Influence of strain rate and temperature on the mechanical behaviour of additively manufactured AlSi10Mg alloy – experiment and the phenomenological constitutive modelling

Influence of strain rate and temperature on the mechanical behaviour of additively manufactured AlSi10Mg alloy – experiment and the phenomenological constitutive modelling

The paper is related to the material behaviour of additively manufactured samples obtained by the direct metal laser sintering (DMLS) method from the AlSi10Mg powder. The specimens are subjected to a quasi-static and dynamic compressive loading in a wide range of strain rates and temperatures to inv...

Full description

Bibliographic Details
Main Authors:	Magda Stanczak, Alexis Rusinek, Paula Broniszewska, Teresa Fras, Piotr Pawłowski
Format:	Article
Language:	English
Published:	Polish Academy of Sciences 2022-08-01
Series:	Bulletin of the Polish Academy of Sciences: Technical Sciences
Subjects:	alsi10mg aluminium alloy additive manufacturing dmls method compression shpb experiment constitutive model
Online Access:	https://journals.pan.pl/Content/124021/PDF/2694_BPASTS_2022_70_4.pdf

Similar Items

Strength and Cyclic Properties of Additive vs. Conventionally Produced Material AlSi<sub>10</sub>Mg
by: Vladimír Chmelko, et al.
Published: (2023-03-01)

Influence on Fatigue Strength of Post-Process Treatments on Thin-Walled AlSi10Mg Structures Made by Additive Manufacturing
by: Nicola Spignoli, et al.
Published: (2023-01-01)

The Influence of Atmospheric Oxygen Content on the Mechanical Properties of Selectively Laser Melted AlSi10Mg TPMS-Based Lattice
by: Ahmad Baroutaji, et al.
Published: (2023-01-01)

Comparison study on additive manufacturing (AM) and powder metallurgy (PM) AlSi10Mg alloys
by: Chen, Biao, et al.
Published: (2020)

Influence of the LPBF Process Parameters on the Porosity of the AlSi10Mg Alloy
by: Sanja Šolić, et al.
Published: (2024-01-01)

Effect of melting modes on microstructure and tribological properties of selective laser melted AlSi10Mg alloy
by: Hong Wu, et al.
Published: (2020-12-01)

Additive manufactured versus cast AlSi10Mg alloy: Microstructure and micromechanics
by: S.I. Shakil, et al.
Published: (2021-06-01)

Fatigue Lifetime Analysis of a Bicycle Frame Made by Additive Manufacturing Technology from AlSi10Mg
by: Matúš Margetin, et al.
Published: (2022-07-01)

Tuning the Hardness of Produced Parts by Adjusting the Cooling Rate during Laser-Based Powder Bed Fusion of AlSi10Mg by Adapting the Process Parameters
by: Artur Leis, et al.
Published: (2022-11-01)

Directed energy deposition of AlSi10Mg: Single track nonscalability and bulk properties
by: Parnian Kiani, et al.
Published: (2020-09-01)

Numerical investigation on effect of different projectile nose shapes on ballistic impact of additively manufactured AlSi10Mg alloy
by: Mahesh Naik, et al.
Published: (2024-01-01)

Process Window for Highly Efficient Laser-Based Powder Bed Fusion of AlSi10Mg with Reduced Pore Formation
by: Artur Leis, et al.
Published: (2021-09-01)

Microstructural analysis and mechanical properties of AlSi10Mg alloy components produced via SLM
by: Ripetskiy A.V., et al.
Published: (2023-01-01)

Development and airworthiness certification of state of art additively manufactured AlSi10Mg mission critical selector valve body part for aerospace
by: Ponnusamy Vignesh, et al.
Published: (2023-09-01)

Microstructure and Wear Resistance of Laser-Treated and Slow Cooled AlSi10Mg-(x)Ni Alloys
by: Danusa Moura, et al.
Published: (2023-08-01)

Influence of 3D Printing Topology by DMLS Method on Crack Propagation
by: Karel Dvorak, et al.
Published: (2021-12-01)

Microstructure and mechanical properties of additively manufactured AlSi10Mg lattice structures from single contour exposure
by: Marcel Sos, et al.
Published: (2023-03-01)

