Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue, creep and oxidation

Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue, creep and oxidation

Pokaži ostale verzije (1)

The objective of the present study is to review the different phenomena responsible for crack growth in the IN718 nickel-base superalloy under the combination of fatigue, creep and oxidation. We review the descriptions of the micro-mechanisms found in the literature, with a special emphasis on the t...

Bibliografski detalji
Glavni autori:	Prakash, D, Walsh, M, Maclachlan, D, Korsunsky, A
Daljnji autori:	European Structural Integrity Society
Format:	Journal article
Jezik:	English
Izdano:	Elsevier 2009
Teme:	Engineering & allied sciences

Slični predmeti

Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue, creep and oxidation
od: Prakash, D, i dr.
Izdano: (2009)

Crack tip deformation fields and fatigue crack growth rates in Ti-6Al-4V
od: Korsunsky, A, i dr.
Izdano: (2009)

Investigation of residual stress induced crack closure and its effects on fatigue in metal matrix composites
od: Korsunsky, A, i dr.
Izdano: (1997)

Comparative assessment of dissipated energy and other fatigue criteria
od: Korsunsky, A, i dr.
Izdano: (2007)

Solution of axisymmetric crack problems using distributed dislocation ring dipoles
od: Korsunsky, A, i dr.
Izdano: (2000)

Size and scale effects in fretting fatigue thresholds
od: Dini, D, i dr.
Izdano: (2005)

The evolution of electrochemical, microstructural, and mechanical properties of aluminium alloy 2024-T4 (D16AT) during fatigue cycling
od: Salimon, S, i dr.
Izdano: (2010)

A study of residual elastic strain distribution in an AZ91 Mg alloy bar loaded in four point bending
od: Prakash, D, i dr.
Izdano: (2008)

Debonding of a weak interface in front of a through-thickness crack
od: Korsunsky, A
Izdano: (2001)

The influence of coating cracking and debonding on the hardness of coated systems
od: Tuck, J, i dr.
Izdano: (2000)

An extension of the Dang Van fatigue criterion to finite life predictions
od: Korsunsky, A, i dr.
Izdano: (2009)

Microstructural Impact on Fatigue Crack Growth Behavior of Alloy 718
od: Christian Gruber, i dr.
Izdano: (2022-04-01)

Variational determination of the crack trajectory in inhomogeneous media
od: Miklashevich, I, i dr.
Izdano: (2001)

The relationship between the Dang Van criterion and the traditional bulk fatigue criteria
od: Peridas, G, i dr.
Izdano: (2003)

Residual stresses in rolled and machined nickel alloy plates: synchrotron X-ray diffraction measurement and three-dimensional eigenstrain analysis
od: Korsunsky, A, i dr.
Izdano: (2007)

Analysis of cohesive zones in cracks and slip bands using hypersingular interpolative quadratures
od: Korsunsky, A, i dr.
Izdano: (2000)

Vector J-integral analysis of crack initiation at the edge of complete sliding contact
od: Ma, L, i dr.
Izdano: (2006)

Vector J-integral analysis of crack interaction with pre-existing singularities
od: Ma, L, i dr.
Izdano: (2006)

Fundamental eigenstrain solutions for axisymmetric crack problems
od: Korsunsky, A
Izdano: (1995)

Fatigue crack growth rate analysis in a titanium alloy
od: Korsunsky, A, i dr.
Izdano: (2008)

Effect of machined surface condition on fatigue strength of Ni based superalloy Alloy 718
od: Shota HASUNUMA, i dr.
Izdano: (2015-11-01)

Intergranular stresses in polycrystalline fatigue: diffraction measurement and self-consistent modelling
od: Korsunsky, A, i dr.
Izdano: (2003)

Variational eigenstrain analysis of synchrotron diffraction measurements of residual elastic strain in a bent titanium alloy bar
od: Korsunsky, A
Izdano: (2006)

Residual stress analysis in shot peened and fretting fatigued samples by the eigenstrain method
od: Korsunsky, A, i dr.
Izdano: (2006)

Neutron diffraction analysis of stresses in an in-plane biaxially-fatigued stainless steel sample of cruciform geometry
od: Taran, Y, i dr.
Izdano: (2008)

The correlation between plastic strain and anisotopy strain in aluminium alloy polycrystals
od: Korsunsky, A, i dr.
Izdano: (2002)

Analysis of residual stresses around 'dimpled' cold-expanded holes in aluminum alloy plates
od: Zhang, S, i dr.
Izdano: (2008)

On the micromechanics of micro-cantilever sensors: property analysis and eigenstrain modeling
od: Korsunsky, A, i dr.
Izdano: (2007)

On the measurement and interpretation of residual stress at the micro-scale
od: Korsunsky, A, i dr.
Izdano: (2010)

Analysis of plastic deformation and residual elastic strain in a titanium alloy using synchrotron x-ray diffraction
od: Golshan, M, i dr.
Izdano: (2005)

Some aspects of crack initiation in mild steel subjected to fatigue stressing in a corrosive environment
od: Ray, G. P.
Izdano: (1983)

The character of dislocation structure evolution in nanocrystalline FCC Ni-Co alloys prepared by high-energy mechanical milling
od: Salimon, A, i dr.
Izdano: (1999)

Synchrotron energy-dispersive X-ray diffraction analysis of residual strains around friction welds between dissimilar aluminium and nickel alloys
od: Jun, T, i dr.
Izdano: (2008)

Neutron diffraction investigation of an in-plane biaxial fatigued stainless steel sample of cruciform geometry
od: Taran, Y, i dr.
Izdano: (2008)

Prediction of fatigue crack growth rates in Ti-6Al-4V alloy
od: Korsunsky, A, i dr.
Izdano: (2008)

The thermal expansion coefficient of mechanically alloyed Al-Cu-Fe quasicrystalline powders
od: Korsunsky, A, i dr.
Izdano: (2001)

Quasicrystalline phase formation by heating a mechanically alloyed Al65Cu23Fe12 powder mixture
od: Tcherdyntsev, V, i dr.
Izdano: (2002)

Crystallochemical aspects of solid state reactions in mechanically alloyed Al-Cu-Fe quasicrystalline powders
od: Salimon, A, i dr.
Izdano: (2001)

The effect of wear on nucleation of cracks at the edge of an almost complete contact
od: Hills, D, i dr.
Izdano: (2010)

High energy transmission micro-beam Laue synchrotron X-ray diffraction
od: Hofmann, F, i dr.
Izdano: (2010)