The properties of high-energy milled pre-alloyed copper powders containing 1 wt. % Al

The properties of high-energy milled pre-alloyed copper powders containing 1 wt. % Al

The microstructural and morphological changes of inert gas atomized pre-alloyed Cu-1 wt. % Al powders subjected to hith-energy milling were studied. The microhardness of hot-pressed compacts was measured as a function of milling time. The thermal stability during exposure at 800 °C and the electrica...

Full description

Bibliographic Details
Main Authors:	VISESLAVA RAJKOVIC, DUSAN BOZIC, ALEKSANDAR DEVECERSKI
Format:	Article
Language:	English
Published:	Serbian Chemical Society 2007-01-01
Series:	Journal of the Serbian Chemical Society
Subjects:	Cu-1 wt.% Al pre-alloyed powders high-energy milling grain size hardening electrical conductivity
Online Access:	http://www.shd.org.yu/HtDocs/SHD/Vol72/No1/JSCS_V72_No01-06.pdf

Similar Items

Characteristics of Cu-Al2O3 composites of various starting particle size obtained by high-energy milling
by: Rajković Višeslava, et al.
Published: (2009-01-01)

Effects of jet milling on W–10 wt.%Cu composite powder for injection molding
by: Mingliang Ouyang, et al.
Published: (2020-07-01)

The Effect of Heat Treatments on Alloying of Pre-mixed Al + 4.5 wt. %Cu Powders
by: Kübra KÖPRÜLÜ, et al.
Published: (2018-06-01)

Additive Manufacturing and Precipitation Hardening of Low-Alloyed Copper Alloys Containing Chromium and Hafnium
by: Julia Dölling, et al.
Published: (2024-11-01)

Mechanical and electrical properties of graphene nanosheet reinforced copper matrix composites materials produced by powder metallurgy method
by: Albartouli Ahmed Basheer Mohammed, et al.
Published: (2023-01-01)

Preparation of ultra-fine molybdenum‒copper composite powders and fine-grained molybdenum‒copper alloys
by: WANG Jing-Fei, et al.
Published: (2021-02-01)

Improvement in the PBF-LB/M processing of the Al-Si-Cu-Mg composition through the use of pre-alloyed powder
by: A Martucci, et al.
Published: (2023-01-01)

Investigation of size effect on flow stress of Cu-3wt.%Ag-0.5 wt%Zr thin sheets at room and cryogenic temperature based on geometrically necessary dislocation evolution behavior
by: Han Wang, et al.
Published: (2024-05-01)

Effect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing
by: Feng Li, et al.
Published: (2024-09-01)

Synthesis of Nano-Structured Duplex and Ferritic Stainless Steel Powders by Dry Milling and Its Comparison with Wet Milling
by: R. Shashanka, et al.
Published: (2020-03-01)

Effect of Cooling Rate on the Microstructure and Mechanical Properties of Al-33 wt.% Cu Alloy
by: Yeon-Joo Lee, et al.
Published: (2023-03-01)

Microstructure Analysis of Al-7 wt% Si Alloy Solidified on Earth Compared to Similar Experiments in Microgravity
by: András Roósz, et al.
Published: (2022-08-01)

Characterization of Single Superphosphate Powders – a study of Milling Effects on Solubilization Kinetics
by: Fábio Plotegher, et al.
Published: (2016-02-01)

Simultaneous Increase of Electrical Conductivity and Hardness of Al–1.5 wt.% Mn Alloy by Addition of 1.5 wt.% Cu and 0.5 wt.% Zr
by: Nikolay Belov, et al.
Published: (2019-11-01)

Mechanical properties of hot-pressed Al-4.5 wt. % Cu/WC composite
by: Samaneh Bernoosi, et al.
Published: (2014-12-01)

Nanostructured Powders of AA7075 - SiC Manufactured by High-Energy Ball Milling in a Bath of Isopropyl Alcohol
by: Wésia Amanda de Oliveira Barbosa, et al.
Published: (2023-12-01)

Investigation of the Solid Solution Hardening Mechanism of Low-Alloyed Copper–Scandium Alloys
by: Ramona Henle, et al.
Published: (2024-07-01)

Effect of milling time on the particle size distribution and morphology of tungsten powders
by: YANG Wen-tao, et al.
Published: (2021-10-01)

