Effect of chip load and spindle speed on cutting force of Hastelloy X
Research on cutting force revealed that the cutting force decreases as cutting speed increases, which is in line with Salomon’s Theory. However, the fundamental behaviour was never clearly explained because most studies had focused on increasing the cutting speed by increasing spindle speed without...
| Main Authors: | , , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Universiti Malaysia Pahang
2020
|
| Online Access: | http://psasir.upm.edu.my/id/eprint/88575/1/ABSTRACT.pdf |
| _version_ | 1825936537831866368 |
|---|---|
| author | Mohd Nor, Nor Aznan Baharudin, B. T. Hang Tuah Ghani, Jaharah Leman, Zulkiflle Mohd Ariffin, Mohd Khairol Anuar |
| author_facet | Mohd Nor, Nor Aznan Baharudin, B. T. Hang Tuah Ghani, Jaharah Leman, Zulkiflle Mohd Ariffin, Mohd Khairol Anuar |
| author_sort | Mohd Nor, Nor Aznan |
| collection | UPM |
| description | Research on cutting force revealed that the cutting force decreases as cutting speed increases, which is in line with Salomon’s Theory. However, the fundamental behaviour was never clearly explained because most studies had focused on increasing the cutting speed by increasing spindle speed without retaining the rate of chip load. On that note, the effect of increasing spindle speed while chip load is constant on the cutting force of Hastelloy X is presented in this paper. Third Wave AdvantEdge software was applied and half-immersion up-milling simulations were conducted in dry condition. Result showed that the resultant force was primarily affected by the axial force, followed by normal force and feed force. Trend-lines indicated that the behaviour of cutting force components and resultant force was quadratic. Desirability Function Analysis (DFA) results revealed that the optimum combination of chip load and spindle speed led to lowest cutting force components and resultant force was at 0.013 mm/tooth and 24,100 RPM. Furthermore, the optimum cutting conditions that led to the lowest cutting force components and resultant force at chip loads of 0.016 mm/tooth and 0.019 mm/tooth was 24,100 RPM also. Therefore, increasing Material Removal Rate (MRR) while minimizing cutting force components and resultant force can be achieved by increasing the amount of chip load at spindle speed of 24,100 RPM. |
| first_indexed | 2024-03-06T10:45:48Z |
| format | Article |
| id | upm.eprints-88575 |
| institution | Universiti Putra Malaysia |
| language | English |
| last_indexed | 2024-03-06T10:45:48Z |
| publishDate | 2020 |
| publisher | Universiti Malaysia Pahang |
| record_format | dspace |
| spelling | upm.eprints-885752021-12-22T01:16:42Z http://psasir.upm.edu.my/id/eprint/88575/ Effect of chip load and spindle speed on cutting force of Hastelloy X Mohd Nor, Nor Aznan Baharudin, B. T. Hang Tuah Ghani, Jaharah Leman, Zulkiflle Mohd Ariffin, Mohd Khairol Anuar Research on cutting force revealed that the cutting force decreases as cutting speed increases, which is in line with Salomon’s Theory. However, the fundamental behaviour was never clearly explained because most studies had focused on increasing the cutting speed by increasing spindle speed without retaining the rate of chip load. On that note, the effect of increasing spindle speed while chip load is constant on the cutting force of Hastelloy X is presented in this paper. Third Wave AdvantEdge software was applied and half-immersion up-milling simulations were conducted in dry condition. Result showed that the resultant force was primarily affected by the axial force, followed by normal force and feed force. Trend-lines indicated that the behaviour of cutting force components and resultant force was quadratic. Desirability Function Analysis (DFA) results revealed that the optimum combination of chip load and spindle speed led to lowest cutting force components and resultant force was at 0.013 mm/tooth and 24,100 RPM. Furthermore, the optimum cutting conditions that led to the lowest cutting force components and resultant force at chip loads of 0.016 mm/tooth and 0.019 mm/tooth was 24,100 RPM also. Therefore, increasing Material Removal Rate (MRR) while minimizing cutting force components and resultant force can be achieved by increasing the amount of chip load at spindle speed of 24,100 RPM. Universiti Malaysia Pahang 2020 Article PeerReviewed text en http://psasir.upm.edu.my/id/eprint/88575/1/ABSTRACT.pdf Mohd Nor, Nor Aznan and Baharudin, B. T. Hang Tuah and Ghani, Jaharah and Leman, Zulkiflle and Mohd Ariffin, Mohd Khairol Anuar (2020) Effect of chip load and spindle speed on cutting force of Hastelloy X. Journal of Mechanical Engineering and Sciences, 14 (1). 6497 - 6503. ISSN 2289-4659; ESSN: 2231-8380 https://journal.ump.edu.my/jmes/article/view/1703 10.15282/jmes.14.1.2020.24.0509 |
| spellingShingle | Mohd Nor, Nor Aznan Baharudin, B. T. Hang Tuah Ghani, Jaharah Leman, Zulkiflle Mohd Ariffin, Mohd Khairol Anuar Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title | Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title_full | Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title_fullStr | Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title_full_unstemmed | Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title_short | Effect of chip load and spindle speed on cutting force of Hastelloy X |
| title_sort | effect of chip load and spindle speed on cutting force of hastelloy x |
| url | http://psasir.upm.edu.my/id/eprint/88575/1/ABSTRACT.pdf |
| work_keys_str_mv | AT mohdnornoraznan effectofchiploadandspindlespeedoncuttingforceofhastelloyx AT baharudinbthangtuah effectofchiploadandspindlespeedoncuttingforceofhastelloyx AT ghanijaharah effectofchiploadandspindlespeedoncuttingforceofhastelloyx AT lemanzulkiflle effectofchiploadandspindlespeedoncuttingforceofhastelloyx AT mohdariffinmohdkhairolanuar effectofchiploadandspindlespeedoncuttingforceofhastelloyx |