Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites

Bibliografske podrobnosti
Main Authors:	Gerlach, R, Siviour, C, Petrinic, N, Wiegand, J, EDPS
Format:	Conference item
Izdano:	2009

Podobne knjige/članki

Strain rate dependence of a super-elastic NiTi alloy
od: Siviour, C, et al.
Izdano: (2009)

An integrated experimental-numerical method for characterisation of materials at high strain rates
od: Elliott, B, et al.
Izdano: (2007)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
od: Gerlach, R, et al.
Izdano: (2013)

In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
od: Gerlach, R, et al.
Izdano: (2012)

Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading
od: Gerlach, R, et al.
Izdano: (2008)

Strain rate dependence of Ti64: Characterisation of mechanical properties up to failure using novel optical techniques
od: Arthington, M, et al.
Izdano: (2009)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
od: Pathan, MV, et al.
Izdano: (2018)

Experimental characterisation of rate-dependent compression behaviour of fibre reinforced composites
od: Pathan Mehtab V., et al.
Izdano: (2018-01-01)

On the rate dependent behaviour of epoxy adhesive joints: Experimental characterisation and modelling of mode I failure
od: Lissner, M, et al.
Izdano: (2018)

Improved materials characterisation through the application of geometry reconstruction to quasi-static and high-strain-rate tension tests
od: Arthington, M, et al.
Izdano: (2012)

Experimentally characterising the temperature and rate dependent behaviour of unfilled, and glass microsphere filled, natural rubber
od: Trivedi, A, et al.
Izdano: (2023)

Experimental Characterisation of Aluminium 6082 at Varying Temperature and Strain Rate
od: Lemanski, S, et al.
Izdano: (2013)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
od: Wielewski, E, et al.
Izdano: (2009)

Experimental characterisation and modelling of the strain rate dependent mechanical response of a filled thermo-reversible supramolecular polyurethane
od: Chen, H, et al.
Izdano: (2022)

Taylor impact experiments on Ti-6Al-4V specimens using 3D geometry reconstruction and instrumented target rods
od: Wielewski, E, et al.
Izdano: (2009)

Characterisation of damage mechanisms in oxide ceramics indented at dynamic and quasi-static strain rates
od: Dancer, C, et al.
Izdano: (2019)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
od: Li, P, et al.
Izdano: (2009)

Rate dependent non-linear mechanical behaviour of continuous fibre-reinforced thermoplastic composites – Experimental characterisation and viscoelastic-plastic damage modelling
od: Matthias Zscheyge, et al.
Izdano: (2020-08-01)

Compressive deformation of Rohacell foams: Effects of strain rate and temperature
od: Arezoo, S, et al.
Izdano: (2013)

Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain
od: Xu, Y, et al.
Izdano: (2022)

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites
od: Chen, Y, et al.
Izdano: (2023)

An experimental investigation of rate-dependent deformation and failure of three titanium alloys
od: Sarsfield, H, et al.
Izdano: (2007)

High strain rate characterisation of a polymer bonded sugar
od: Laity, P, et al.
Izdano: (2006)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
od: Trivedi, AR, et al.
Izdano: (2021)

Experimentally simulating adiabatic behaviour: capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
od: Trivedi, AR, et al.
Izdano: (2022)

The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments
od: Li, P, et al.
Izdano: (2009)

On the correlation between macrozones and twinning in Ti-6Al-4V at very high strain rates
od: Wielewski, E, et al.
Izdano: (2012)

Pressure and temperature dependent dynamic flow and failure behavior of PMMA at intermediate strain rates
od: Zhang, L, et al.
Izdano: (2021)

Mechanical behaviour of polymers at high rates of strain
od: Siviour, C, et al.
Izdano: (2006)

Experimentally simulating adiabatic behaviour: Capturing the high strain rate compressive response of polymers using low strain rate experiments with programmed temperature profiles
od: Akash R. Trivedi, et al.
Izdano: (2022-12-01)

Predicting the high strain rate behaviour of particulate composites using time-temperature superposition based modelling
od: Trivedi Akash R, et al.
Izdano: (2021-01-01)

Damage formation during high strain rate deformation of PBS9501
od: Siviour, C, et al.
Izdano: (2007)

A three-dimensional progressive damage model for fibre-composite materials
od: Sosa, J, et al.
Izdano: (2008)

Characterisation of the high strain rate behaviour of tubular materials
od: Caisso Camille, et al.
Izdano: (2018-01-01)

Microstructure and x-ray microtomographic characterisation of deformation in electrodeposited nickel thin-walled hollow spheres
od: Li, P, et al.
Izdano: (2013)

The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride
od: Siviour, C, et al.
Izdano: (2005)

Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloys: Experiments and modelling
od: Zhang, L, et al.
Izdano: (2019)

An algorithm for determination of the fracture angle for the three-dimensional Puck matrix failure criterion for UD composites
od: Wiegand, J, et al.
Izdano: (2008)

Strain rate dependent constitutive modelling of 3D printed polymers
od: Lißner, M, et al.
Izdano: (2021)

Strain Rate Dependent Constitutive Modelling of 3D Printed Polymers
od: Lißner Maria, et al.
Izdano: (2021-01-01)