Study on fatigue crack growth of electron beam selective melting of titanium alloy

Study on fatigue crack growth of electron beam selective melting of titanium alloy

In the application of additive manufacturing, it is inevitable to use some formed parts with a smaller height. The analysis of various mechanical properties of these formed parts is the focus of research. In this paper, the fatigue performance of a titanium alloy specimen with a 10 mm height and ele...

Descrizione completa

Dettagli Bibliografici
Autori principali:	Zihao Gao, Shanglei Yang, Xuan Meng, Zhentao Wang, Zeng Peng
Natura:	Articolo
Lingua:	English
Pubblicazione:	IOP Publishing 2021-01-01
Serie:	Materials Research Express
Soggetti:	electron beam selective melting titanium alloy fatigue properties secondary cracks
Accesso online:	https://doi.org/10.1088/2053-1591/ac2444

Documenti analoghi

Fatigue growth rate of inclined surface cracks in aluminum and titanium alloys
di: R.R. Yarullin, et al.
Pubblicazione: (2022-04-01)

Low Cycle Fatigue Crack Damage Behavior of TC21 Titanium Alloy with Basketweave Microstructure
di: Baohua Nie, et al.
Pubblicazione: (2022-08-01)

Small fatigue crack growth behavior of TB6 titanium alloy
di: XU Liang, et al.
Pubblicazione: (2019-11-01)

Thermal Fatigue Crack Initiation of Laser Deposited High-temperature Titanium Alloy Ti60A in 20–700 °C
di: Zhang A.L., et al.
Pubblicazione: (2013-08-01)

A Study on Fatigue Crack Closure Associated with the Growth of Long Crack in a New Titanium Alloy
di: Jiarui Liu, et al.
Pubblicazione: (2023-07-01)

The study on the influences of residual stresses on fatigue crack propagation in titanium alloy specimens
di: A. Zangeneh, et al.
Pubblicazione: (2022-12-01)

Effect of morphology of primary a on fatigue crack propagation resistance in a near a heat resistant Titanium alloy
di: Sumi Y., et al.
Pubblicazione: (2020-01-01)

Prediction of Fatigue Crack Growth in Vacuum-Brazed Titanium Alloy
di: Chou-Dian Huang, et al.
Pubblicazione: (2023-11-01)

FATIGUE CRACK GROWTH PERFORMANCE OF TI-6AL-4V TITANIUM ALLOY BY SELECTIVE LASER MELTING
di: ZHANG HaiYing, et al.
Pubblicazione: (2023-12-01)

FATIGUE CRACKING MECHANISMS OF TITANIUM ALLOY VT3-1 IN VERY-HIGH-CYCLE-FATIGUE REGIME
di: A. A. Shanyavskiy, et al.
Pubblicazione: (2016-11-01)

Inclusions in melting process of titanium and titanium alloys
di: Meng-jiang Cen, et al.
Pubblicazione: (2019-07-01)

SIMULATION OF FATIGUE CRACK INITIATION LIFE OF TC4 TITANIUM ALLOY BASED ON ITS MESOSCOPIC PROPERTIES
di: JIANG Ze, et al.
Pubblicazione: (2021-01-01)

Spatial and Direction-Based Characterization of Microstructures and Microhardness of TA15 Titanium Alloy Produced by Electron Beam Melting
di: Jiangtao Ran, et al.
Pubblicazione: (2021-04-01)

Fatigue crack growth behavior of Inconel 718 produced by selective laser melting
di: R. Konecná, et al.
Pubblicazione: (2015-12-01)

Fatigue crack growth behavior of Inconel 718 produced by selective laser melting
di: R. Konecná, et al.
Pubblicazione: (2015-12-01)

Fatigue improvement of electron beam melting-fabricated biomedical Co–Cr–Mo alloy by accessible heat treatment
di: Daixiu Wei, et al.
Pubblicazione: (2018-01-01)

Crack path in aeronautical titanium alloy under ultrasonic torsion loading
di: A. Nikitin, et al.
Pubblicazione: (2015-12-01)

Crack path in aeronautical titanium alloy under ultrasonic torsion loading
di: A. Nikitin, et al.
Pubblicazione: (2016-01-01)

Identification of Relationships between Heat Treatment and Fatigue Crack Growth of αβ Titanium Alloys
di: Vincent Renon, et al.
Pubblicazione: (2019-04-01)

