Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites
The aim of this simulation work is to carry out a comparative study of the fibre orientation distribution (FOD) in the short glass fibre reinforced injection moulded thermoplastic (SgFRIMT) composites. The objective of this research is to use a numerical method to investigate the effect of two s...
| Main Author: | |
|---|---|
| Format: | Thesis |
| Language: | English English |
| Published: |
2002
|
| Online Access: | http://psasir.upm.edu.my/id/eprint/12084/1/FK_2002_50.pdf |
| _version_ | 1811137338281033728 |
|---|---|
| author | Zainudin, Edy Syams |
| author_facet | Zainudin, Edy Syams |
| author_sort | Zainudin, Edy Syams |
| collection | UPM |
| description | The aim of this simulation work is to carry out a comparative study of
the fibre orientation distribution (FOD) in the short glass fibre reinforced
injection moulded thermoplastic (SgFRIMT) composites. The objective of this
research is to use a numerical method to investigate the effect of two
significant parameters namely, speed of injection and thickness of specimen,
on the FOD of the SgFRIMT composites. The numerical simulation is
conducted by Moldflow Plastics Insight (MPI) software. MPI software is used
to investigate the flow behaviour and to examine the effects of processing
conditions on the mouldings. Effects of the thickness of the specimen and
injection speed are considered since they have great influence on the
mechanical properties of the products.
The effect of the injection speed on the FOD is not significant in the
thicker plaque. The difference of FOD between the 2 mm and 4 mm plaques
has been reported and it was observed that thinner plaque received more
aligned fibres at the flow direction due to higher shearing flow generated
compared to the thicker one.The fibre orientation is observed for variations from the skin to the
core. I n the skin the fibres are highly aligned in the flow direction, whereas in
the core the fibres are mainly aligned in the direction transverse to the flow.
The more the short fibres are aligned in the moulded parts the better the
mechanical behaviour is. Higher injection speeds influence the fibres so as to
align along the flow direction but decreases from the skin to the middle/core
plane.
The overall result of executing the MPI program over the published
results gives a full agreement upon the FOD in SgFRIMT composites. The
simulated results also agree with other published numerical works. These
verify the use of MPI simulation method. |
| first_indexed | 2024-03-06T07:24:28Z |
| format | Thesis |
| id | upm.eprints-12084 |
| institution | Universiti Putra Malaysia |
| language | English English |
| last_indexed | 2024-09-25T03:32:42Z |
| publishDate | 2002 |
| record_format | dspace |
| spelling | upm.eprints-120842024-06-28T01:49:47Z http://psasir.upm.edu.my/id/eprint/12084/ Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites Zainudin, Edy Syams The aim of this simulation work is to carry out a comparative study of the fibre orientation distribution (FOD) in the short glass fibre reinforced injection moulded thermoplastic (SgFRIMT) composites. The objective of this research is to use a numerical method to investigate the effect of two significant parameters namely, speed of injection and thickness of specimen, on the FOD of the SgFRIMT composites. The numerical simulation is conducted by Moldflow Plastics Insight (MPI) software. MPI software is used to investigate the flow behaviour and to examine the effects of processing conditions on the mouldings. Effects of the thickness of the specimen and injection speed are considered since they have great influence on the mechanical properties of the products. The effect of the injection speed on the FOD is not significant in the thicker plaque. The difference of FOD between the 2 mm and 4 mm plaques has been reported and it was observed that thinner plaque received more aligned fibres at the flow direction due to higher shearing flow generated compared to the thicker one.The fibre orientation is observed for variations from the skin to the core. I n the skin the fibres are highly aligned in the flow direction, whereas in the core the fibres are mainly aligned in the direction transverse to the flow. The more the short fibres are aligned in the moulded parts the better the mechanical behaviour is. Higher injection speeds influence the fibres so as to align along the flow direction but decreases from the skin to the middle/core plane. The overall result of executing the MPI program over the published results gives a full agreement upon the FOD in SgFRIMT composites. The simulated results also agree with other published numerical works. These verify the use of MPI simulation method. 2002-07 Thesis NonPeerReviewed text en http://psasir.upm.edu.my/id/eprint/12084/1/FK_2002_50.pdf Zainudin, Edy Syams (2002) Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites. Masters thesis, Universiti Putra Malaysia. English |
| spellingShingle | Zainudin, Edy Syams Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title | Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title_full | Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title_fullStr | Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title_full_unstemmed | Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title_short | Numerical Investigation Of Fibre Orientation In Short Glass Fibre Reinforced Injection-Moulded Thermoplastic Composites |
| title_sort | numerical investigation of fibre orientation in short glass fibre reinforced injection moulded thermoplastic composites |
| url | http://psasir.upm.edu.my/id/eprint/12084/1/FK_2002_50.pdf |
| work_keys_str_mv | AT zainudinedysyams numericalinvestigationoffibreorientationinshortglassfibrereinforcedinjectionmouldedthermoplasticcomposites |