Wheelchair lifter

Wheelchair lifter

Basically, a wheelchair stair lift is a motorized, meaning by carrying a person seated in a wheelchair up and down stairs. A wheelchair lift, also known as a platform lift, or vertical platform lift is a fully powered device designed to raise a wheelchair and its occupant in order to overcome a step...

Full description

Bibliographic Details
Main Authors:	Sumri, Muhamad Zamir, Anuar, Nurul Azwani, Hassan, Mohd Fahrul, Suhaini, Rozita, Ismail, Salmi, Syed Adnan, Syed Fadhil
Format:	Book Section
Language:	English
Published:	Penerbit UTHM 2017
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://eprints.uthm.edu.my/4703/1/Chapter%208_EDP_S1.pdf

Similar Items

Applied anthropometric for wheelchair user in Malaysia
by: Adnan, Nursyahirah, et al.
Published: (2019)

A Study on Smart Wheelchair Systems
by: Alsibai, Mohammad Hayyan, et al.
Published: (2015)

Add-on-e-wheelchair conversion kit with lOT patient monitoring system
by: Mohamad Heerwan, Peeie, et al.
Published: (2018)

Innovation on Manual Wheelchair for Hemiplegic and Tetraplegic Patients
by: M. H., Muhammad Sidik, et al.
Published: (2020)

Parameters estimation and calibration of bldc motor for electric powered wheelchair
by: S. M., Asyraf, et al.
Published: (2018)

Investigation on electric motor braking control system for electric powered wheelchair
by: Muhammad Asyraf, Shahrom
Published: (2020)

Validation test on thresholds for wheelchair power-assist system activation using population data
by: M. H., Muhammad Sidik, et al.
Published: (2020)

Development of a new robust hybrid automata algorithm based on surface electromyography (SEMG) signal for instrumented wheelchair control
by: Mohd Hanafi, Muhammad Sidik
Published: (2020)

TRIZ and AHP in early design stage of a Novel Reconfigurable Wheelchair / Sumit Desai...[et al.]
by: Desai*,, Sumit, et al.
Published: (2019)

A Review on Electric Wheelchair Innovation to Ease Mobility and As a Rehabilitation Tool for Spinal Cord Impairment Patient
by: M. H., Muhammad Sidik, et al.
Published: (2020)

Motion control using voice for wheelchair application
by: Ismail, Hashimah
Published: (2006)

The comparison respond of braking torque control between PID and SMC controller for electric powered wheelchair descending on slope condition
by: Mohamad Heerwan, Peeie, et al.
Published: (2018)

The investigation on dynamic behavior of electric powered wheelchair during the obstacle avoidance
by: I. M., Sollehudin, et al.
Published: (2019)

Dried chili seeds separator machine
by: Husin, Mohd Asri, et al.
Published: (2017)

Characterization of a wave soldering process using Taguchi method
by: Mohd. Rohani, Jafri, et al.
Published: (1999)

Two-wheeled wheelchair stabilization using interval type-2 fuzzy logic controller
by: N. F., Jamin, et al.
Published: (2018)

Extruder for food product (otak–otak) with heater and roll cutter
by: Dol Baharin, Muhammad Zulhusmi, et al.
Published: (2017)

Speed estimation of the electric-powered wheelchair by proposing the state observer method based on experimental data
by: I. M., Sollehudin, et al.
Published: (2020)

Plugging brake system as a hill descend control for electric powered wheelchair: Experimental analysis
by: S. M., Asyraf, et al.
Published: (2019)

Fish ball maker machine
by: Zulkarnain, Muhammad Harith Ifwat, et al.
Published: (2017)

Motorized cart
by: Mohd Rani, Mohd Hafis, et al.
Published: (2017)

Performance of hollow reinforced concrete beam in structural member / Hamidun Mohd Noh...[et al.]
by: Mohd Noh, Hamidun, et al.
Published: (2020)

Hydraulic bearing puller
by: Abu Bakar, Nor Hidayah, et al.
Published: (2017)

Experimental observation of Jute/Epoxy composite plate subjected to impact loading
by: Omar, Nurihan, et al.
Published: (2011)

Development of solar powered mobile robot
by: Syed Musa Kazim, Syed Zainal Abidin
Published: (2013)

Pressure fryer
by: Johar, Ahmad Sufiyan, et al.
Published: (2017)

Material selection in mechanical design of car bumper
by: Nurul Azwan, Adnan
Published: (2009)

Leak detection in gas pipeline based on time-frequency analysis
by: Nurul Fatiehah, Adnan
Published: (2016)

An improved scheme for online recognition of control chart patterns
by: Hassan, Adnan
Published: (2011)

Cutting force of end cutting tool milling machining
by: Sharifah Noor Shahirah, Syed Mohd Nordin
Published: (2007)

Multipurpose automatic Kerisik packaging machine
by: Sukarman, Muhammad Izwan, et al.
Published: (2017)

Numerical Investigation of Ground Cooling Potential for Malaysian Climate
by: Mohd Yusof, Taib, et al.
Published: (2013)

Study of Effect of Thermal Diffusivity on Ground Temperature for Malaysian Climate
by: Mohd Yusof, Taib, et al.
Published: (2014)

Fe-Al Diffusion Bonding: Effect of reaction time on the interlayer thickness / Asmawi Ismail...[et al.]
by: Ismail, Asmawi, et al.
Published: (2018)

Markov Chain Modelling of Reliability Analysis and Prediction under Mixed Mode Loading
by: Salvinder, Singh, et al.
Published: (2015)

Variable speed drives as energy efficient strategy in pulp and paper industry
by: Syed Mustaffah, Sharifah Azma
Published: (2006)

3 in 1 processor coconut dehusker machine
by: Ngadiron, Mohamad Faridzuan, et al.
Published: (2017)

Electrical discharge machining of polycrystalline diamond using copper electrode – finishing condition
by: Ahmad, M.A. Haikal, et al.
Published: (2017)

Leak Detection in Pipeline Using Wavelet and Ceptrum Analysis
by: Makeen, Mohd Amin, et al.
Published: (2014)

CFD Calculation Of Impinging Confined Gas Jet Flamesfires
by: Anuar, Syed Muhammad Syimir Syed Mohamed
Published: (2017)