Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Detalles Bibliográficos
Main Authors:	Gerlach, R, Siviour, C, Petrinic, N, Wiegand, J, EDPS
Formato:	Conference item
Publicado:	2009

Títulos similares

Strain rate dependence of a super-elastic NiTi alloy
por: Siviour, C, et al.
Publicado: (2009)

An integrated experimental-numerical method for characterisation of materials at high strain rates
por: Elliott, B, et al.
Publicado: (2007)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
por: Gerlach, R, et al.
Publicado: (2013)

In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
por: Gerlach, R, et al.
Publicado: (2012)

Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading
por: Gerlach, R, et al.
Publicado: (2008)

Strain rate dependence of Ti64: Characterisation of mechanical properties up to failure using novel optical techniques
por: Arthington, M, et al.
Publicado: (2009)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
por: Pathan, MV, et al.
Publicado: (2018)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
por: Pathan Mehtab V., et al.
Publicado: (2018-01-01)

On the rate dependent behaviour of epoxy adhesive joints: Experimental characterisation and modelling of mode I failure
por: Lissner, M, et al.
Publicado: (2018)

Improved materials characterisation through the application of geometry reconstruction to quasi-static and high-strain-rate tension tests
por: Arthington, M, et al.
Publicado: (2012)

Experimentally characterising the temperature and rate dependent behaviour of unfilled, and glass microsphere filled, natural rubber
por: Trivedi, A, et al.
Publicado: (2023)

Experimental Characterisation of Aluminium 6082 at Varying Temperature and Strain Rate
por: Lemanski, S, et al.
Publicado: (2013)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
por: Wielewski, E, et al.
Publicado: (2009)

Experimental characterisation and modelling of the strain rate dependent mechanical response of a filled thermo-reversible supramolecular polyurethane
por: Chen, H, et al.
Publicado: (2022)

Taylor impact experiments on Ti-6Al-4V specimens using 3D geometry reconstruction and instrumented target rods
por: Wielewski, E, et al.
Publicado: (2009)

Characterisation of damage mechanisms in oxide ceramics indented at dynamic and quasi-static strain rates
por: Dancer, C, et al.
Publicado: (2019)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
por: Li, P, et al.
Publicado: (2009)

Rate dependent non-linear mechanical behaviour of continuous fibre-reinforced thermoplastic composites – Experimental characterisation and viscoelastic-plastic damage modelling
por: Matthias Zscheyge, et al.
Publicado: (2020-08-01)

Compressive deformation of Rohacell foams: Effects of strain rate and temperature
por: Arezoo, S, et al.
Publicado: (2013)

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain
por: Xu, Y, et al.
Publicado: (2022)

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites
por: Chen, Y, et al.
Publicado: (2023)

An experimental investigation of rate-dependent deformation and failure of three titanium alloys
por: Sarsfield, H, et al.
Publicado: (2007)

High strain rate characterisation of a polymer bonded sugar
por: Laity, P, et al.
Publicado: (2006)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
por: Trivedi, AR, et al.
Publicado: (2021)

Experimentally simulating adiabatic behaviour: capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
por: Trivedi, AR, et al.
Publicado: (2022)

The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments
por: Li, P, et al.
Publicado: (2009)

On the correlation between macrozones and twinning in Ti-6Al-4V at very high strain rates
por: Wielewski, E, et al.
Publicado: (2012)

Pressure and temperature dependent dynamic flow and failure behavior of PMMA at intermediate strain rates
por: Zhang, L, et al.
Publicado: (2021)

Mechanical behaviour of polymers at high rates of strain
por: Siviour, C, et al.
Publicado: (2006)

Experimentally simulating adiabatic behaviour: Capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
por: Akash R. Trivedi, et al.
Publicado: (2022-12-01)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
por: Trivedi Akash R, et al.
Publicado: (2021-01-01)

Damage formation during high strain rate deformation of PBS9501
por: Siviour, C, et al.
Publicado: (2007)

A three-dimensional progressive damage model for fibre-composite materials
por: Sosa, J, et al.
Publicado: (2008)

Characterisation of the high strain rate behaviour of tubular materials
por: Caisso Camille, et al.
Publicado: (2018-01-01)

Microstructure and x-ray microtomographic characterisation of deformation in electrodeposited nickel thin-walled hollow spheres
por: Li, P, et al.
Publicado: (2013)

The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride
por: Siviour, C, et al.
Publicado: (2005)

Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloys: Experiments and modelling
por: Zhang, L, et al.
Publicado: (2019)

An algorithm for determination of the fracture angle for the three-dimensional Puck matrix failure criterion for UD composites
por: Wiegand, J, et al.
Publicado: (2008)

Strain rate dependent constitutive modelling of 3D printed polymers
por: Lißner, M, et al.
Publicado: (2021)

Strain Rate Dependent Constitutive Modelling of 3D Printed Polymers
por: Lißner Maria, et al.
Publicado: (2021-01-01)