Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Detalhes bibliográficos
Principais autores:	Gerlach, R, Siviour, C, Petrinic, N, Wiegand, J, EDPS
Formato:	Conference item
Publicado em:	2009

Registros relacionados

Strain rate dependence of a super-elastic NiTi alloy
por: Siviour, C, et al.
Publicado em: (2009)

An integrated experimental-numerical method for characterisation of materials at high strain rates
por: Elliott, B, et al.
Publicado em: (2007)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
por: Gerlach, R, et al.
Publicado em: (2013)

In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
por: Gerlach, R, et al.
Publicado em: (2012)

Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading
por: Gerlach, R, et al.
Publicado em: (2008)

Strain rate dependence of Ti64: Characterisation of mechanical properties up to failure using novel optical techniques
por: Arthington, M, et al.
Publicado em: (2009)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
por: Pathan, MV, et al.
Publicado em: (2018)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
por: Pathan Mehtab V., et al.
Publicado em: (2018-01-01)

On the rate dependent behaviour of epoxy adhesive joints: Experimental characterisation and modelling of mode I failure
por: Lissner, M, et al.
Publicado em: (2018)

Improved materials characterisation through the application of geometry reconstruction to quasi-static and high-strain-rate tension tests
por: Arthington, M, et al.
Publicado em: (2012)

Experimentally characterising the temperature and rate dependent behaviour of unfilled, and glass microsphere filled, natural rubber
por: Trivedi, A, et al.
Publicado em: (2023)

Experimental Characterisation of Aluminium 6082 at Varying Temperature and Strain Rate
por: Lemanski, S, et al.
Publicado em: (2013)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
por: Wielewski, E, et al.
Publicado em: (2009)

Experimental characterisation and modelling of the strain rate dependent mechanical response of a filled thermo-reversible supramolecular polyurethane
por: Chen, H, et al.
Publicado em: (2022)

Taylor impact experiments on Ti-6Al-4V specimens using 3D geometry reconstruction and instrumented target rods
por: Wielewski, E, et al.
Publicado em: (2009)

Characterisation of damage mechanisms in oxide ceramics indented at dynamic and quasi-static strain rates
por: Dancer, C, et al.
Publicado em: (2019)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
por: Li, P, et al.
Publicado em: (2009)

Rate dependent non-linear mechanical behaviour of continuous fibre-reinforced thermoplastic composites – Experimental characterisation and viscoelastic-plastic damage modelling
por: Matthias Zscheyge, et al.
Publicado em: (2020-08-01)

Compressive deformation of Rohacell foams: Effects of strain rate and temperature
por: Arezoo, S, et al.
Publicado em: (2013)

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain
por: Xu, Y, et al.
Publicado em: (2022)

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites
por: Chen, Y, et al.
Publicado em: (2023)

An experimental investigation of rate-dependent deformation and failure of three titanium alloys
por: Sarsfield, H, et al.
Publicado em: (2007)

High strain rate characterisation of a polymer bonded sugar
por: Laity, P, et al.
Publicado em: (2006)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
por: Trivedi, AR, et al.
Publicado em: (2021)

Experimentally simulating adiabatic behaviour: capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
por: Trivedi, AR, et al.
Publicado em: (2022)

The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments
por: Li, P, et al.
Publicado em: (2009)

On the correlation between macrozones and twinning in Ti-6Al-4V at very high strain rates
por: Wielewski, E, et al.
Publicado em: (2012)

Pressure and temperature dependent dynamic flow and failure behavior of PMMA at intermediate strain rates
por: Zhang, L, et al.
Publicado em: (2021)

Mechanical behaviour of polymers at high rates of strain
por: Siviour, C, et al.
Publicado em: (2006)

Experimentally simulating adiabatic behaviour: Capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
por: Akash R. Trivedi, et al.
Publicado em: (2022-12-01)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
por: Trivedi Akash R, et al.
Publicado em: (2021-01-01)

Damage formation during high strain rate deformation of PBS9501
por: Siviour, C, et al.
Publicado em: (2007)

A three-dimensional progressive damage model for fibre-composite materials
por: Sosa, J, et al.
Publicado em: (2008)

Characterisation of the high strain rate behaviour of tubular materials
por: Caisso Camille, et al.
Publicado em: (2018-01-01)

Microstructure and x-ray microtomographic characterisation of deformation in electrodeposited nickel thin-walled hollow spheres
por: Li, P, et al.
Publicado em: (2013)

The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride
por: Siviour, C, et al.
Publicado em: (2005)

Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloys: Experiments and modelling
por: Zhang, L, et al.
Publicado em: (2019)

An algorithm for determination of the fracture angle for the three-dimensional Puck matrix failure criterion for UD composites
por: Wiegand, J, et al.
Publicado em: (2008)

Strain rate dependent constitutive modelling of 3D printed polymers
por: Lißner, M, et al.
Publicado em: (2021)

Strain Rate Dependent Constitutive Modelling of 3D Printed Polymers
por: Lißner Maria, et al.
Publicado em: (2021-01-01)