Lead Silicate Glass Manufacturing by Using Rotary Kiln and Milling of Powder
by: R. A Rahimi
Published: (2013-08-01)

Effect of milling time on mechanical properties of anorthite obtained by thermal transformation of Ca-LTA zeolite
by: Omerašević Mia, et al.
Published: (2022-01-01)

WT1 peptide vaccine in Montanide in contrast to poly ICLC, is able to induce WT1-specific immune response with TCR clonal enrichment in myeloid leukemia
by: Hongtao Liu, et al.
Published: (2018-01-01)

New Denoising Method for Lidar Signal by the WT-VMD Joint Algorithm
by: Zhenzhu Wang, et al.
Published: (2022-08-01)

Circulating microRNA profiles in Wilms tumour (WT): A systematic review and meta-analysis of diagnostic test accuracy
by: Sara Benlhachemi, et al.
Published: (2023-09-01)

Antitumor effect of oral cancer vaccine with Bifidobacterium delivering WT1 protein to gut immune system is superior to WT1 peptide vaccine
by: Toshiro Shirakawa, et al.
Published: (2018-01-01)

Effect of Metal Powder Characteristics on Structural Defects of Graphene Nanosheets in Metal Composite Powders Dispersed by Ball Milling
by: Qi Yan, et al.
Published: (2021-03-01)

Enhanced antitumor activity of a novel, oral, helper epitope-containing WT1 protein vaccine in a model of murine leukemia
by: Hikaru Minagawa, et al.
Published: (2023-02-01)

Enhanced Nanotwinned Copper Bonding through Epoxy-Induced Copper Surface Modification
by: Tsan-Feng Lu, et al.
Published: (2024-04-01)

Interaction effects of milling variables on energy consumption of stirred ball mill for chocolate refining
by: Fišteš Aleksandar, et al.
Published: (2015-01-01)

Effect of Ball Size on the Microstructure and Morphology of Mg Powders Processed by High-Energy Ball Milling
by: Jesus Rios, et al.
Published: (2021-10-01)

Copper-Based Alloys with Optimized Hardness and High Conductivity: Research on Precipitation Hardening of Low-Alloyed Binary CuSc Alloys
by: Julia Dölling, et al.
Published: (2022-05-01)

Effect of jet milling processing on microstructure and mechanical properties of the sintered tungsten powders
by: LI Xing-yu, et al.
Published: (2021-06-01)

Effects on Physicochemical and Dissolution Characteristics of Lentinus edodes Stem Powder by Jet Milling
by: Weitao WANG, et al.
Published: (2023-12-01)

Fabrication of Biochips with Micro Fluidic Channels by Micro End-milling and Powder Blasting
by: Dong Sam Park, et al.
Published: (2008-02-01)

Evaluating Established Roles, Future Perspectives and Methodological Heterogeneity for Wilms’ Tumor 1 (WT1) Antigen Detection in Adult Renal Cell Carcinoma, Using a Novel N-Terminus Targeted Antibody (Clone WT49)
by: Dorin Novacescu, et al.
Published: (2022-04-01)

Analysis of Milling Quality of Reasonably Well Milled Rice with Three Different Grain Shapes
by: AN Hongzhou, JIAO Yue, FEI Xiaoji, XU Jie, HUANG Qing, LIU Jie, YANG Liu, SHI Lijun
Published: (2023-08-01)

Effect of ball milling on the properties of aggregate powder of loess-based support
by: Lu LIU, et al.
Published: (2021-04-01)

Mechanical Characterization of Pharmaceutical Powders by Nanoindentation and Correlation with Their Behavior during Grinding
by: Laura Baraldi, et al.
Published: (2022-05-01)

Numerical simulation of macrosegregation phenomenon in Cu-6wt%Ag alloy ingots fabricated by electromagnetic stirring
by: Qing-shan Yang, et al.
Published: (2024-01-01)

Surface defects in groove milling of Hastelloy-C276 under fluid coolant
by: Al-Falahi, Muath, et al.
Published: (2016)

A study on the effect of nano-precipitates on fracture behavior of nano-structured Al-2wt%Cu alloy fabricated by accumulative roll bonding (ARB) process
by: Azad B., et al.
Published: (2016-01-01)