Reconstruction of axisymmetric strain distributions via neutron strain tomography

Reconstruction of axisymmetric strain distributions via neutron strain tomography

Predicting the behaviour of structural components under a particular set of loading conditions requires knowledge of the residual elastic strain distribution throughout the bulk of these components. Characterising the 3D strain state at any particular point involves the measurement of six independen...

Descrizione completa

Dettagli Bibliografici
Autori principali:	Abbey, B, Zhang, S, Vorster, W, Korsunsky, A
Natura:	Journal article
Lingua:	English
Pubblicazione:	2012

Documenti analoghi

Feasibility study of neutron strain tomography
di: Abbey, B, et al.
Pubblicazione: (2009)

Neutron strain tomography
di: Abbey, B
Pubblicazione: (2012)

Neutron strain tomography using Bragg-edge transmission
di: Abbey, B, et al.
Pubblicazione: (2012)

Neutron strain tomography using Bragg-edge transmission
di: Abbey, B, et al.
Pubblicazione: (2012)

The Principle of Strain Reconstruction Tomography: Determination of Quench Strain Distribution from Diffraction Measurements
di: Korsunsky, A, et al.
Pubblicazione: (2005)

The principle of strain reconstruction tomography: determination of quench strain distribution from diffraction measurements
di: Korsunsky, A, et al.
Pubblicazione: (2006)

Materials Structure and Strain Analysis Using Time-of-flight Neutron Diffraction
di: Zhang, S, et al.
Pubblicazione: (2009)

A study of residual elastic strain distribution in an AZ91 Mg alloy bar loaded in four point bending
di: Prakash, D, et al.
Pubblicazione: (2008)

A study of residual elastic strain distribution in an AZ91 Mg alloy bar loaded in four point bending
di: Prakash, D, et al.
Pubblicazione: (2008)

Analysis of residual strain and stress states due to heat treatment and thermal processing
di: Vorster, W, et al.
Pubblicazione: (2009)

Recovering the second moment of the strain distribution from neutron Bragg edge data
di: Fogarty, K, et al.
Pubblicazione: (2022)

Neutron diffraction measurement and finite element modelling of residual strains due to bath and spray quenching of AISI 316L stainless steel cylinders
di: Vorster, W, et al.
Pubblicazione: (2008)

Neutron diffraction measurement and finite element modelling of residual strains due to bath and spray quenching of AISI 316L stainless steel cylinders
di: Vorster, W, et al.
Pubblicazione: (2008)

Strain tomography of polycrystalline zirconia dental prostheses by synchrotron X-ray diffraction
di: Korsunsky, A, et al.
Pubblicazione: (2011)

Strain mapping and defects inspection of divertor targets by Bragg edge neutron imaging and neutron tomography
di: Triestino Minniti, et al.
Pubblicazione: (2025-01-01)

Solution of axisymmetric crack problems using distributed dislocation ring dipoles
di: Korsunsky, A, et al.
Pubblicazione: (2000)

Solution of axisymmetric crack problems using distributed dislocation ring dipoles
di: Korsunsky, A, et al.
Pubblicazione: (2000)

Evaluation of residual stresses and strains using the Eigenstrain Reconstruction Method
di: Jun, T, et al.
Pubblicazione: (2010)

Evaluation of residual stresses and strains using the Eigenstrain Reconstruction Method
di: Jun, T, et al.
Pubblicazione: (2010)

High-energy synchrotron X-ray analysis of residual plastic strains induced in shot-peened steel plates
di: Zhang, S, et al.
Pubblicazione: (2008)

Triaxial residual strains in a railway rail measured by neutron diffraction
di: Jun, T, et al.
Pubblicazione: (2009)

Fundamental eigenstrain solutions for axisymmetric crack problems
di: Korsunsky, A
Pubblicazione: (1995)

FUNDAMENTAL EIGENSTRAIN SOLUTIONS FOR AXISYMMETRICAL CRACK PROBLEMS
di: Korsunsky, A
Pubblicazione: (1995)

Neutron strain scanning for experimental validation of the artificial intelligence based eigenstrain contour method
di: Uzun, F, et al.
Pubblicazione: (2020)

A beam-bending eigenstrain analysis of residual elastic strains in multi-scan laser-formed steel samples
di: Korsunsky, A, et al.
Pubblicazione: (2008)

A beam-bending eigenstrain analysis of residual elastic strains in multi-scan laser-formed steel samples
di: Korsunsky, A, et al.
Pubblicazione: (2008)

Energy Resolved Neutron Imaging for Strain Reconstruction Using the Finite Element Method
di: Riya Aggarwal, et al.
Pubblicazione: (2020-03-01)

The solution of crack problems by using distributed strain nuclei
di: Korsunsky, A, et al.
Pubblicazione: (1996)

Multi-scan laser forming: synchrotron strain scanning and microstructure evolution
di: Topic, M, et al.
Pubblicazione: (2007)

Evaluation of the overload effect on fatigue crack growth with the help of synchrotron XRD strain mapping
di: Belnoue, J, et al.
Pubblicazione: (2010)

Influence of the form of axisymmetric load on the stress-strain state of an elastoplastic half-space
di: Ogar Peter, et al.
Pubblicazione: (2019-01-01)

An Investigation of Radial Basis Function Method for Strain Reconstruction by Energy-Resolved Neutron Imaging
di: Riya Aggarwal, et al.
Pubblicazione: (2021-01-01)

Residual elastic strain due to laser shock peening: modelling by eigenstrain distribution
di: Korsunsky, A
Pubblicazione: (2006)

Residual elastic strain due to laser shock peening: modelling by eigenstrain distribution
di: Korsunsky, A
Pubblicazione: (2006)

Enhanced Stretchable and Sensitive Strain Sensor via Controlled Strain Distribution
di: Huamin Chen, et al.
Pubblicazione: (2020-01-01)

From x-ray telescopes to neutron scattering: Using axisymmetric mirrors to focus a neutron beam
di: Khaykovich, Boris, et al.
Pubblicazione: (2011)

Measurement of residual elastic strains in a titanium alloy using high energy synchrotron X-ray diffraction
di: Korsunsky, A, et al.
Pubblicazione: (2006)

Improved Acquisition and Reconstruction for Wavelength-Resolved Neutron Tomography
di: Singanallur Venkatakrishnan, et al.
Pubblicazione: (2021-01-01)

Demonstration of achromatic cold-neutron microscope utilizing axisymmetric focusing mirrors
di: Liu, Dazhi, et al.
Pubblicazione: (2013)

High quality reconstruction for neutron computerized tomography images
di: Salwa R. Soliman, et al.
Pubblicazione: (2021-04-01)