Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO)
Fused Deposition Modelling (FDM) is an additive manufacturing-based rapid prototyping technology that has gained widespread attention due to its ability to produce complex geometries with relatively low cost and fast production time. However, the surface finish of the FDM printed parts can be advers...
| Main Authors: | , , , , , |
|---|---|
| Format: | Article |
| Published: |
Seventh Sense Research Group
2023
|
| _version_ | 1817927586038153216 |
|---|---|
| author | Hadi Irazman, Hani Nasuha Saad, Mohd Sazli Baharudin, Mohamad Ezral Zakaria, Mohd Zakimi Nor, Azuwir Mohd As'arry, Azizan |
| author_facet | Hadi Irazman, Hani Nasuha Saad, Mohd Sazli Baharudin, Mohamad Ezral Zakaria, Mohd Zakimi Nor, Azuwir Mohd As'arry, Azizan |
| author_sort | Hadi Irazman, Hani Nasuha |
| collection | UPM |
| description | Fused Deposition Modelling (FDM) is an additive manufacturing-based rapid prototyping technology that has gained widespread attention due to its ability to produce complex geometries with relatively low cost and fast production time. However, the surface finish of the FDM printed parts can be adversely affected by the selection of input parameters, such as layer height, infill density, print temperature, etc. This study aims to investigate the impact of these parameters on surface roughness and optimize the FDM process to improve surface finish. Two optimization approaches were employed in the study to address this problem, namely the Response Surface Methodology (RSM) and the particle swarm optimization (PSO) method. The impacts of four factors, layer height, printing speed, infill density, and print temperature, on the surface roughness of Polylactic Acid (PLA) printed parts were evaluated. A Face-centred Central Composite Design (FCCD) was used to reduce the number of experiments and to optimize the process. Both RSM and PSO methods were employed to find the best combination of process parameters for minimum surface roughness. The results of the experiment indicated that the optimal settings for minimum surface roughness were a layer height of 0.10 mm, printing speed of 30.36 m/s, infill density of 77.10 %, and print temperature of 195.12 °C, resulting in a surface roughness value of 1.31 µm. From these findings, the PSO optimization method was found to be more effective than the RSM method, showing a significant improvement in surface roughness with a reduction of 13.5 %. |
| first_indexed | 2024-12-09T02:20:47Z |
| format | Article |
| id | upm.eprints-108807 |
| institution | Universiti Putra Malaysia |
| last_indexed | 2024-12-09T02:20:47Z |
| publishDate | 2023 |
| publisher | Seventh Sense Research Group |
| record_format | dspace |
| spelling | upm.eprints-1088072024-09-26T08:33:38Z http://psasir.upm.edu.my/id/eprint/108807/ Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) Hadi Irazman, Hani Nasuha Saad, Mohd Sazli Baharudin, Mohamad Ezral Zakaria, Mohd Zakimi Nor, Azuwir Mohd As'arry, Azizan Fused Deposition Modelling (FDM) is an additive manufacturing-based rapid prototyping technology that has gained widespread attention due to its ability to produce complex geometries with relatively low cost and fast production time. However, the surface finish of the FDM printed parts can be adversely affected by the selection of input parameters, such as layer height, infill density, print temperature, etc. This study aims to investigate the impact of these parameters on surface roughness and optimize the FDM process to improve surface finish. Two optimization approaches were employed in the study to address this problem, namely the Response Surface Methodology (RSM) and the particle swarm optimization (PSO) method. The impacts of four factors, layer height, printing speed, infill density, and print temperature, on the surface roughness of Polylactic Acid (PLA) printed parts were evaluated. A Face-centred Central Composite Design (FCCD) was used to reduce the number of experiments and to optimize the process. Both RSM and PSO methods were employed to find the best combination of process parameters for minimum surface roughness. The results of the experiment indicated that the optimal settings for minimum surface roughness were a layer height of 0.10 mm, printing speed of 30.36 m/s, infill density of 77.10 %, and print temperature of 195.12 °C, resulting in a surface roughness value of 1.31 µm. From these findings, the PSO optimization method was found to be more effective than the RSM method, showing a significant improvement in surface roughness with a reduction of 13.5 %. Seventh Sense Research Group 2023 Article PeerReviewed Hadi Irazman, Hani Nasuha and Saad, Mohd Sazli and Baharudin, Mohamad Ezral and Zakaria, Mohd Zakimi and Nor, Azuwir Mohd and As'arry, Azizan (2023) Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO). International Journal of Engineering Trends and Technology, 71 (9). 92 - 103. ISSN 2349-0918; ESSN: 2231-5381 https://ijettjournal.org/archive/ijett-v71i9p209 10.14445/22315381/ijett-v71i9p209 |
| spellingShingle | Hadi Irazman, Hani Nasuha Saad, Mohd Sazli Baharudin, Mohamad Ezral Zakaria, Mohd Zakimi Nor, Azuwir Mohd As'arry, Azizan Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title | Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title_full | Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title_fullStr | Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title_full_unstemmed | Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title_short | Optimizing surface roughness of PLA printed parts using Particle Swarm Optimization (PSO) |
| title_sort | optimizing surface roughness of pla printed parts using particle swarm optimization pso |
| work_keys_str_mv | AT hadiirazmanhaninasuha optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso AT saadmohdsazli optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso AT baharudinmohamadezral optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso AT zakariamohdzakimi optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso AT norazuwirmohd optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso AT asarryazizan optimizingsurfaceroughnessofplaprintedpartsusingparticleswarmoptimizationpso |