A new insight into the mechanism of Ce enhancing high temperature oxidation resistance of hot-formed steel

A new insight into the mechanism of Ce enhancing high temperature oxidation resistance of hot-formed steel

In this paper, the effect of Ce addition on high temperature oxidation behavior of hot-formed steel was studied by high temperature oxidation experiment. The structure and phase composition of surface oxide layer of specimens with different Ce content were systematically analyzed by SEM, EDS, XPS. T...

Full description

Bibliographic Details
Main Authors:	Wenbin Du, Chengjun Liu, Hongliang Liu, Yingying Yue, Bo Zhang
Format:	Article
Language:	English
Published:	Elsevier 2024-01-01
Series:	Journal of Materials Research and Technology
Subjects:	Ce addition Hot-formed steel Oxidation behavior Oxidation resistance
Online Access:	http://www.sciencedirect.com/science/article/pii/S223878542303243X

Similar Items

Studying the Effect of Cr and Si on the High-Temperature Oxidation-Resistance Mechanism of Hot Stamping Steel
by: Yanxin Wu, et al.
Published: (2023-09-01)

Inclusion Characteristics in Steel with CeO<sub>2</sub> Nanoparticle Addition
by: Hui Kong, et al.
Published: (2022-11-01)

Tribocorrosion and Abrasive Wear Test of 22MnCrB5 Hot-Formed Steel
by: Dariusz Ulbrich, et al.
Published: (2022-05-01)

Effects of Nb microalloying and quenching rate on microstructure and mechanical properties of hot formed steels
by: CHEN Hua, et al.
Published: (2024-02-01)

Automotive Steel with a High Product of Strength and Elongation used for Cold and Hot Forming Simultaneously
by: Fei Huang, et al.
Published: (2021-02-01)

Enhanced magnetic properties and anisotropy in hot-deformed Ce–Fe–B magnets by suppressing CeFe2 phase with Ga addition
by: Xuefeng Liao, et al.
Published: (2023-11-01)

Effect of Cold and Hot Compounds Forming on Microstructures and Mechanical Properties in the Deformation Zone of Sharp-Edged High-Strength Steel Sections
by: Wenqiu Yao, et al.
Published: (2023-08-01)

Research on dynamic deformation behavior and constitutive relationship of hot forming high strength steel
by: Song Gao, et al.
Published: (2024-01-01)

Study on the Effect of the Pre-Forming of 22MnB5 Steel in Indirect Hot Stamping
by: Ziming Tang, et al.
Published: (2023-05-01)

Hybrid ceramic insulation made of oxide fiber ceramic matrix composite and paper-based ceramic for hot forming tools
by: Elmar Galiev, et al.
Published: (2023-09-01)

Numerical Simulation and Experimental Study of Cold and Hot Composite Forming of Sharp-Edged High-Strength Steel Sections
by: Wenqiu Yao, et al.
Published: (2023-10-01)

A novel hot stamping steel with superior mechanical properties and antioxidant properties
by: Yan Zhao, et al.
Published: (2022-11-01)

An overview of high thermal conductive hot press forming die material development
by: A.R. Zulhishamuddin, et al.
Published: (2015-12-01)

A Review on Hot Stamping of Advanced High-Strength Steels: Technological-Metallurgical Aspects and Numerical Simulation
by: Ireneusz Wróbel, et al.
Published: (2022-05-01)

Effect of trace rare earth elements (Ce) on corrosion resistance of high strength steel used for offshore platform
by: Zhang Xiaoyu, et al.
Published: (2023-01-01)

The Study of Thermal Stability of Mn-Zr-Ce, Mn-Ce and Mn-Zr Oxide Catalysts for CO Oxidation
by: T. N. Afonasenko, et al.
Published: (2022-10-01)

Effect of Mn Addition on Hot-Working Behavior and Microstructure of Hot-Rolled Medium-Mn Steels
by: Adam Skowronek, et al.
Published: (2021-02-01)

Tuning the Cu/Ce Ratio for Improved Benzene Oxidation over Gold-Promoted Alumina-Supported CuO-CeO<sub>2</sub>
by: Tatyana Tabakova, et al.
Published: (2023-01-01)

