Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness
One popular method for the protection of gas turbines’ hot sections from high-temperature combustor gases is film cooling. Substantial amounts of research have been conducted to accomplish this task with the minimum cooling flow, maximum surface coverage, and minimal aerodynamic inefficiencies or st...
Main Authors: | , |
---|---|
Format: | Article |
Language: | English |
Published: |
Hindawi Limited
2022-01-01
|
Series: | International Journal of Rotating Machinery |
Online Access: | http://dx.doi.org/10.1155/2022/5994933 |
_version_ | 1798001271416815616 |
---|---|
author | Fan Yang Mohammad E. Taslim |
author_facet | Fan Yang Mohammad E. Taslim |
author_sort | Fan Yang |
collection | DOAJ |
description | One popular method for the protection of gas turbines’ hot sections from high-temperature combustor gases is film cooling. Substantial amounts of research have been conducted to accomplish this task with the minimum cooling flow, maximum surface coverage, and minimal aerodynamic inefficiencies or structural penalties. In this study, a combined experimental and numerical investigation was conducted on three selected film-cooling hole geometries. These geometries were designed with the same initial metering (feed) section, a cylindrical hole of 30° inclination angle, followed by three different forward expansion section geometries. The expansion sections had a 7° laid-back angle and a 17° expansion angle in each lateral direction. However, different interior corner radii were used to blend the metering hole to the exit area, creating three different expansion geometries with almost the same exit areas. In practice, this variation in expansion geometry could represent manufacturing faults or tolerances in laser drilling of the film holes. This study shows that the variations in film-cooling effectiveness are not significant even though the expansion geometries are significantly different. The Pressure Sensitive Paint (PSP) technique was used to obtain the detailed distribution of film-cooling effectiveness on the surface area downstream of these film holes. Adiabatic film cooling effectiveness was measured at blowing ratios of 0.5, 1.0, and 2.0. CFD models of these film holes were also run, and the results were compared with the test data. The major conclusions of this study were that these proposed new geometries produced higher film effectiveness than the conventional 7°-7°-7° diffusion film holes, for the same exit area, the expansion section geometry of the film holes did not have a significant effect on the film coverage, and the numerical results were in good agreement with the test data. |
first_indexed | 2024-04-11T11:33:38Z |
format | Article |
id | doaj.art-7fd401ecc8fe49f48bf16bb990acc19e |
institution | Directory Open Access Journal |
issn | 1542-3034 |
language | English |
last_indexed | 2024-04-11T11:33:38Z |
publishDate | 2022-01-01 |
publisher | Hindawi Limited |
record_format | Article |
series | International Journal of Rotating Machinery |
spelling | doaj.art-7fd401ecc8fe49f48bf16bb990acc19e2022-12-22T04:26:03ZengHindawi LimitedInternational Journal of Rotating Machinery1542-30342022-01-01202210.1155/2022/5994933Effects of Diffusion Film Hole Exit Area on the Film Cooling EffectivenessFan Yang0Mohammad E. Taslim1Mechanical and Industrial Engineering DepartmentMechanical and Industrial Engineering DepartmentOne popular method for the protection of gas turbines’ hot sections from high-temperature combustor gases is film cooling. Substantial amounts of research have been conducted to accomplish this task with the minimum cooling flow, maximum surface coverage, and minimal aerodynamic inefficiencies or structural penalties. In this study, a combined experimental and numerical investigation was conducted on three selected film-cooling hole geometries. These geometries were designed with the same initial metering (feed) section, a cylindrical hole of 30° inclination angle, followed by three different forward expansion section geometries. The expansion sections had a 7° laid-back angle and a 17° expansion angle in each lateral direction. However, different interior corner radii were used to blend the metering hole to the exit area, creating three different expansion geometries with almost the same exit areas. In practice, this variation in expansion geometry could represent manufacturing faults or tolerances in laser drilling of the film holes. This study shows that the variations in film-cooling effectiveness are not significant even though the expansion geometries are significantly different. The Pressure Sensitive Paint (PSP) technique was used to obtain the detailed distribution of film-cooling effectiveness on the surface area downstream of these film holes. Adiabatic film cooling effectiveness was measured at blowing ratios of 0.5, 1.0, and 2.0. CFD models of these film holes were also run, and the results were compared with the test data. The major conclusions of this study were that these proposed new geometries produced higher film effectiveness than the conventional 7°-7°-7° diffusion film holes, for the same exit area, the expansion section geometry of the film holes did not have a significant effect on the film coverage, and the numerical results were in good agreement with the test data.http://dx.doi.org/10.1155/2022/5994933 |
spellingShingle | Fan Yang Mohammad E. Taslim Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness International Journal of Rotating Machinery |
title | Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness |
title_full | Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness |
title_fullStr | Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness |
title_full_unstemmed | Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness |
title_short | Effects of Diffusion Film Hole Exit Area on the Film Cooling Effectiveness |
title_sort | effects of diffusion film hole exit area on the film cooling effectiveness |
url | http://dx.doi.org/10.1155/2022/5994933 |
work_keys_str_mv | AT fanyang effectsofdiffusionfilmholeexitareaonthefilmcoolingeffectiveness AT mohammadetaslim effectsofdiffusionfilmholeexitareaonthefilmcoolingeffectiveness |