Fatigue-Damage Initiation at Process Introduced Internal Defects in Electron-Beam-Melted Ti-6Al-4V
di: Robert Fleishel, et al.
Pubblicazione: (2023-02-01)

In situ fabrication of a titanium-niobium alloy with tailored microstructures, enhanced mechanical properties and biocompatibility by using selective laser melting
di: Zhao, Danlei, et al.
Pubblicazione: (2020)

Research Progress on Surface Polishing Technology of Powder Bed Fusion Titanium Alloy
di: ZHOU Di, WU Songquan, LI Ziyang, LIU Lei, YANG Yi, WANG Hao, HUANG Aijun
Pubblicazione: (2024-08-01)

Experimental investigation of crack initiation and propagation in high- and gigacycle fatigue in titanium alloys by study of morphology of fracture
di: M.V. Bannikov, et al.
Pubblicazione: (2015-12-01)

Experimental investigation of crack initiation and propagation in high- and gigacycle fatigue in titanium alloys by study of morphology of fracture
di: M.V. Bannikov, et al.
Pubblicazione: (2016-01-01)

The use of various peening methods to improve the fatigue strength of titanium alloy Ti6Al4V manufactured by electron beam melting
di: Hitoshi Soyama, et al.
Pubblicazione: (2018-10-01)

Study of Formed Oxides in IN718 Alloy during the Fabrication by Selective Laser Melting and Electron Beam Melting
di: Hao Yu, et al.
Pubblicazione: (2018-12-01)

Low Cycle Fatigue Behavior of TC21 Titanium Alloy with Bi-Lamellar Basketweave Microstructure
di: Baohua Nie, et al.
Pubblicazione: (2022-06-01)

Dual-Material Electron Beam Selective Melting: Hardware Development and Validation Studies
di: Chao Guo, et al.
Pubblicazione: (2015-03-01)

Fatigue Crack Growth in Maraging Steel Obtained by Selective Laser Melting
di: Fernando Antunes, et al.
Pubblicazione: (2019-10-01)

Fatigue Assessment of Ti–6Al–4V Circular Notched Specimens Produced by Selective Laser Melting
di: Seyed-Mohammad-Javad Razavi, et al.
Pubblicazione: (2017-07-01)

Corrosion fatigue behavior of porous Cu-bearing Ti alloy fabricated by selective laser melting
di: Ying Sun, et al.
Pubblicazione: (2023-03-01)

Study of the Intrinsic Factors Determining the Near-Threshold Fatigue Crack Propagation Behavior of a High-Strength Titanium Alloy
di: Huan Wang, et al.
Pubblicazione: (2025-01-01)

Fatigue Assessment of Selective Laser Melted Ti-6Al-4V: Influence of Speed Manufacturing and Porosity
di: Unai Segurajauregi, et al.
Pubblicazione: (2021-06-01)

Effects of Anisotropic Microstructure and Load Ratio on Fatigue Crack Propagation Rate in Additively Manufactured Ti-6Al-4V Alloy
di: Elad Chakotay, et al.
Pubblicazione: (2024-12-01)

Microstructure and machinability of selective laser melted titanium alloy in micro-milling
di: Muhammad Rehan, et al.
Pubblicazione: (2024-11-01)

Improvement on mechanical properties and corrosion resistance of titanium-tantalum alloys in-situ fabricated via selective laser melting
di: Zhao, Danlei, et al.
Pubblicazione: (2020)

EXPERIMENTAL RESEARCH ON MECHANICAL PROPERTIES OF TITANIUM ALLOY AIRCRAFT STRUCTURE MAINTENANCE PARTS BY ADDITIVE MANUFACTURING
di: LIU ShiHua, et al.
Pubblicazione: (2023-12-01)

Electron beam surface melting of MoSiBTiC alloys: Effect of preheating on cracking behavior and microstructure evolution
di: Masaya Higashi, et al.
Pubblicazione: (2021-11-01)

Effect of Basketweave Microstructure on Very High Cycle Fatigue Behavior of TC21 Titanium Alloy
di: Baohua Nie, et al.
Pubblicazione: (2018-05-01)

New Ti–35Nb–7Zr–5Ta Alloy Manufacturing by Electron Beam Melting for Medical Application Followed by High Current Pulsed Electron Beam Treatment
di: Maria Surmeneva, et al.
Pubblicazione: (2021-07-01)