Ink jet nozzle test station

Ink jet nozzle test station

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 1999.

Detalhes bibliográficos
Autor principal:	Grover, Garth K. (Garth Kneeland), 1973-
Outros Autores:	Emanuel M. Sachs.
Formato:	Thesis
Idioma:	eng
Publicado em:	Massachusetts Institute of Technology 2013
Assuntos:	Mechanical Engineering
Acesso em linha:	http://hdl.handle.net/1721.1/80504

Registos relacionados

Ink jet printing of PZT thin films for MEMS
Por: Bathurst, Stephen, 1980-
Publicado em: (2013)

Optimization of PZT processing using thermal ink-jet printing
Por: Jeon, Jessie Sungyun
Publicado em: (2009)

Study of jet-swirl nozzle plate for spray cooling
Por: Tan, Yunn Boon.
Publicado em: (2013)

Drop-on-demand ink jet printing for three dimensional printer application
Por: Kohnen, Anne Stuart
Publicado em: (2005)

Analysis of wear on abrasive water jet nozzle
Por: Izzudin, Nazar
Publicado em: (2016)

Effect of nozzle diameter on jet impingement cooling system
Por: Dulfharah, Nizam Memth Ali
Publicado em: (2009)

Effect of nozzle angle on jet impingement cooling system
Por: Khaider, Abu Bakar
Publicado em: (2009)

Investigation of continuous-jet nozzle design and fabrication for three dimensional printing
Por: Hämeenanttila, Tiina
Publicado em: (2005)

Uniroo--a one legged dynamic hopping robot
Por: Zeglin, Garth J. (Garth John)
Publicado em: (2005)

Dispersion of water sprays in a transverse air jet and the aging of spray nozzles
Por: Eletribi, Shereen, 1975-
Publicado em: (2007)

A fast flexible ink-jet printing method for patterning networks of neurons in culture
Por: Fuller, Sawyer Buckminster, 1977-
Publicado em: (2014)

Designing a new joint for the iXa walker
Por: Grove, Garth S
Publicado em: (2010)

Mitigation of under-expanded supersonic jet noise through stepped nozzles
Por: Wei, Xiaofeng, et al.
Publicado em: (2021)

Vortex behaviour and velocity characteristics of jets issuing from hybrid inclined elliptic nozzles
Por: New, T. H., et al.
Publicado em: (2013)

Ink jet deposition of inorganic nanoparticle materials as a route to desktop fabrication of integrated logic and micromachinery
Por: Fuller, Sawyer Buckminster, 1977-
Publicado em: (2014)

Ink-jet printing of transparent and stretchable electrodes for dielectric elastomer actuator
Por: Shrestha, Milan, et al.
Publicado em: (2018)

High resolution aerosol jet printing of conductive ink for stretchable electronics
Por: Goh, Guo Liang, et al.
Publicado em: (2018)

A machine learning based logic branching algorithm for automated assembly
Por: Vaaler, Erik Garth
Publicado em: (2008)

Performance evaluation of water Jet Pump for Nozzle to throat area ratios on suction lift
Por: Md. Mizanur Rahman, et al.
Publicado em: (2014)

Ink-Jet Printing of Micro-Electro-Mechanical Systems (MEMS)
Por: Lau, Gih-Keong, et al.
Publicado em: (2017)

Single nozzle micropump
Por: Charles Tanu Wijaya.
Publicado em: (2011)

Near- and far-field acoustic measurements for stepped nozzles at over- and perfectly-expanded supersonic jet flow conditions
Por: Wei, X. F., et al.
Publicado em: (2022)

Needle-free injection nozzle geometry
Por: Liu, John (John Hsiao-Yung)
Publicado em: (2018)

Development of 3D printable food ink
Por: Lai, Xue Hao
Publicado em: (2020)

Development of 3D printable food ink
Por: Ng, Elson Yu Sheng
Publicado em: (2020)

Design for ink-jet printing and micropattern generation on micro components
Por: Lee, Chee Loong.
Publicado em: (2009)

Proper orthogonal decomposition analysis of near-field coherent structures associated with V-notched nozzle jets
Por: Lim, H.D., et al.
Publicado em: (2021)

Behavior of microdroplets in diffuser/nozzle structures
Por: Liu, Jing, et al.
Publicado em: (2012)

Ink-jet printed In-Ga-Zn oxide thin film transistors
Por: Wang, Ye.
Publicado em: (2013)

Mixing characteristics of inclined dense jets with different nozzle geometries
Por: Jiang, Mingtao, et al.
Publicado em: (2021)

Effects of nozzle geometry on flapper valve characteristics
Por: Mennell, Roy F. (Roy Franklin)
Publicado em: (2015)

Effects of bevelled nozzles on standoff shocks in supersonic impinging jets
Por: Lim, Haoxiang Desmond, et al.
Publicado em: (2021)

Develop protein-fortified 3D-printable food inks
Por: How, Qiao Xin
Publicado em: (2021)

Flow characterization of supersonic jets issuing from double-beveled nozzles
Por: Wu, Jie, et al.
Publicado em: (2019)

A computational fluid dynamic study of supersonic beveled nozzle jets
Por: Tay, Sarah Ching Wen
Publicado em: (2017)

An investigation on supersonic bevelled nozzle jets
Por: Wu, Jie, et al.
Publicado em: (2017)

A geometrically exact dynamic model for spatial elastic rods
Por: Beretta, Robert K. (Robert Kneeland)
Publicado em: (2007)

Study of deposit formation inside diesel injectors nozzles
Por: Wang, YinChun, Ph. D. Massachusetts Institute of Technology
Publicado em: (2013)

Non-equilibrium condensation of carbon dioxide in supersonic nozzles.
Por: Duff, Karl Melton
Publicado em: (2005)

Study on spray nozzle of diesel engine
Por: Nur Syafiqah, Mohd Nawawi
Publicado em: (2011)