Photocatalytic Activity of Fibrous Ti/Ce Oxides Obtained by Hydrothermal Impregnation of Short Flax Fibers
by: Mikhail F. Butman, et al.
Published: (2021-06-01)

Formation of thermal oxide scale and its adhesion to hot-rolled low carbon steels with different final strip thicknesses
by: Naipinij Sun, et al.
Published: (2022-01-01)

Hot Gas Forming of Aluminum Alloy Tubes Using Flame Heating
by: Ali Talebi-Anaraki, et al.
Published: (2020-06-01)

Hot Deformation Behaviour of Additively Manufactured 18Ni-300 Maraging Steel
by: Błażej Tomiczek, et al.
Published: (2023-03-01)

Improved Oxidation and Hot Corrosion Resistance of 1Cr11Ni2W2MoV Stainless Steel at 650 °C by a Novel Glass-Ceramic Coating
by: Ken Chen, et al.
Published: (2021-10-01)

Investigation of the Impact of Hot Forming the Properties of Seamless Steel Bottles for Liquefied Gases
by: Vlatko Marušić, et al.
Published: (2020-01-01)

Ultrasonically-assisted synthesis of CeO2 within WS2 interlayers forming type II heterojunction for a VOC photocatalytic oxidation
by: Esmail Doustkhah, et al.
Published: (2023-01-01)

Effect of initial blank temperature in hot press forming towards 22MnB5 springback failure
by: C. H. Ng, et al.
Published: (2019-06-01)

Study on the Removal of Oxide Scale Formed on 300 M Steel Special-Shaped Hot Forging Surfaces during Heating at Elevated Temperature by a High-Pressure Water Descaling Process
by: Fanjiao Gongye, et al.
Published: (2023-02-01)

Effect of Mg-Ce Treatment on Inclusion Characteristics and Pitting Corrosion Behavior in EH420 Marine Steel
by: Zhihong Guo, et al.
Published: (2023-07-01)

Additive Manufacturing of Hot-Forming Dies Using Laser Powder Bed Fusion and Wire Arc Direct Energy Deposition Technologies
by: Artem Alimov, et al.
Published: (2023-11-01)

Integration of Hot Tube Gas Forming and Die Quenching of Ultra-High Strength Steel Hollow Parts Using Low Pressure Sealed-Air
by: Ali Talebi-Anaraki, et al.
Published: (2022-02-01)

A New Phenomenological Model to Predict Forming Limit Curves from Tensile Properties for Hot-Rolled Steel Sheets
by: Wei-Jin Chen, et al.
Published: (2024-01-01)

Study on Deformation Characteristics and Microstructure Evolution of 2205/AH36 Bimetal Composite in a Novel Hot Forming Process
by: Zhou Li, et al.
Published: (2020-10-01)

Assessment of Heat-Affected Zone Softening of Hot-Press-Formed Steel over 2.0 GPa Tensile Strength with Bead-On-Plate Laser Welding
by: Kwangsoo Kim, et al.
Published: (2021-06-01)

Review on precipitates and high-temperature properties of alumina-forming austenitic stainless steel
by: Qiuzhi Gao, et al.
Published: (2023-07-01)

A Comparative Study of the Oxidation Behavior of Hot-Rolled Steel established from Medium and Thin Slabs oxidized in 20% H2O-N2 at 600-900°C
by: Seksan Singthanu, et al.
Published: (2024-02-01)

Influence of Copper Addition on Sigma Phase Precipitation during Hot Deformation of Duplex Steel
by: Grzegorz Stradomski, et al.
Published: (2020-04-01)

Effect of Batch-Annealing Temperature on Oxidation of 22MnB5 Steel during Austenitizing
by: Bibo Li, et al.
Published: (2023-05-01)

Effect of Cooling Mode on the Microstructure of High-Strength Steel during Hot Rolling
by: Hongliang Liu, et al.
Published: (2022-07-01)

High-Temperature Oxidation Behavior of Cr-Ni-Mo Hot-Work Die Steels
by: Yuqi Zhang, et al.
Published: (2022-07-01)

Effect of rare earth Ce addition on inclusions in offshore engineering steel containing arsenic
by: Yinhong Yu, et al.
Published: (2023-01-01)