Analysis of Automated G-Clip machine processes and substation process with simulation by using CAD software.

Analysis of Automated G-Clip machine processes and substation process with simulation by using CAD software.

Veure altres versions (1)

The paper presents the work of analysis of Automated G-clip Paperclip machine of using Solidworks Simulation and a comparison between results of each analysis in cutting process using design of experiment (DOE) and followed by design verification of simulating the cutting process after design change...

Descripció completa

Dades bibliogràfiques
Autors principals:	Kamaluddin, Rohaya, Mohd Ariffin, Mohd Khairol Anuar, Tang, Sai Hong, Mohammed, S. B.
Format:	Conference or Workshop Item
Idioma:	English English
Accés en línia:	http://psasir.upm.edu.my/id/eprint/26627/1/ID%2026627.pdf

Ítems similars

Analysis of automated G-clip machine processes and substation process with simulation by using CAD software
per: Mohd Ariffin, Mohd Khairol Anuar, et al.
Publicat: (2014)

Effect of boric acid mixture as solid lubricant towards machining processes
per: Sulaiman, Shamsuddin, et al.
Publicat: (2013)

A hybrid genetic-heuristic algorithm for scheduling of automated guided vehicles and quay cranes in automated container terminals
per: Homayouni, Seyed Mahdi, et al.
Publicat: (2009)

Using simulated annealing algorithm for optimization of quay cranes and automated guided vehicles scheduling
per: Homayouni, Seyed Mahdi, et al.
Publicat: (2011)

Conflict-free automated guided vehicles routing using multi-objective genetic algorithm
per: Umar, Ali Umar, et al.
Publicat: (2013)

Performance optimization of simultaneous machine and automated guided vehicle scheduling using fuzzy logic controller based genetic algorithm.
per: Sulaiman, Shamsuddin, et al.
Publicat: (2012)

Effect of machining process on surface microhardness of titanium carbide reinforced aluminium LM6 composite
per: Yusuf, Muhammad, et al.
Publicat: (2014)

The specificities of the thinking process in adolescents. Clip thinking
per: Diana Koshkodan, et al.
Publicat: (2022-11-01)

Biogeography based optimization (BBO) algorithm to minimise non-productive time during hole-making process
per: Tamjidy, Mehran, et al.
Publicat: (2015)

Security Management and Traceability of Substation Software Versions
per: Jin LI, et al.
Publicat: (2021-11-01)

Fujitsu software : process control and automated customization
per: Cusumano, Michael A.
Publicat: (2009)

Fujitsu software : process control to automated customization
per: Cusumano, Michael A.
Publicat: (2009)

Computer simulation and experimental investigation of solidification casting process
per: Sulaiman, Suraya, et al.
Publicat: (2011)

Software-Defined Analog Processing Based on IEC 61850 Implemented in an Edge Hardware Platform to be Used in Digital Substations
per: Maria Teresa Villen Martinez, et al.
Publicat: (2024-01-01)

Fundamental of machine processing for automation /
per: 240970 Kuniaki Unno
Publicat: ([19-)

Automated process planning system considering machining feature recognition suitable for end-milling using CAD models in STL format
per: Takayuki HIRAYAMA, et al.
Publicat: (2024-11-01)

The impact of cad on the design process /
per: 257114 Prida A/P Endin On Tong
Publicat: (2008)

"To clip or not to clip. That is no question!"
per: Aznar, M, et al.
Publicat: (2017)

A hybrid method using analytic hierarchical process and artificial neural network for supplier selection
per: Tang, Sai Hong, et al.
Publicat: (2013)

CAD/CAM modeling : rolling process simulation /
per: Mohd. Abd. Razak Sumairi, 1986-, et al.
Publicat: (2010)

Influence of cutting parameters on surface roughness for wet and dry turning process.
per: Mohd Ariffin, Mohd Khairol Anuar, et al.
Publicat: (2011)

IC CAD & design automation
per: Jong, Ching Chuen
Publicat: (2008)

Cutting processes of natural fiber reinforced polymer composites
per: Masoud, Fathi, et al.
Publicat: (2020)

Comparisons process-to-bay level peer-to-peer network delay in IEC 61850 substation communication systems
per: Ali, Nasser Hasan, et al.
Publicat: (2014)

Diagnostic Accuracy of Automated Diabetic Retinopathy Image Assessment Software: IDx-DR and RetCAD
per: Andrzej Grzybowski, et al.
Publicat: (2024-11-01)

An optimise drilling process for an aircraft composite structure using design of experiments
per: Mohd Ariffin, Mohd Khairol Anuar, et al.
Publicat: (2009)

Optimization of cutting parameters on turning process based on surface roughness using response surface methodology
per: Yusuf, Muhammad, et al.
Publicat: (2012)

Design an intake substation /
per: 267361 Hasnizal Mohd. Saharudin
Publicat: (1994)

Improving equipment effectiveness by designing optimal production process
per: Okhovat, Mohammad Amin, et al.
Publicat: (2012)

WLAN oriented optimization of process bus in IEC 61850-based substation communication network
per: Ali, Nasser Hasan, et al.
Publicat: (2015)

Process parameters for cylindrical deep drawing components
per: Sulaiman, Shamsuddin, et al.
Publicat: (2015)

The application of computer software to analyze the process flow and factory automation /
per: 394149 Abd. Halim Ahmad
Publicat: (1996)

Modeling and simulation of forward Al extrusion process using FEM
per: Magid, Hani Mizhir, et al.
Publicat: (2014)

A committee machine approach to multiple response optimization
per: Golestaneh, Seyed Jafar, et al.
Publicat: (2011)

An Effective Security Scheme for Attacks on Sample Value Messages in IEC 61850 Automated Substations
per: S. M. Suhail Hussain, et al.
Publicat: (2023-01-01)

Software Structuring Principles for VLSI CAD
per: Katzenelson, Jacob, et al.
Publicat: (2004)

CAD software for semiconductor device modeling /
per: 384290 Yasmin Othman
Publicat: (2004)

CAD software for semiconductor device modeling
per: Othman, Yasmin
Publicat: (2004)

An overview on robust design hybrid metamodeling: Advanced methodology in process optimization under uncertainty
per: Parnianifard, Amir, et al.
Publicat: (2017)

Risk Assessment of Substation Automation System Failure Considering Human Reliability
per: Yu HUANG, et al.
Publicat: (2019-10-01)