Effect of Scan Strategies and Use of Support Structures on Surface Quality and Hardness of L-PBF AlSi10Mg Parts
by: Ronny M. Gouveia, et al.
Published: (2020-05-01)

Optimisation of the Heat Treatment Profile for Powder-Bed Fusion Built AlSi10Mg by Age Hardening and Ice-Water Quenching
by: Busisiwe J. Mfusi, et al.
Published: (2024-02-01)

Influence of Iron in AlSi10MgMn Alloy
by: Žihalová M., et al.
Published: (2014-12-01)

Novel method of residual stress reduction for AlSi10Mg manufactured using selective laser melting without compromise of mechanical strength
by: Chong Heng Lim, et al.
Published: (2023-01-01)

Selective laser melting of AlSi10Mg : effects of scan direction, part placement and inert gas flow velocity on tensile strength
by: Ahmad Bin Anwar, et al.
Published: (2020)

Corrosion-Fatigue Performance of 3D-Printed (L-PBF) AlSi10Mg
by: Clara Linder, et al.
Published: (2023-08-01)

Very High Cycle Fatigue Life Prediction of SLM AlSi10Mg Based on CDM and SVR Models
by: Yibing Yu, et al.
Published: (2023-09-01)

Microstructure and mechanical property of annealing heat treated AlSi10Mg alloy fabricated by selective laser melting
by: LIANG Enquan, et al.
Published: (2022-05-01)

Pulsed Current Effect on the Hard Anodizing of an AlSi10Mg Aluminum Alloy Obtained via Additive Manufacturing
by: Elisa Dallari, et al.
Published: (2023-03-01)

Mechanical and Microstructure Characterisation of the Hypoeutectic Cast Aluminium Alloy AlSi10Mg Manufactured by the Twin-Roll Casting Process
by: Moritz Neuser, et al.
Published: (2023-07-01)

Developing a best practice for sample preparation of additive manufactured AlSi10Mg for electron backscatter diffraction analysis
by: Erfan Maleki, et al.
Published: (2023-04-01)

Boosting Productivity of Laser Powder Bed Fusion for AlSi10Mg
by: Silvio Defanti, et al.
Published: (2022-09-01)

A Comparative Study of Fatigue Energy Dissipation of Additive Manufactured and Cast AlSi10Mg Alloy
by: Chunxia Yang, et al.
Published: (2021-08-01)

A benchmark activity on the fatigue life assessment of AlSi10Mg components manufactured by L-PBF
by: S. Beretta, et al.
Published: (2022-06-01)

Residual stresses in additively manufactured AlSi10Mg: Raman spectroscopy and X-ray diffraction analysis
by: Silvia Marola, et al.
Published: (2021-04-01)

Influence of Shot Peening on AlSi10Mg Parts Fabricated by Additive Manufacturing
by: Ahmed H. Maamoun, et al.
Published: (2018-06-01)

Effect of Heat Treatment on Ductility and Precipitation Size of Additively Manufactured AlSi10Mg
by: Sandra Megahed, et al.
Published: (2022-08-01)

Investigation on the Microstructure and Mechanical Properties of CNTs-AlSi10Mg Composites Fabricated by Selective Laser Melting
by: Shixuan Luo, et al.
Published: (2021-02-01)

Phase-field simulations and microstructural analysis of epitaxial growth during rapid solidification of additively manufactured AlSi10Mg alloy
by: Jiwon Park, et al.
Published: (2020-10-01)

Laser-powder bed fusion process optimisation of AlSi10Mg using extra trees regression
by: Lisa Minkowitz, et al.
Published: (2023-03-01)

Relationship between Microstructure Evolution and Tensile Properties of AlSi10Mg Alloys with Varying Mg Content and Solidification Cooling Rates
by: Maressa Gandolfi, et al.
Published: (2021-06-01)

Research on Microstructure and Properties of AlSi10Mg Fabricated by Selective Laser Melting
by: Wei Pan, et al.
Published: (2022-03-01)

The Reusability of AlSi10Mg Powder in Directed Energy Deposition
by: Parnian Kiani, et al.
Published: (2024-01-01)