Constructal theory of the minimum requirements for forced convection cooling solutions

Constructal theory of the minimum requirements for forced convection cooling solutions

The advances in microfluidics and microelectronics bring with them the need to provide new cooling solutions for many applications. A number of technologies are under development for forced convection cooling at the microscale. This short paper, through the new constructal theory of Bejan, presents...

Descrizione completa

Dettagli Bibliografici
Autori principali:	Walsh, E, Grimes, R, ASME
Natura:	Conference item
Pubblicazione:	2005

Documenti analoghi

An experimental study on the performance of miniature heat sinks for forced convection air cooling
di: Egan, V, et al.
Pubblicazione: (2008)

Optimization study for forced-convective cooling of an augmented printed-circuit-board surface with minimum pumping power
di: Tan, Seng Sing
Pubblicazione: (2005)

An Experimental Study on the Design of Miniature Heat Sinks for Forced Convection Air Cooling
di: Egan, V, et al.
Pubblicazione: (2009)

Forced-convection, liquid-cooled, microchannel heat sinks
di: Phillips, Richard J
Pubblicazione: (2005)

Acoustic Emissions From Active Cooling Solutions for Portable Devices
di: Walsh, E, et al.
Pubblicazione: (2009)

The development of an integrated fan and heat sink solution for thermal management in low profile applications
di: Walsh, E, et al.
Pubblicazione: (2006)

FINLESS heat sinks, high performance and low cost for low profile cooling applications
di: Walsh, E, et al.
Pubblicazione: (2012)

Flow distribution measurements from an air cooled condenser in a similar to 400MW power plant
di: Walsh, E, et al.
Pubblicazione: (2012)

Acoustic emissions from active cooling solutions for portable devices
di: Walsh, E, et al.
Pubblicazione: (2008)

Forced convection condensation in novel air-cooled fin tubes
di: Tan, Timothy Tze Yuan
Pubblicazione: (2021)

PIV measurements of the effects of geometric scale on electronics cooling axial fan flow
di: Grimes, R, et al.
Pubblicazione: (2007)

Study of Forced Convection Nanofluid Heat Transfer in the Automotive Cooling System
di: K., Kadirgama, et al.
Pubblicazione: (2014)

A minimum energy solution for muscle force control during walking.
di: Hardt, D. E. (David E.)
Pubblicazione: (2005)

Analysis of forced convection degraded core cooling in light water reactors
di: Mohammed, S. M., et al.
Pubblicazione: (2014)

Cooling enhancement of forced convection air cooled chip array through active and passive flow modulation
di: Ratts, Eric B. (Eric Bradley), 1963-
Pubblicazione: (2005)

Forced convective heat transfer to supercritical water in micro-rocket cooling passages
di: Faust, Adriane (Adriane Jean), 1976-
Pubblicazione: (2005)

Active cooling of a mobile phone handset
di: Grimes, R, et al.
Pubblicazione: (2010)

Forced convection and sub-cooled flow boiling heat transfer from electronic chips
di: Tou, Kwok Woon., et al.
Pubblicazione: (2008)

The performance of active cooling in a mobile phone
di: Walsh, E, et al.
Pubblicazione: (2008)

The theory of electrodeposition in the presence of forced convection: transport controlled nucleation of hemispheres
di: Hyde, M, et al.
Pubblicazione: (2002)

A. micromixer based upon buoyancy
di: Walsh, E, et al.
Pubblicazione: (2005)

Application of constructal theory to prediction of boundary layer transition onset
di: Walsh, E, et al.
Pubblicazione: (2006)

Minimum requirements for ookinete to oocyst transformation in Plasmodium.
di: Carter, V, et al.
Pubblicazione: (2007)

Dual solutions on thermosolutal marangoni forced convection boundary layer with suction and injection
di: Abdul Hamid, Rohana, et al.
Pubblicazione: (2011)

An experimental characterisation of miniature scale cold plates for electronics cooling applications
di: Jeffers, N, et al.
Pubblicazione: (2007)

ON THE PERFORMANCE OF MINIATURE CENTRIFUGAL FANS WITH VARYING BLADE CORD LENGTH
di: Walsh, P, et al.
Pubblicazione: (2008)

Minimum Exergy Requirements for the Manufacturing of Carbon Nanotubes
di: Gutowski, Timothy G., et al.
Pubblicazione: (2011)

Numerical Study on Turbulent Forced Convective Heat Transfer Using Nanofluids TiO2 in an Automotive Cooling System
di: Adnan M., Husein, et al.
Pubblicazione: (2017)

Forced Convection Heat Transfer Using Water-Ethylene Glycol (60:40) Based Nanofluids in Automotive Cooling System
di: N. A., Usri, et al.
Pubblicazione: (2015)

Finless heat sinks, high performance and low cost for low profile cooling applications
di: Walsh, E, et al.
Pubblicazione: (2013)

Forced-convection condensation inside tubes
di: Traviss, Donald P., et al.
Pubblicazione: (2011)

Minimum hardware requirements for hybrid quantum-classical DMFT
di: Jaderberg, B, et al.
Pubblicazione: (2020)

Two-facility location games with minimum distance requirement
di: Xu, Xinping, et al.
Pubblicazione: (2022)

Forced-convection, dispersed-flow film boiling
di: Hynek, Scott Josef, et al.
Pubblicazione: (2011)

Experimental electrical characterisation of thermoelectric generator using forced convection water cooling / Raihan Abu Bakar...[et al.]
di: Abu Bakar, Raihan, et al.
Pubblicazione: (2020)

Turbulent forced convection in channels and bundles : theory and applications to heat exchangers and nuclear reactors/
di: NATO Advanced Study Institute. Conference on Turbulent Forced Convection in Channels and Bundles (1978 : Istanbul), et al.
Pubblicazione: (1979)

Micro-piv measurements of flowfields within plugs in two phase flows for mu-TAS applications
di: King, C, et al.
Pubblicazione: (2006)

THERMAL PERFORMANCE OF TWO AND THREE DIMENSIONAL RADIAL FLOW HEAT SINKS
di: Grimes, R, et al.
Pubblicazione: (2009)

Influence of the Flow from an Axial Fan on the Performance of a Heat Exchanger
di: Moore, J, et al.
Pubblicazione: (2012)

Multiscale design and optimisation of a radial flow heatsink
di: Hanly, K, et al.
Pubblicazione: (2006)