Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures
3D printing is a popular technique for fabricating three-dimensional solid objects from a digital design. In order to produce high quality 3D printed parts, the appropriate selection of printing parameters is crucial. This research is focused on studying the properties of 3D printed specimens (i.e.,...
| Main Authors: | , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
KeAi Communications Co., Ltd.
2020-09-01
|
| Series: | International Journal of Lightweight Materials and Manufacture |
| Subjects: | |
| Online Access: | http://www.sciencedirect.com/science/article/pii/S2588840420300196 |
| _version_ | 1828470841941164032 |
|---|---|
| author | Chamil Abeykoon Pimpisut Sri-Amphorn Anura Fernando |
| author_facet | Chamil Abeykoon Pimpisut Sri-Amphorn Anura Fernando |
| author_sort | Chamil Abeykoon |
| collection | DOAJ |
| description | 3D printing is a popular technique for fabricating three-dimensional solid objects from a digital design. In order to produce high quality 3D printed parts, the appropriate selection of printing parameters is crucial. This research is focused on studying the properties of 3D printed specimens (i.e., mechanical, thermal and morphological) with varying processing conditions such as infill pattern, infill density and infill speed, and also with different printing materials. A number of testing techniques such as tensile, bending, compression, differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), thermal imaging, and scanning electron microscopy (SEM) were used for performing a comprehensive analysis. The results showed that Young's modulus of the printed parts increased with the increase of infill density. For pure PLA, parts with 100% infill density obtained the highest Young's modulus of 1538.05 MPa. Of the tested infill speeds from 70 to 110 mm/s; 90 mm/s infill speed gave the highest Young's modulus for pure PLA. Meanwhile, there was a slight difference of Young's modulus between low speeds (70 mm/s and 80 mm/s) and high speeds (100 mm/s and 110 mm/s) compared to the commonly used infill speed of 90 mm/s. The level of crystallinity of the 3D printed PLA specimens did not directly influence the mechanical properties as was confirmed by the DSC results. SEM images showed that the strength of the printed samples was dependent upon the arrangement of their layers. Furthermore, it was found that the most appropriate processing temperature and infill speed for pure PLA filament are 215 °C and 90 mm/s, respectively. Among the five printing materials tested, carbon fibre reinforced PLA (CFR-PLA) gave the highest Young's modulus of 2637.29 MPa at 90 mm/s. Voids inside the matrix and the gaps between layers lead to initiation of cracks of the specimens. Overall, 100% infill density, 90 mm/s infill speed, 215 °C of set nozzle temperature, and the linear fill pattern were the possible optimal process settings for the most improved performance of the five different printing materials used in this study. |
| first_indexed | 2024-12-11T05:00:29Z |
| format | Article |
| id | doaj.art-a938098e2b784212bbb5df2b0dfd21b8 |
| institution | Directory Open Access Journal |
| issn | 2588-8404 |
| language | English |
| last_indexed | 2024-12-11T05:00:29Z |
| publishDate | 2020-09-01 |
| publisher | KeAi Communications Co., Ltd. |
| record_format | Article |
| series | International Journal of Lightweight Materials and Manufacture |
| spelling | doaj.art-a938098e2b784212bbb5df2b0dfd21b82022-12-22T01:20:10ZengKeAi Communications Co., Ltd.International Journal of Lightweight Materials and Manufacture2588-84042020-09-0133284297Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structuresChamil Abeykoon0Pimpisut Sri-Amphorn1Anura Fernando2Corresponding author.; Northwest Composites Centre, Aerospace Research Institute, Department of Materials, Faculty of Science and Engineering, The University of Manchester, Sackville Street, Manchester, M13 9PL, UKNorthwest Composites Centre, Aerospace Research Institute, Department of Materials, Faculty of Science and Engineering, The University of Manchester, Sackville Street, Manchester, M13 9PL, UKNorthwest Composites Centre, Aerospace Research Institute, Department of Materials, Faculty of Science and Engineering, The University of Manchester, Sackville Street, Manchester, M13 9PL, UK3D printing is a popular technique for fabricating three-dimensional solid objects from a digital design. In order to produce high quality 3D printed parts, the appropriate selection of printing parameters is crucial. This research is focused on studying the properties of 3D printed specimens (i.e., mechanical, thermal and morphological) with varying processing conditions such as infill pattern, infill density and infill speed, and also with different printing materials. A number of testing techniques such as tensile, bending, compression, differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), thermal imaging, and scanning electron microscopy (SEM) were used for performing a comprehensive analysis. The results showed that Young's modulus of the printed parts increased with the increase of infill density. For pure PLA, parts with 100% infill density obtained the highest Young's modulus of 1538.05 MPa. Of the tested infill speeds from 70 to 110 mm/s; 90 mm/s infill speed gave the highest Young's modulus for pure PLA. Meanwhile, there was a slight difference of Young's modulus between low speeds (70 mm/s and 80 mm/s) and high speeds (100 mm/s and 110 mm/s) compared to the commonly used infill speed of 90 mm/s. The level of crystallinity of the 3D printed PLA specimens did not directly influence the mechanical properties as was confirmed by the DSC results. SEM images showed that the strength of the printed samples was dependent upon the arrangement of their layers. Furthermore, it was found that the most appropriate processing temperature and infill speed for pure PLA filament are 215 °C and 90 mm/s, respectively. Among the five printing materials tested, carbon fibre reinforced PLA (CFR-PLA) gave the highest Young's modulus of 2637.29 MPa at 90 mm/s. Voids inside the matrix and the gaps between layers lead to initiation of cracks of the specimens. Overall, 100% infill density, 90 mm/s infill speed, 215 °C of set nozzle temperature, and the linear fill pattern were the possible optimal process settings for the most improved performance of the five different printing materials used in this study.http://www.sciencedirect.com/science/article/pii/S2588840420300196Infill density, speed and patternNozzle speed and temperatureCarbon fibreCarbon nanotubesThermal imagingMechanical, thermal and morphological properties |
| spellingShingle | Chamil Abeykoon Pimpisut Sri-Amphorn Anura Fernando Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures International Journal of Lightweight Materials and Manufacture Infill density, speed and pattern Nozzle speed and temperature Carbon fibre Carbon nanotubes Thermal imaging Mechanical, thermal and morphological properties |
| title | Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures |
| title_full | Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures |
| title_fullStr | Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures |
| title_full_unstemmed | Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures |
| title_short | Optimization of fused deposition modeling parameters for improved PLA and ABS 3D printed structures |
| title_sort | optimization of fused deposition modeling parameters for improved pla and abs 3d printed structures |
| topic | Infill density, speed and pattern Nozzle speed and temperature Carbon fibre Carbon nanotubes Thermal imaging Mechanical, thermal and morphological properties |
| url | http://www.sciencedirect.com/science/article/pii/S2588840420300196 |
| work_keys_str_mv | AT chamilabeykoon optimizationoffuseddepositionmodelingparametersforimprovedplaandabs3dprintedstructures AT pimpisutsriamphorn optimizationoffuseddepositionmodelingparametersforimprovedplaandabs3dprintedstructures AT anurafernando optimizationoffuseddepositionmodelingparametersforimprovedplaandabs3dprintedstructures |