Methods of Material and Surface Analysis for the Evaluation of Failure Modes for Electrical Connectors

Methods of Material and Surface Analysis for the Evaluation of Failure Modes for Electrical Connectors

The development of autonomous vehicles and the integration of new information and communication technologies are making the reliability of electrical systems and components in modern vehicles increasingly important. Electrical connectors are a crucial component in an electrical on-board system. They...

Full description

Bibliographic Details
Main Authors:	Philipp Kolmer, Abhay Shukla, Jian Song
Format:	Article
Language:	English
Published:	MDPI AG 2022-11-01
Series:	Technologies
Subjects:	electrical connector failure modes wear fretting corrosion analysis material
Online Access:	https://www.mdpi.com/2227-7080/10/6/124

Similar Items

SOME PARTICULAR ASPECTS OF THE AUTOMOTIVE INDUSTRY CONNECTORS’
by: BĂJENESCU, Titu-Marius I.
Published: (2021-12-01)

Research on the Influence of the Closing Amount of Electrical Connector Contacts on Fretting Wear under a Vibration Environment
by: Baohua Wen, et al.
Published: (2023-05-01)

Characterising mechanical transmission wire ropes’ typical failure modes
by: Edgar Espejo, et al.
Published: (2007-01-01)

Reversible connectors for electrical appliances
by: 8096 British Standards Institution

Evaluation of materials used for coatings of electrical connectors used in the electrical harness of passengers cars
by: Paulina Adamczyk, et al.
Published: (2022-07-01)

Comparison between experimental and analytical behaviour of the steel – concrete composite pushout specimen with stud and channel shear connector
by: P. SANGEETHA, et al.
Published: (2023-06-01)

Steel failure mode of composite dowel shear connector with rectangular regular cutoff
by: Eliane Gomes da Silveira, et al.
Published: (2023-11-01)

Planar Contact Fretting Test Method Applied to Solid Lubricants
by: Henrik Buse, et al.
Published: (2021-05-01)

Mechanically-assisted crevice corrosion and its effect on materials degradation
by: Weichen Xu, et al.
Published: (2023-09-01)

Design requirements for aircraft electrical plug and socket connectors,
by: 5087 International Organization for Standardization

Multi-contact two part printed board electrical connectors with replaceable contacts and through board solder, wire wrap or crimp terminations
by: 8096 British Standards Institution

Investigation of the Behaviour of Steel-Concrete-Steel Sandwich Slabs with Bi-Directional Corrugated-Strip Connectors
by: Mansour Ghalehnovi, et al.
Published: (2020-12-01)

Experimental investigation on corroded stud connectors under strain rates effect
by: Huan-huan Du, et al.
Published: (2023-11-01)

Aircraft pressure refuelling connectors
by: 8096 British Standards Institution

An Experimental Study on the Fretting Corrosion Behaviours of Three Material Pairs at Modular Interfaces for Hip Joint Implants
by: Jian Pu, et al.
Published: (2021-01-01)

Multi-contact rectangular electrical connectors with integral housing (shell). Unsealed with trapezoidal polarized housing and non-removable solder contacts. Full assessment level
by: 8096 British Standards Institution

Electrical connectors of assessed quality for frequencies below 3 MHz : generic data and methods of test
by: 8096 British Standards Institution

Specification for connectors for timber
by: 8096 British Standards Institution

Multi-contact rectangular electrical connector of assessed quality with moulded bodies, unsealed with end guides or jackscrew coupling and front release, rear removable crimp contacts. Full assessment level
by: 8096 British Standards Institution

Installation and inspection of uninsulated compression and mechanical connectors for power cables with copper or aluminium conductors
by: 8096 British Standards Institution

Multi-contact edge socket electrical connectors, single of double sided, close ended with replaceable contacts, through-board solder or wire wrap terminations. Environmental category. Full assessment level
by: 8096 British Standards Institution

Aluminium terminal ends and in-line connectors for hexagonal crimping to aircraft aluminium electrical cables
by: 8096 British Standards Institution

Multi-contact two-part printed board electrical connectors of assessed quality with replaceable contacts and through board solder, solder for wire, wire wrap or crimp terminations - full plus additional assessment
by: 8096 British Standards Institution

Multi-contact edge socket electrical connectors, single or double sided, open ended with metal fixing flanges, guide key location, replaceable contacts and through board solder of wire trap terminations
by: 8096 British Standards Institution

Multi-contact edge socket electrical connector of assessed quality. Single or double sided, open-ended with guide key location replaceable contacts, through board solder or wire wrap terminations - Full assessment level
by: 8096 British Standards Institution

Fretting corrosion /
by: 392966 Waterhouse, R. B.
Published: (1972)

The Effect of Displacement Amplitude on Fretting Wear Behavior and Damage Mechanism of Alloy 690 in Different Gaseous Atmospheres
by: Long Xin, et al.
Published: (2021-10-01)

EXPERIMENTAL SHEAR RESISTANCE EVALUATION OF ORDINARY AND PERFOBOND Y-SHAPED SHEAR CONNECTORS
by: Mohamed Dabaon, et al.
Published: (2015-12-01)

Study on Data-Driven Approaches for the Automated Assembly of Board-to-Board Connectors
by: Hsien-I Lin, et al.
Published: (2022-01-01)

Analysis of the Reliability of Subsea Clamp Connector Based on Multiple Response Surface Methodology
by: Weizheng An, et al.
Published: (2023-07-01)

Numerical Investigation on the Pulling Resistant Capacity of Steel Beam-Concrete Wall Joints with T-stub Connectors
by: He Zhao, et al.
Published: (2023-02-01)

Section specification for airframe-fit circular electrical connectors of assessed quality for low-frequency a.c. and d.c. application (including engin connectors) : requirements for design, performance and testing, and rules for the preparation of detail specifications
Published: (1983)

Origin and evolution of false brinelling and fretting corrosion under rolling conditions
by: Xin Jia, et al.
Published: (2024-01-01)

Fretting and Fretting Corrosion Processes of Ti6Al4V Implant Alloy in Simulated Oral Cavity Environment
by: Marcin Klekotka, et al.
Published: (2020-03-01)

PARTIAL SLIDING OF THE FRETTING PHENOMENON
by: Ştefan GHIMIŞI
Published: (2019-05-01)

IEEE standard for separable insulated connectors for power distribution systems above 600V
by: 11585 American National Standards Institute

ES-PROTECTED ELECTRIC CONNECTOR
by: V.N. Kitaev, et al.
Published: (2023-03-01)

Design of Kinematic Connectors for Microstructured Materials Produced by Additive Manufacturing
by: Miguel R. Silva, et al.
Published: (2021-05-01)

Probabilistic evaluation approach for electrical connector mating: An empirical study on automotive electronic connectors
by: Chunghun HA, et al.
Published: (2017-12-01)

Cable fitting accessories of assessed quality for circular electrical connector : generic data, methods of tests and rules for the preparation of detail specifications
by: 8096 British Standards Institution