Bed Fusion-Processed TPMS Lattices by Regression Analysis
by: Uğur Şimşek, et al.
Published: (2024-01-01)

An efficient design methodology for graded surface-based lattice structures using free-size optimization and enhanced mapping method
by: Ugur Simsek, et al.
Published: (2021-11-01)

Compressive deformation behavior and energy absorption characteristic of additively manufactured sheet CoCrMo triply periodic minimal surface lattices
by: So-Yeon Park, et al.
Published: (2022-05-01)

Effect of unit cell topology on the tensile loading responses of additive manufactured CoCrMo triply periodic minimal surface sheet lattices
by: So-Yeon Park, et al.
Published: (2021-08-01)

Dimensional variability characterization of additively manufactured lattice coupons
by: Kirstie Lane Snodderly, et al.
Published: (2022-05-01)

Additive manufacturing of biomimetic Titanium-Tantalum lattices for biomedical implant applications
by: Nicolas Soro, et al.
Published: (2022-06-01)

Effect of Co-Coated Al<sub>2</sub>O<sub>3</sub> Composite Powders on LPBF-Manufactured CoCrMo Alloy
by: Lehui Zhang, et al.
Published: (2023-02-01)

Formation mechanisms and control strategies of metallurgical defects and microstructures during laser powder bed fusion of AlSi10Mg lattice structures
by: Xiangyuan Chen, et al.
Published: (2024-01-01)

Effect of Microstructure and Unit Cell’s Geometry on the Compressive Mechanical Response of Additively Manufactured Co-Cr-Mo Sheet I-WP Lattice
by: So-Yeon Park, et al.
Published: (2022-11-01)

The Static and Fatigue Behavior of AlSiMg Alloy Plain, Notched, and Diamond Lattice Specimens Fabricated by Laser Powder Bed Fusion
by: Hugo Soul, et al.
Published: (2018-04-01)

Heat-Transfer Properties of Additively Manufactured Aluminum Lattice Structures in Combination with Phase Change Material
by: Immanuel Voigt, et al.
Published: (2024-04-01)

Green laser powder bed fusion based fabrication and rate-dependent mechanical properties of copper lattices
by: Sung-Gyu Kang, et al.
Published: (2023-07-01)

Coupled effect of microstructure and topology on the mechanical behavior of Inconel718 additively manufactured lattices
by: S. Banait, et al.
Published: (2022-12-01)

A mechanical comparison of alpha and beta phase biomedical TiTa lattice structures
by: Erin G. Brodie, et al.
Published: (2021-12-01)

Improved mechanical properties and energy absorption of Ti6Al4V laser powder bed fusion lattice structures using curving lattice struts
by: Long Bai, et al.
Published: (2021-12-01)

In Vitro Physical-Chemical Behaviour Assessment of 3D-Printed CoCrMo Alloy for Orthopaedic Implants
by: Radu Mirea, et al.
Published: (2021-05-01)

Dimensionless process development for lattice structure design in laser powder bed fusion
by: Alexander Großmann, et al.
Published: (2020-09-01)

Mechanical Properties of LPBF-Built Titanium Lattice Structures—A Comparative Study of As-Built and Hot Isostatic Pressed Structures for Medical Implants
by: Benedikt Adelmann, et al.
Published: (2022-12-01)

Effect of CoCrMo Addition on Ti6Al4V/xCoCrMo Biomedical Composites Processed by Powder Metallurgy
by: Elena Mihalcea, et al.
Published: (2021-09-01)

Assessing the compressive and tensile properties of TPMS-Gyroid and stochastic Ti64 lattice structures: A study on laser powder bed fusion manufacturing for biomedical implants
by: Miguel Araya, et al.
Published: (2024-03-01)

Compressive mechanical properties of layer hybrid lattice structures fabricated by laser powder bed fusion technique
by: Xin Yang, et al.
Published: (2023-01-01)

Material and process invariant scaling laws to predict porosity of dense and lattice structures in laser powder bed fusion
by: Alexander Großmann, et al.
Published: (2024-02-01)

Enhanced Energy Absorption of Additive-Manufactured Ti-6Al-4V Parts via Hybrid Lattice Structures
by: Seong Je Park, et al.
Published: (2023-10-01)

Strut and sheet metal lattices produced via AM-assisted casting and powder bed fusion: A comparative study
by: Oraib Al-Ketan, et al.
Published: (2023-02-01)

Fabrication and Optimisation of Ti-6Al-4V Lattice-Structured Total Shoulder Implants Using Laser Additive Manufacturing
by: Oliver Bittredge, et al.
Published: (2022-04-01)

Simulation-driven-design of metal lattice structures for a target stress–strain curve
by: Brian McDonnell, et al.
Published: (2024-01-01)

Additive Manufacturing of Honeycomb Lattice Structure—From Theoretical Models to Polymer and Metal Products
by: Tomáš Goldmann, et al.
Published: (2022-03-01)

Impact of contour scanning and helium-rich process gas on performances of Alloy 718 lattices produced by laser powder bed fusion
by: C. Pauzon, et al.
Published: (2022-03-01)

Experimental investigation and numerical modeling of laser powder bed fusion process-induced angle-dependent defects in strut-based lattice structure
by: Heran Jia, et al.
Published: (2022-12-01)

Mechanical-thermal coupling structural failure and in-situ deformation mechanism of cellular high entropy alloy lattice structures
by: Shuai Tong, et al.
Published: (2024-01-01)

Deformation analysis of CoCrMo-on-CoCrMo hip implant based on body mass index using 2D finite element procedure
by: Ammarullah, Muhammad Imam, et al.
Published: (2022)

Von Mises stress analysis of CoCrMo-on-CoCrMo hip prosthesis based on body mass index: 2D FEM estimation
by: Ammarullah, Muhammad Imam, et al.
Published: (2023)

2D finite element deformation investigation on CoCrMo-on-CoCrMo bearing of total hip implant under normal walking condition
by: Ammarullah, Muhammad Imam, et al.
Published: (2023)

Understanding elastic anisotropy in diamond based lattice structures produced by laser powder bed fusion: Effect of manufacturing deviations
by: Markel Alaña, et al.
Published: (2020-10-01)

Investigations on Mechanical Properties of Lattice Structures with Different Values of Relative Density Made from 316L by Selective Laser Melting (SLM)
by: Paweł Płatek, et al.
Published: (2020-05-01)

Detecting missing struts in metallic micro-lattices using high speed melt pool thermal monitoring
by: Jean-Baptiste Forien, et al.
Published: (2023-02-01)

CFD and strength analysis of novel biomimetic lattice structure designed for additive manufacturing and post-processing
by: Saurav Verma, et al.
Published: (2022-12-01)

Dimensional effect and mechanical performance of node-strengthened hybrid lattice structure fabricated by laser powder bed fusion
by: He Liu, et al.
Published: (2023-12-01)

Recycling of Technogenic CoCrMo Alloy by Electron Beam Melting
by: Katia Vutova, et al.
Published: (2022-06-01)

The Influence of Laser Powder Bed Fusion (L-PBF) Process Parameters on 3D-Printed Quality and Stress–Strain Behavior of High-Entropy Alloy (HEA) Rod-Lattices
by: Jianrui Zhang, et al.
Published: (2022-12-01)