Real time assessment of smart concrete inspection with piezoelectric sensors

Real time assessment of smart concrete inspection with piezoelectric sensors

Utilization of an Electromechanical impedance (EMI) technique with Piezoelectric (PZT) sensors has showed potential for Structural Health Monitoring (SHM). The changes in mechanical structure via flexural bending and cracking can be detected by monitoring the deviations in electrical impedance signa...

Full description

Bibliographic Details
Main Authors:	Quah, Noel Tan Kai, Vo, Tran Vy Khanh, Tay, Daniel Yi Wei, Tan, Ming Jen, Wong, Teck Neng, Li, Holden King Ho
Other Authors:	School of Mechanical and Aerospace Engineering
Format:	Journal Article
Language:	English
Published:	2024
Subjects:	Engineering::Mechanical engineering Concrete 3D Printing Piezoelectric Sensor
Online Access:	https://hdl.handle.net/10356/173144

Similar Items

Sustainable support material for overhang printing in 3D concrete printing technology
by: Ting, Andrew Guan Heng, et al.
Published: (2024)

All 3D printed stretchable piezoelectric nanogenerator for self-powered sensor application
by: Zhou, Xinran, et al.
Published: (2021)

Concrete 3D printing: process parameters for process control, monitoring and diagnosis in automation and construction
by: Quah, Noel Tan Kai, et al.
Published: (2023)

Comprehensive investigations on the relationship between the 3D concrete printing failure criterion and properties of fresh-state cementitious materials
by: Liu, Zhenbang, et al.
Published: (2023)

Analysis of interactions between frictional contact and operating conditions in piezoelectric stick-slip actuator
by: Berry, Dipika, et al.
Published: (2025)

Measurement of tensile bond strength of 3D printed geopolymer mortar
by: Panda, Biranchi, et al.
Published: (2018)

Synchronized concrete and bonding agent deposition system for interlayer bond strength enhancement in 3D concrete printing
by: Weng, Yiwei, et al.
Published: (2021)

Comparative economic, environmental and productivity assessment of a concrete bathroom unit fabricated through 3D printing and a precast approach
by: Weng, Yiwei, et al.
Published: (2021)

Progressing towards high performance non-resonant piezoelectric stepping actuators
by: Berry, Dipika, et al.
Published: (2023)

Potentials And Challenges In 3D Concrete Printing
by: Wolfs, R. J. M., et al.
Published: (2016)

Extrudable region parametrical study of 3D printable concrete using recycled glass concrete
by: Ting, Andrew Guan Heng, et al.
Published: (2022)

Vision feedback on freeform-shaped structure for 3D printing
by: Quah, Noel Tan Kai
Published: (2024)

Promoting piezoelectricity in amino acids by fluorination
by: Hu, Tan, et al.
Published: (2025)

Determine the effects of pore properties on the mechanical performances of 3D concrete printing units with experimental and numerical methods
by: Liu, Zhenbang, et al.
Published: (2024)

All 3D-printed stretchable piezoelectric nanogenerator with non-protruding kirigami structure
by: Zhou, Xinran, et al.
Published: (2021)

Fresh and hardened properties of 3D printable cementitious materials for building and construction
by: Paul, Suvash Chandra, et al.
Published: (2019)

3D printing of microfludic sensor for soft robots: a preliminary study in design and fabrication
by: Goh, Guo Liang, et al.
Published: (2016)

A wearable pneumatic-piezoelectric system for quantitative assessment of skeletomuscular biomechanics
by: Gao, Dace, et al.
Published: (2024)

Improving flexural characteristics of 3D printed geopolymer composites with in-process steel cable reinforcement
by: Lim, Jian Hui, et al.
Published: (2018)

Carbon sequestration with 3D concrete printing: potentials and challenges
by: Lim, Sean Gip, et al.
Published: (2025)

Progress in construction automation : review on 3D printing of concrete materials
by: Tay, Daniel Yi Wei, et al.
Published: (2021)

Improving surface finish quality in extrusion-based 3D concrete printing using machine learning-based extrudate geometry control
by: Lao, Wenxin, et al.
Published: (2021)

3D printing trends in building and construction industry: a review
by: Tay, Yi Wei Daniel, et al.
Published: (2018)

Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concrete printing
by: Panda, Biranchi, et al.
Published: (2019)

Axial performances of the steel rebar reinforced column confined by the steel cable reinforced 3D concrete printing permanent formwork
by: Liu, Zhenbang, et al.
Published: (2024)

Effect of nanostructured silica additives on the extrusion-based 3D concrete printing application
by: Liu, Zhenbang, et al.
Published: (2023)

Extracting BIM information for lattice toolpath planning in digital concrete printing with developed dynamo script : a case study
by: Weng, Yiwei, et al.
Published: (2021)

3D Printing for Sustainable Construction
by: Tay, Daniel Yi Wei, et al.
Published: (2021)

Development of ductile concrete for visual sensor enabled 3D-printing
by: Lim, Rae-Anne Ying
Published: (2024)

Current challenges and future potential of 3D concrete printing
by: Panda, Biranchi, et al.
Published: (2019)

Rheological behavior of high volume fly ash mixtures containing micro silica for digital construction application
by: Panda, Branchi, et al.
Published: (2021)

Carbon capture and sequestration with in-situ CO2 and steam integrated 3D concrete printing
by: Lim, Sean Gip, et al.
Published: (2024)

Utilization of recycled glass for 3D concrete printing : rheological and mechanical properties
by: Ting, Andrew Guan Heng, et al.
Published: (2020)

Lifestyle Product Via 3D Printing: Wearable Fashion
by: Yap, Yee Ling, et al.
Published: (2016)

The effect of material fresh properties and process parameters on buildability and interlayer adhesion of 3D printed concrete
by: Panda, Biranchi, et al.
Published: (2019)

Metallic nanoparticle inks for 3D printing of electronics
by: Tan, Hong Wei, et al.
Published: (2020)

Time gap effect on bond strength of 3D-printed concrete
by: Tay, Daniel Yi Wei, et al.
Published: (2020)

Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay
by: Panda, Biranchi, et al.
Published: (2020)

Proof-of-concept: 3D bioprinting of pigmented human skin constructs
by: Ng, Wei Long, et al.
Published: (2018)

Development of novel concave and convex trowels for higher interlayer strength of 3D printed cement paste
by: He, Lewei, et al.
Published: (2024)