Wear characteristics and adhesion behavior of calcium phosphate thin-films

Wear characteristics and adhesion behavior of calcium phosphate thin-films

Bibliographic Details
Main Authors:	Abd Shukor, Mohd Hamdi, Toque, J.A., Ide-Ektessabi, A.
Format:	Article
Published:	2010
Subjects:	TS Manufactures

Similar Items

In vitro study of electron beam deposited calcium phosphate coating in simulated body fluid
by: Abd Shukor, Mohd Hamdi, et al.
Published: (2007)

Dissolution behavior of simultaneous vapor deposited calcium phosphate coatings in vitro
by: Abd Shukor, Mohd Hamdi, et al.
Published: (2007)

Effect of the processing parameters on the integrity of calcium phosphate coatings produced by RF-magnetron sputtering
by: Toque, Jay Arre, et al.
Published: (2009)

Effect of the processing parameters on the integrity of calcium phosphate coatings produced by RF-magnetron sputtering
by: Toque, Jay Arre, et al.
Published: (2009)

Calcium phosphate coatings: a comparative study between simultaneous vapor deposition and electron beam deposition techniques
by: Abd Shukor, Mohd Hamdi, et al.
Published: (2006)

Adhesion failure behavior of sputtered calcium phosphate thin film coatings evaluated using microscratch testing
by: Toque, J.A., et al.
Published: (2010)

Adhesion failure behavior of sputtered calcium phosphate thin film coatings evaluated using microscratch testing
by: Toque, Jay Arre, et al.
Published: (2010)

The influence of sintering temperature on the properties of compacted bovine hydroxyapatite
by: Herliansyah, M.K., et al.
Published: (2009)

Optimum mechanical behavior of calcium phosphate cement/hydroxyl group functionalized multi-walled carbon nanotubes/bovine serum albumin composite using metaheuristic algorithms
by: Sadollah, A., et al.
Published: (2014)

Sintering and properties of dense manganese-doped calcium phosphate bioceramics prepared using sol-gel derived nanopowders
by: Sopyan, I., et al.
Published: (2011)

Effects of bismuth oxide on the properties of calcium phosphate bioceramics
by: W., H. Yeo, et al.
Published: (2011)

Low temperature hydrothermal synthesis of calcium phosphate ceramics: effect of excess Ca precursor on phase behavior
by: Alqap, Asep Sofwan F., et al.
Published: (2009)

Optimizing the PVD TiN thin film coating as parameters on aerospace AL7075-T6 alloy for higher coating hardness and adhesion with better tribological properties of the coating surface
by: Zalnezhad, E., et al.
Published: (2013)

The effects of calcium excess,water amount and mixing time on the injectability of calcium phosphate filling materials
by: Alqap, Asep Sofwan F., et al.
Published: (2012)

Effects of manganese doping on properties of sol gel derived biphasic calcium phosphate ceramics
by: Sopyan, I., et al.
Published: (2011)

Effect of grain size on vickers microhardness and fracture toughness in calcium phosphate bioceramics
by: Tolouei, R., et al.
Published: (2011)

Preparation of nano-structured manganese doped-biphasic calcium phosphate powders via sol-gel method
by: Iis, Sopyan, et al.
Published: (2009)

Sintering and properties of dense manganese-doped calcium phosphate bioceramics prepared using sol-gel derived nanopowders
by: Sopyan, Iis, et al.
Published: (2011)

Investigating the fretting fatigue life of thin film titanium nitride coated aerospace Al7075-T6 alloy
by: Zalnezhad, E., et al.
Published: (2012)

Prediction of TiN coating adhesion strength on aerospace AL7075-T6 alloy using fuzzy rule based system
by: Zalnezhad, E., et al.
Published: (2012)

Phase behaviour of manganese-doped biphasic calcium phosphate ceramics synthesized via sol-gel method
by: Nawawi, Natasha Ahmad, et al.
Published: (2011)

Surface hardness prediction of CrN thin film coating on AL7075-T6 alloy using fuzzy logic system
by: Zalnezhad, E., et al.
Published: (2013)

A fuzzy logic based model to predict surface hardness of thin film TiN coating on aerospace AL7075-T6 alloy
by: Zalnezhad, E., et al.
Published: (2013)

Quality characteristics of thin-walled plastic injection parts
by: Noh, Shahril
Published: (2010)

Correlation Between the Microstructure of Copper Oxide Thin Film and Its Gas Sensing Response
by: Ahmad Faizal, Mohd Zain, et al.
Published: (2014)

Preparation of tin oxide (SnO2) thin films using thermal oxidation
by: Nuraini, Abdullah, et al.
Published: (2018)

Recent progress and development of TiO2 thin film photocatalysts for pollutant removal
by: Abd Aziz, Radhiyah, et al.
Published: (2009)

Compound two-dimensional thermo-elastic and thermodynamic analysis for axis-oriented epitaxial lead titanate thin films
by: Hassan, M.A., et al.
Published: (2006)

Growth and structure of heteroepitaxial lead titanate thin films constrained by miscut strontium titanate substrates
by: Ichikawa, Y., et al.
Published: (2006)

Interrelationships between cutting force variation and tool wear in end-milling
by: Sarhan, A., et al.
Published: (2001)

Analysis on thin sheet metal feeding characteristic by a servo roll feeder
by: Mohamad Zulhisyam, Mohd Razmi
Published: (2013)

Adhesion and wear behavior of nanostructured titanium oxide thin films
by: Hasan, M.M., et al.
Published: (2010)

A Review on Nozzle Wear in Abrasive Water Jet Machining Application
by: Syazwani, H., et al.
Published: (2016)

The evaluation of EOR methods for a heavy-oil reservoir with the AHP method: The case of ferdowsi reservoir
by: Akhavan, A., et al.
Published: (2013)

Synthesis SiO2-TiO2 powder and thin film photocatalyst through sol-gel
by: Abd Aziz, Radhiyah, et al.
Published: (2009)

Friction Coefficient and Wear Rate of Copper and Aluminum Sliding against Mild Steel
by: Nuruzzaman, D. M., et al.
Published: (2012)

Experimental Investigation of Friction Coefficient and Wear Rate of Different Sliding Pairs
by: Chowdhury, M. A., et al.
Published: (2013)

Investigation of gap filling ability of Ag-Cu-In brazing filler metals
by: Sisamouth, L., et al.
Published: (2010)

Investigation into minimal-cutting-fluid application in high-speed milling of hardened steel using carbide mills
by: Thepsonthi, T., et al.
Published: (2009)

Mechanochemical synthesis of hydroxyapatite nanopowder: effects of rotation speed and milling time on powder properties
by: Adzila, S., et al.
Published: (2012)