Motor selection via impedance-matching for driving nonlinearly damped, resonant loads

Motor selection via impedance-matching for driving nonlinearly damped, resonant loads

This paper presents a novel method for selecting the most appropriate motor–gearhead combination for nonlinearly damped, resonant loads. The method extends to the nonlinear damping case the impedance-matching condition which is used to guarantee a maximum power transfer in linear network theory. In...

Descrizione completa

Dettagli Bibliografici
Autore principale:	Campolo, Domenico
Altri autori:	School of Mechanical and Aerospace Engineering
Natura:	Journal Article
Lingua:	English
Pubblicazione:	2014
Soggetti:	DRNTU::Engineering::Aeronautical engineering::Aircraft motors and engines
Accesso online:	https://hdl.handle.net/10356/100162 http://hdl.handle.net/10220/24102

Documenti analoghi

Solar uav: propulsion system - selection of motor and propeller for male uav
di: Ong, Chin Hwee
Pubblicazione: (2014)

Solar UAV : propulsion system : selection of motor and propeller for MALE UAV
di: Tan, Adrian Seng Leong
Pubblicazione: (2013)

Characterization of vibration motors for micro aerial vehicles
di: Loo, Phuay Keong.
Pubblicazione: (2010)

Modelling and verification of hybrid electric propulsion system
di: Ng, Marcus Jun Jie
Pubblicazione: (2021)

Effect of macroscopic stress, cold work and microstructure on the resistivity and hall coefficient in NI based superalloys
di: Shao, Zhaoyu
Pubblicazione: (2020)

Experimental investigation of a distributed propulsion system
di: Mehta, Ronak Chittesh
Pubblicazione: (2022)

Design of jet engine component : fan blade
di: Lee, Wen Jun
Pubblicazione: (2018)

CFD simulations on the compressor of a mini jet engine-I
di: Chong, Clarence Yew Keong.
Pubblicazione: (2013)

Approximating conditions within a multistage axial compressor and assessing the possibility of hot surface ignition on the heated surfaces
di: Koh, Alan Fu Hai
Pubblicazione: (2018)

Advanced aerospace research on the new generation of turbo-fan engine exhaust mixer
di: Yu, Simon Ching Man., et al.
Pubblicazione: (2008)

An optimal (S-1, S) inventory control policy for multi-indentured aircraft engine spare parts
di: Ang, Eugene Zheng Hao
Pubblicazione: (2010)

Centrifugal compressor study in mini-jet engine
di: Guo, Shuai.
Pubblicazione: (2013)

Development of an aircraft gas turbine engine dynamic simulation software
di: Yang, Jie
Pubblicazione: (2009)

An experimental study validating the conditions necessary to prevent the formation and ingestion of aero-inlet vortices
di: Omar Faruq Idris
Pubblicazione: (2014)

Selective surface modification of PET substrate for inkjet printing
di: Yeo, L. P, et al.
Pubblicazione: (2014)

Numerical investigation on influence of fuselage on multirotor wake vortex structures in forward flight
di: Wang, John Chung-Hung, et al.
Pubblicazione: (2022)

Solar UAV : design and fabrication of structural test rig for loading and testing a 7.5m half wing
di: Chua, Zac Zheng Xun.
Pubblicazione: (2013)

Investigation into micro and nano scale optical metrology for shiny surfaces and difficult to access aircraft engine components
di: Haridas, Aswin
Pubblicazione: (2020)

Aerodynamic data generation and design support for solar UAV : CFD for aircraft loads
di: Muhammad Fursham Mohd Zubir
Pubblicazione: (2014)

Predictive maintenance system for aircraft engine using AI
di: Wang, Terence You Gui
Pubblicazione: (2022)

Combustion simulation of gas diffusion mixing
di: Chee, Yin Yong.
Pubblicazione: (2011)

Study of avian inspired features for UAV design
di: Lau, Leon
Pubblicazione: (2020)

Design and sizing of evtol aircraft (development of complex lightweight mechanical actuating devices for eVTOL aircraft - Prototyping & Integration)
di: Hau, Jun Fei
Pubblicazione: (2022)

Development of a quadplane
di: Chng, Joel Li Wei
Pubblicazione: (2022)

Analysis and modelling of 3D printed springs for use in spacecraft
di: Sacco, Enea
Pubblicazione: (2020)

An experimental investigation on tapered wings with leading-edge protuberances
di: Ee, Marcus Joon Leng
Pubblicazione: (2023)

System identification for longitudinal derivatives for a VTOL UAV
di: Liang, QiYun
Pubblicazione: (2020)

Design and sizing eVTOL aircraft (aerodynamics portion)
di: Dikshit, Abhijnan
Pubblicazione: (2022)

Study on emerging technologies for aerospace application
di: Mohammed Naufal Nur Hakim
Pubblicazione: (2019)

In-flight simulation of tilt-rotor VTOL UAV using open loop wind tunnel
di: Wong, Amos Timothy Jun Han
Pubblicazione: (2022)

Investigation and modeling of flight technical error (FTE) associated with UAS operating with and without pilot guidance
di: Wang, John Chung-Hung, et al.
Pubblicazione: (2021)

Study of impact and transient vibration of aircraft landing gear
di: Hong, Weiling.
Pubblicazione: (2009)

Adhesion and characterization of the interface between aerospace standard primer and anodized aluminium alloy
di: Toh, Xin Hui
Pubblicazione: (2015)

Micro air vehicles : flapping wing propulsion
di: Koay, Say Seng.
Pubblicazione: (2011)

Design, fabrication, evaluation of low-speed UAV wing flap actuated with shape memory alloy
di: Seow, Aik Khiam
Pubblicazione: (2009)

Design of a latching mechanism for perching UAVs
di: Koh, Martin Wei Xiang.
Pubblicazione: (2011)

Stress intensity factors of cracks in straight lug
di: Lam, Wei Wei
Pubblicazione: (2015)

Design and fabrication of vibrator-activated wing flappers
di: Goh, Chen Lieng.
Pubblicazione: (2011)

Development of a twin-turboprop aircraft model for NTU flight simulator
di: Ng, Zi Jian.
Pubblicazione: (2009)

Flapping wing mechanism for micro aerial vehicles
di: Yeo, Janan Yul Chen.
Pubblicazione: (2009)