The periodic cooling tower - flow visualization, surface roughening, and full scale model
Improvement of the environmental and economic characteristics of cooling towers, pt.2
| Main Author: | |
|---|---|
| Format: | Technical Report |
| Language: | en_US |
| Published: |
MIT Energy Lab
2005
|
| Subjects: | |
| Online Access: | http://hdl.handle.net/1721.1/27271 |
| _version_ | 1826191695081897984 |
|---|---|
| author | Hon, Pou Cheong |
| author_facet | Hon, Pou Cheong |
| author_sort | Hon, Pou Cheong |
| collection | MIT |
| description | Improvement of the environmental and economic characteristics of cooling towers, pt.2 |
| first_indexed | 2024-09-23T08:59:54Z |
| format | Technical Report |
| id | mit-1721.1/27271 |
| institution | Massachusetts Institute of Technology |
| language | en_US |
| last_indexed | 2024-09-23T08:59:54Z |
| publishDate | 2005 |
| publisher | MIT Energy Lab |
| record_format | dspace |
| spelling | mit-1721.1/272712019-04-10T20:09:04Z The periodic cooling tower - flow visualization, surface roughening, and full scale model Hon, Pou Cheong Cooling towers Heat exchangers Fluid dynamics Improvement of the environmental and economic characteristics of cooling towers, pt.2 The concept of periodic towers is to have sheet metal discs partially submerged in hot, power plant condenser effluent. As the discs rotate, local sections of the discs alternately absorb heat from the effluent and discharge heat to the air. The means of heat transfer on the air side can be either evaporative and/or convective, depending upon the amount of effluent carried into the air side on the surface of the plates. An oil layer, floated on the water's surface, has been shown to be effective in eliminating water carry-over to the air side. The advantages of the periodic tower lie in the low cost of the discs and the ability to operate dry. A periodic tower is significantly less expensive than a conventional dry tower fabricated with finned tubes. Further, with the capacity of being operated wet, the high capacity losses incurred during warm months by finned tube towers can be eliminated. The effort to evaluate periodic cooling towers has been a three-pronged thrust: 1) A full scale model of a periodic heat exchanger was designed and is being built to optimize the overall performance and determine the economic competitiveness of this new form of heat exchanger. In the periodic exchanger cooling air is forced over the top portion of a long horizontal row of circular discs slowly rotating in a hot water bath. This large model, over twenty-five feet long and ten feet high with a two and one half by one foot test section, will provide actual test data to verify previous performance optimization calculations and allow for research and development to continue on many design details for this new concept. 2) Disc Ribbing - Roughened Surfaces An existing computer design routine for optimizing periodic cooling towers has been modified by increasing the number of variables from 5 to 8. This was done to account for the effects of roughened surfaces on heat exchanger performance. The modified optimum computer design program yields a periodic tower configuration having the lowest incremental cost for power operation, but it is impractical because the optimized rib heights are smaller than the oil film clinging to the discs. Taking into account the effect of the coating oil thickness on the surfaces, sensitivity studies on the influences of the roughened surfaces on the incremental cost have been made. A specific 5 ft. diameter roughened surface heat exchanger yields a 15 to 20% savings of capital and incremental cost over a smooth heat exchanger of the same diameter. This economically warrants the use of roughened rather than smooth surfaces for periodic heat exchangers. 3) Flow visualization tests indicate that the mixing of water in the periodic exchanger trough is strongly dependent upon both the water's inlet and outlet points, and the rotational direction of the plates. Various mixing currents in the trough for different geometries have been observed by use of dye injection. Silicone oils, because of their lower vapor pressure and subsequent low rate of evaporation, appear to be superior to petroleum based oils. Empire State Electric Energy Research Corporation, New York 2005-09-15T14:51:26Z 2005-09-15T14:51:26Z 1974 Technical Report 01482817 http://hdl.handle.net/1721.1/27271 en_US MIT-EL 74-008 3507708 bytes application/pdf application/pdf MIT Energy Lab |
| spellingShingle | Cooling towers Heat exchangers Fluid dynamics Hon, Pou Cheong The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title | The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title_full | The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title_fullStr | The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title_full_unstemmed | The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title_short | The periodic cooling tower - flow visualization, surface roughening, and full scale model |
| title_sort | periodic cooling tower flow visualization surface roughening and full scale model |
| topic | Cooling towers Heat exchangers Fluid dynamics |
| url | http://hdl.handle.net/1721.1/27271 |
| work_keys_str_mv | AT honpoucheong theperiodiccoolingtowerflowvisualizationsurfacerougheningandfullscalemodel AT honpoucheong periodiccoolingtowerflowvisualizationsurfacerougheningandfullscalemodel |