An improved punch friction test in sheet metal forming

An improved punch friction test in sheet metal forming

Bibliographic Details
Main Authors:	Hassan, Mohamed Mohsen Abdel-Naeim, El-Sebaie, Mohamed Gad, Yamaguchi, K.
Format:	Article
Published:	2001
Subjects:	TS Manufactures

Similar Items

Friction aided deep drawing of sheet metals using polyurethane ring and auxiliary metal punch. Part 1: experimental observations on the deep drawing of aluminium thin sheets and foils
by: Hassan, M.A., et al.
Published: (2002)

Friction aided deep drawing of sheet metals using polyurethane ring and auxiliary metal punch. Part 2: analysis of the drawing mechanism and process parameters
by: Hassan, M.A., et al.
Published: (2002)

Design and simulation of die and punch for sheet metal on round bending
by: Teh, Soon Chiang
Published: (2007)

Friction aided deep drawing of aluminum sheet using blank holder divided into four segments
by: Hatanaka, N., et al.
Published: (2010)

Prevention of Wrinkling in Shrink Flanging of Ultra-High Strength Steel Sheets Using Gradually Contacting Punch
by: Zamzuri, Hamedon, et al.
Published: (2014)

The nonlinear elastic and viscoelastic passive properties of left ventricular papillary muscle of a guinea pig heart
by: Hassan, Mohamed Mohsen Abdel-Naeim, et al.
Published: (2012)

Experimental study on process parameter to reduce wrinkling in sheet metal forming
by: Nik Muhd Hazwan, Nik Abd Aziz
Published: (2013)

Decoupled third-order fuzzy sliding model control for cart-inverted pendulum system
by: Elsayed, B.A., et al.
Published: (2013)

Effect of curvature and thickness of aluminum shells on the energy absorption in low velocity impact
by: Hassan, Mohamed Mohsen Abdel-Naeim, et al.
Published: (2012)

Design, fabrication and performance test of die-punch set for powder compaction process
by: Logatarsan, Chandran
Published: (2017)

Springback prediction in sheet metal forming: constitutive equations, finite element simulations and experimental validation
by: Jasri, Mohamad
Published: (2013)

Effect of bulge shape on wrinkling formation and strength of stainless steel thin sheet
by: Hassan, Mohamed Mohsen Abdel-Naeim, et al.
Published: (2012)

Effect of slot geometry on the impact response of square column
by: Ghani, A.R.A., et al.
Published: (2012)

Numerical simulation of hot press forming process for quenchable sheet metal between nanocoolant and chilled water
by: S. K., Lim, et al.
Published: (2018)

Design and fabricate storage cabinet for turret punch tool
by: Muhammad Afiq, Ahmad Mustaza
Published: (2008)

Design suitable punch or die to overcome springback on u-bending
by: Tuan Abdul Hadi, Tuan Jusoh
Published: (2012)

Friction stir welding of dissimilar metal
by: Sahidi, Sujanuriah
Published: (2013)

Friction aided deep drawing using newly developed blank-holder divided into eight segments
by: Hassan, M.A., et al.
Published: (2003)

A novel technique of friction aided deep drawing using a blank-holder divided into four segments
by: Hassan, M.A., et al.
Published: (2003)

Combined method for die compensation in sheet metal forming
by: Muhammad Marhaban, Agus Dwi Anggono
Published: (2014)

Vision system for strain measurement in tensile test of boron sheet metal
by: Nik Nurulhusna, Muhmed Razali
Published: (2016)

Investigation of surface metal matrix composites of reinforced aluminium alloy produced using friction stir processing
by: Che Dini Marini, Che Mohammad Ishkandar El-Rahimin
Published: (2020)

Optimization of process parameters in sheet metal formng by using Taguchi method
by: Mohd Amiruzamin, Mohd Shaufi
Published: (2008)

A novel process on friction aided deep drawing using tapered blank holder divided into four segments
by: Hassan, M.A., et al.
Published: (2005)

Analysis on thin sheet metal feeding characteristic by a servo roll feeder
by: Mohamad Zulhisyam, Mohd Razmi
Published: (2013)

Development of a new process for producing deep square cups through conical dies
by: Hezam, L.M.A., et al.
Published: (2009)

Optimization of surface roughness and wall thickness in dieless incremental forming of aluminum sheet using taguchi
by: Zamzuri, Hamedon, et al.
Published: (2018)

Repetitive forging (RF) using inclined punches as a new bulk severe plastic deformation method
by: Babaei, A., et al.
Published: (2012)

Sintering properties of hydroxyapatite powders prepared using different methods
by: Ramesh, S., et al.
Published: (2012)

Experimental Study on Friction Coefficient and Wear Rate of Gun Metal Sliding Against Different Counterface Materials
by: Nuruzzaman, D. M., et al.
Published: (2014)

Effects of process parameters on selected properties of liquid compression-molded vinyl ester sheets
by: Abd. Rahman, Mohamed, et al.
Published: (2011)

Improvement of interlocking thin sheet metal in joining using plastic deformation process
by: Mohd Nor Fikry, Jamaludin
Published: (2016)

Experimental assessment of stamping parameters in a non-isothermal sheet metal forming technology
by: Nur Asyran Wanie, Baharom
Published: (2013)

The development of friction welding systems
by: H. K. Tham, Abdul Ghalib
Published: (1992)

Surface roughness and wear properties of Al–Al2O3 metal matrix composites fabricated using friction stir processing
by: Fatchurrohman, Nanang, et al.
Published: (2018)

The effect of spin and friction on reaction forces in a soccer ball impact: A computational study
by: Mohd Hasnun Ariff, Hassan, et al.
Published: (2018)

A fuzzy model for evaluation and prediction of slurry erosion of 5127 steels
by: Hassan, Mohamed Mohsen Abdel-Naeim, et al.
Published: (2012)

Investigation on the effect of Friction Stir Processing Parameters on Micro-structure and Micro-hardness of Rice Husk Ash reinforced Al6061 Metal Matrix Composites
by: Fatchurrohman, Nanang, et al.
Published: (2017)

Dieless incremental forming using 3-axis CNC milling machine for aluminium sheet
by: Shea, Cheng Kuang
Published: (2016)

Thickness Measurement of Liquid Sheet Spay Before Breakup
by: Nurrina, Rosli, et al.
Published: (2015)