Nanopillar Array for Cell Culture Dish

Nanopillar Array for Cell Culture Dish

Bibliographic Details
Main Author:	Ali, Mohammad Yeakub
Format:	Proceeding Paper
Language:	English
Published:	2011
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/2532/1/FIB_Cell_Culture_DUET_%2816_June_2011%29.pdf

Similar Items

Fabrication of silicon nanopillar sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Fabrication of Micropillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

Rheological and thermal behaviour of high impact polystyrene nanocomposite
by: Al-Ghamdi, Ahmed S., et al.
Published: (2012)

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel
by: Afifah, Ali, et al.
Published: (2010)

Investigation of microholes produced by focused ion beam micromachining
by: Mohd Fuad, Nurul Hajar, et al.
Published: (2011)

Investigation of Microholes Produced by Focused Ion Beam Micromachining
by: Mohd. Fuad, Nurul Hajar, et al.
Published: (2010)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Investigation of recast layer of non-conductive ceramic due to micro-EDM
by: Mohamed, Abd. Rahman, et al.
Published: (2014)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

A review of focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2012)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Investigation of material removal characteristics in EDM of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2013)

Minimum chip thickness in machining MEMS structure using Tool Based Micromilling
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Investigation of burr in high speed microdrilling
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic
by: Moudood, M. A., et al.
Published: (2014)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Threat assessment analysis for vehicle collision avoidance
by: Mohammad Izzad, Mohammad Idzlaluddin
Published: (2017)

An MPPT controller with a modified four-leg interleaved DC/DC boost converter for fuel cell applications
by: Veerendra, Arigela Satya, et al.
Published: (2025)

Performance evaluation of wire electrode discharge machining (WEDM) On Inconel 718
by: Ali, Mohd. Nizam
Published: (2010)

Surface integrity of Inconel 718 during drilling operation
by: Farid, Ali Akhavan
Published: (2008)

Experimental and Simulation Approach; Investigation Effect of Axial Feed Rate to the Cutting Force in Dimple Milling Using Ball End Mill Tool
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2023)

Enhancement of machinability of Inconel 718 in end milling through online induction heating of workpiece
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Multi-objectives process optimization in end milling process of aluminium alloy 6061-T6 using genetic algorithm
by: W., Safiei, et al.
Published: (2024)

Preliminary Investigation of an Innovative Digital Motion Analysis Device for Badminton Athlete Performance Evaluation
by: Zahari, Taha, et al.
Published: (2016)

Characterization of Blended Biodiesel Fuel Properties with Small Portion of Butanol as a Fuel Additive
by: Obed M., Ali, et al.
Published: (2014)

Fatigue and harmonic analysis of a diesel engine Crankshaft using ANSYS
by: Muhammad, Aisha, et al.
Published: (2019)

Influence of cutting parameters to surface area roughness in dimple machining using milling process
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2021)

Human-like driver model for emergency collision avoidance using neural network autoregressive with exogenous inputs
by: Nurhaffizah, Hassan, et al.
Published: (2024)

Comparison of uncoated and coated carbide inserts in end milling of Ti–6Al–4V in terms of surface roughness
by: Hossain, Mohammad Ishtiaq, et al.
Published: (2008)

Wear Behaviour of Tungsten Carbide in End Milling Process of Aluminium Alloy 6061-T6 with Minimal Quantity of Tri-hybrid Nanofluids
by: W., Safiei, et al.
Published: (2023)

Water absorption behaviour on the mechanical properties of woven hybrid reinforced polyester composites
by: Mohammad Hazim, Mohamad Hamdan, et al.
Published: (2019)

Historical development of hybrid materials
by: M. R. M., Rejab, et al.
Published: (2020)

Extension of the displacement method by measuring reference pieces using multiple sensors for on-machine surface profile measurement
by: Haramiishi, Y., et al.
Published: (2024)