Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel.
The objective of this research is to characterize mechanical and physical behaviors of adhesives bonding (butt and lap joints) on mild carbon steel. The research used an adhesive material of devcon plastic steel. Mechanical properties are tensile strength, shear strength and toughness of the joints....
| Main Author: | |
|---|---|
| Format: | Article |
| Published: |
[Yogyakarta] : Universitas Gadjah Mada
2003
|
| Subjects: |
| _version_ | 1797018747016314880 |
|---|---|
| author | Perpustakaan UGM, i-lib |
| author_facet | Perpustakaan UGM, i-lib |
| author_sort | Perpustakaan UGM, i-lib |
| collection | UGM |
| description | The objective of this research is to characterize mechanical and physical behaviors of adhesives bonding (butt and lap joints) on mild carbon steel. The research used an adhesive material of devcon plastic steel. Mechanical properties are tensile strength, shear strength and toughness of the joints.
The major parameters of this research were adherends surface roughness Ra, adhesive thickness, curing time and curing temperature. Surface roughness of the carbon steel adherends are Ra = 0,52 pm, 0,76 11/71 and 1,21 pin. Adhesive thickness vary from: 0,03 mm to 0,3 mm and curing time: 1, 2, 3, 4 hours at curing temperatures: 55, 70, 85, 100, 120 and 140 °C. The research has been conducted under static loads at room temperature.
The results of static loads (tensile and shear loads) show that adhesive thickness and adherends surface roughness influence significantly the strength and toughness of the joints. An increase in the adherends surface roughness will increase adhesive strengths. For certain surface roughness, the joints have an optimum adhesive thickness that produces a strength and toughness maximum. Heat treatment of the joints at curing temperature for certain curing time influences significantly shear stresses. An increase of curing time will increase shear stresses. At certain surface roughness and curing time (for example: Ra = 0,76 pm and curing time = 4 hours), this research shows that the joints have an optimum curing temperature. Specimens cured at elevated temperature show generally the increasing strength, however there is an optimum temperature where cure exceed this temperature the strength begins decrease. Adhesives bonding failure of butt joints are generally cohesive and lap joints have a mixed failure cohesive and adhesive.
Keywords: adhesive bonding, mild carbon steel, devcon plastic steel, static load, butt joints. |
| first_indexed | 2024-03-05T23:03:09Z |
| format | Article |
| id | oai:generic.eprints.org:22895 |
| institution | Universiti Gadjah Mada |
| last_indexed | 2024-03-13T18:48:57Z |
| publishDate | 2003 |
| publisher | [Yogyakarta] : Universitas Gadjah Mada |
| record_format | dspace |
| spelling | oai:generic.eprints.org:228952014-06-18T00:29:45Z https://repository.ugm.ac.id/22895/ Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. Perpustakaan UGM, i-lib Jurnal i-lib UGM The objective of this research is to characterize mechanical and physical behaviors of adhesives bonding (butt and lap joints) on mild carbon steel. The research used an adhesive material of devcon plastic steel. Mechanical properties are tensile strength, shear strength and toughness of the joints. The major parameters of this research were adherends surface roughness Ra, adhesive thickness, curing time and curing temperature. Surface roughness of the carbon steel adherends are Ra = 0,52 pm, 0,76 11/71 and 1,21 pin. Adhesive thickness vary from: 0,03 mm to 0,3 mm and curing time: 1, 2, 3, 4 hours at curing temperatures: 55, 70, 85, 100, 120 and 140 °C. The research has been conducted under static loads at room temperature. The results of static loads (tensile and shear loads) show that adhesive thickness and adherends surface roughness influence significantly the strength and toughness of the joints. An increase in the adherends surface roughness will increase adhesive strengths. For certain surface roughness, the joints have an optimum adhesive thickness that produces a strength and toughness maximum. Heat treatment of the joints at curing temperature for certain curing time influences significantly shear stresses. An increase of curing time will increase shear stresses. At certain surface roughness and curing time (for example: Ra = 0,76 pm and curing time = 4 hours), this research shows that the joints have an optimum curing temperature. Specimens cured at elevated temperature show generally the increasing strength, however there is an optimum temperature where cure exceed this temperature the strength begins decrease. Adhesives bonding failure of butt joints are generally cohesive and lap joints have a mixed failure cohesive and adhesive. Keywords: adhesive bonding, mild carbon steel, devcon plastic steel, static load, butt joints. [Yogyakarta] : Universitas Gadjah Mada 2003 Article NonPeerReviewed Perpustakaan UGM, i-lib (2003) Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. Jurnal i-lib UGM. http://i-lib.ugm.ac.id/jurnal/download.php?dataId=5821 |
| spellingShingle | Jurnal i-lib UGM Perpustakaan UGM, i-lib Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title | Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title_full | Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title_fullStr | Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title_full_unstemmed | Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title_short | Characterization of Devcon Plastic Steel Adhesive on Mild Carbon Steel. |
| title_sort | characterization of devcon plastic steel adhesive on mild carbon steel |
| topic | Jurnal i-lib UGM |
| work_keys_str_mv | AT perpustakaanugmilib characterizationofdevconplasticsteeladhesiveonmildcarbonsteel |