Strain rate dependent constitutive modelling of 3D printed polymers

Strain rate dependent constitutive modelling of 3D printed polymers

Detalhes bibliográficos
Main Authors:	Lißner, M, Thomson, D, Petrinic, N, Bergmann, J
Formato:	Journal article
Idioma:	English
Publicado em:	EDP Sciences 2021

Registos relacionados

Strain Rate Dependent Constitutive Modelling of 3D Printed Polymers
Por: Lißner Maria, et al.
Publicado em: (2021-01-01)

Impact behaviour of 3D printed cellular structures for mouthguard applications
Por: Saunders, J, et al.
Publicado em: (2022)

A Puck-based localisation plane theory for rate- and pressure-dependent constitutive modelling of unidirectional fibre-reinforced polymers
Por: Thomson, D, et al.
Publicado em: (2017)

Identification of parameters for a rate and temperature-dependent constitutive model
Por: Elliott, B, et al.
Publicado em: (2003)

Strain rate and temperature dependent strain localization of dynamically stretched lightweight bars: from metal to polymer
Por: Zhang, L, et al.
Publicado em: (2021)

Strain-rate and off-axis loading effects on the fibre compression strength of CFRP laminates: experiments and constitutive modelling
Por: Thomson, D, et al.
Publicado em: (2020)

Strain rate and temperature dependent strain localization of dynamically stretched lightweight bars: from metal to polymer
Por: Zhang Longhui, et al.
Publicado em: (2021-01-01)

Experimental characterisation of the strain rate dependent failure and damage behaviour of 3D composites
Por: Gerlach, R, et al.
Publicado em: (2009)

Rate-dependent constitutive modeling of polymer subjected to dynamic loading
Por: Yuan, Jian Ming, et al.
Publicado em: (2013)

On the rate dependent behaviour of epoxy adhesive joints: Experimental characterisation and modelling of mode I failure
Por: Lissner, M, et al.
Publicado em: (2018)

STRAIN-RATE AND PRINTING DIRECTION DEPENDENCY OF COMPRESSIVE BEHAVIOUR OF 3D PRINTED STAINLESS STEEL 316L
Por: Michaela Neuhäuserová, et al.
Publicado em: (2019-12-01)

Thermomechanical constitutive response of a near α titanium alloy over a wide range of strain rates
Por: Zhang, L, et al.
Publicado em: (2021)

Thermomechanical constitutive response of a near α titanium alloy over a wide range of strain rates
Por: Zhang, L, et al.
Publicado em: (2021)

A rate dependent experimental and numerical analysis of adhesive joints under different loading directions
Por: Lißner, M, et al.
Publicado em: (2018)

On the rate-dependent plasticity modelling of unidirectional fibre-reinforced polymeric matrix composites
Por: Erice, B, et al.
Publicado em: (2018)

Measurement of pure shear constitutive relationship from torsion tests under quasi-static, medium, and high strain rate conditions
Por: Zhang, L, et al.
Publicado em: (2021)

Viscoelastic and high strain rate response of anisotropic graphene-polymer nanocomposites fabricated with stereolithographic 3D printing
Por: Lai, Chang Quan, et al.
Publicado em: (2021)

Unveiling the mechanism of the in situ> formation of 3d fiber macroassemblies with controlled properties
Por: Dong, S, et al.
Publicado em: (2023)

Strain rate dependence of a super-elastic NiTi alloy
Por: Siviour, C, et al.
Publicado em: (2009)

The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
Por: Gerlach, R, et al.
Publicado em: (2013)

TEXTURE DEPENDENCY OF HIGH STRAIN RATE PROPERTIES OF Ti-6Al-4V
Por: Wielewski, E, et al.
Publicado em: (2009)

Pressure and temperature dependent dynamic flow and failure behavior of PMMA at intermediate strain rates
Por: Zhang, L, et al.
Publicado em: (2021)

Characterisation and modelling of the rate-dependent behaviour of adhesive bonded interfaces
Por: Lissner, M
Publicado em: (2019)

Refinement of a 3D finite strain viscoelastic constitutive model for thermally induced shape memory polymers
Por: Yingyu Wang, et al.
Publicado em: (2021-04-01)

The dependency of compressive response of epoxy syntactic foam on the strain rate and temperature under rigid confinement
Por: Zhang, L, et al.
Publicado em: (2021)

Modeling of the Strain Rate Dependency of Polycarbonate’s Yield Stress: Evaluation of Four Constitutive Equations
Por: Abdullah A. Al-Juaid, et al.
Publicado em: (2016-01-01)

Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloys: Experiments and modelling
Por: Zhang, L, et al.
Publicado em: (2019)

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites
Por: Chen, Y, et al.
Publicado em: (2023)

Influence of strain history on dynamic strain localization and stress state during high-rate tensile loading of titanium alloys: experiments, modelling and analytical methods
Por: Gour, G, et al.
Publicado em: (2022)

Computational modeling of constitutive behaviour of 3D printed composite structures
Por: Madhukar Somireddy, et al.
Publicado em: (2021-03-01)

Manufacture dependent differential biodegradation of 3D printed shape memory polymers
Por: Ryan Akman, et al.
Publicado em: (2024-12-01)

Effect of high strain rates and temperature on the micromechanical properties of 3D-printed polymer structures made by two-photon lithography
Por: Nadia Rohbeck, et al.
Publicado em: (2020-10-01)

Strain rate dependent compressive properties of glass microballoon epoxy syntactic foams
Por: Li, P, et al.
Publicado em: (2009)

On the protectiveness of additively manufactured mouthguards
Por: Lißner, M, et al.
Publicado em: (2023)

A novel method for the mechanical testing of sports mouthguards
Por: Goldberg, T, et al.
Publicado em: (2022)

On the protectiveness of additively manufactured mouthguards
Por: M. Lißner, et al.
Publicado em: (2023-10-01)

3D printing of conducting polymers
Por: Yuk, Hyunwoo, et al.
Publicado em: (2021)

3D Printing and Biodegradable Polymers
Por: Saparová Simona, et al.
Publicado em: (2024-09-01)

3D printing of conducting polymers
Por: Hyunwoo Yuk, et al.
Publicado em: (2020-03-01)

A strain rate dependent thermo-elasto-plastic constitutive model for crystalline metallic materials
Por: Cen Chen, et al.
Publicado em: (2021-04-01)