Development of cubic boron nitride coating on cutting tool steel

Development of cubic boron nitride coating on cutting tool steel

Bibliographic Details
Main Author:	Ramdan, Raden Dadan
Format:	Thesis
Published:	2004
Subjects:	TJ Mechanical engineering and machinery

Similar Items

Development of cubic boron nitride coating on cutting tool steel /
by: 289743 Raden Dadan Ramdan
Published: (2004)

Cubic boron nitride coated on steel substrate /
by: Esah Hamzah, et al.
Published: (2001)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
by: K. Seveen, K. Muniswaran
Published: (2007)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
by: Tang, Yu Cai
Published: (2006)

Investigation on surface roughness of mild steel using coated carbide cutting tools
by: Mohamad Rais, Ramli
Published: (2009)

Performance of coated carbide cutting tool while machining aluminium alloy and mild steel
by: Ismail, Ab.llah
Published: (2010)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
by: Wan Abdul Rahaman, Wan Emri
Published: (2006)

Effects of cutting tool coating on surface roughness in machining pre-hardened steel (p20)
by: Aini Rushda, Md Desa
Published: (2012)

Developing a Cutting Tool with Mild Steel for Printed Circuit Board
by: M. M., Noor, et al.
Published: (2008)

Tool wear and tool life performance of TiA1N coated carbide cutting tools when turning XW 42 hardened tool steel
by: Effendy, Effendy
Published: (2007)

Influence of cutting condition on chip morphology when turning hardened stainless steel using coated carbide cutting tools under minimum quantity of lubrication
by: Saad Elmunafi, Mohamed Handawi, et al.
Published: (2020)

Evaluation of ceramic cutting tool performance when turning tool steels
by: Konneh, Mohamed
Published: (1998)

Effect of Cutting Parameters on Sustainable Machining Performance of Coated Carbide Tool in Dry Turning Process of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Experimental investigation of multilayer coating performance on CBN cutting tools when turning of hardened AISI D2 cold work tool steel
by: Mohd. Yusof, Noordin, et al.
Published: (2006)

Effect of cutting speed and feed in turning hardened stainless steel using coated carbide cutting tool under minimum quantity lubrication using castor oil
by: Elmunafi, Mohamed Handawi Saad, et al.
Published: (2015)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
by: Mohd. Yusof, Noordin
Published: (2004)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
by: Mohd. Yusof, Noordin
Published: (2003)

Wear Mechanism of Coated and Uncoated Carbide Cutting Tool in Machining Process
by: J. A., Ghani, et al.
Published: (2016)

Microstructure analysis of aluminium metal matrix alloy with silicon carbide and hexogonal boron nitride
by: Talib, Norfazillah, et al.
Published: (2020)

Thermofluid behaviour of boron nitride nanotube nanofluid in a microchannel under optimized conditions
by: Mat, Mohamad Nur Hidayat, et al.
Published: (2023)

Investigation of the mechanical properties of electrodeposited nickel and magnetron sputtered chromium nitride coatings deposited on mild steel substrate
by: Bhatti, J., et al.
Published: (2016)

Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools.
by: Noordin, M. Y., et al.
Published: (2007)

Investigation of machining performance of the coated carbide cutting tools with murakami surface pretreatment
by: Khairul Azmi, Mohd Mawardzi
Published: (2012)

The effect of target and substrate separation on the properties of cubic boron nitride film coated on steel /
by: 179197 Esah Hamzah, et al.
Published: (2002)

Optimization of a boron nitride nanotubes nanofluid-cooled microchannel heat sink at different concentrations
by: Yusof, Nur Liyana Nabihah, et al.
Published: (2023)

Strain-Rate Sensitivity of Boron Alloyed Steel
by: Salwani, Mohd Salleh, et al.
Published: (2015)

Performance evaluation of ceramic and PCBN cutting tools when turning hardened steel
by: Abd. Jamil, Saiful Bahri
Published: (2004)

Performance of uncoated cutting tools when machining mild steel and aluminium alloy
by: Mohd Fahmi, Md Yusuf
Published: (2010)

Effect of tool edge geometry on cutting force and surface roughness when hard turning tool steel
by: Mohd. Yusof, Noordin, et al.
Published: (2012)

Investigation of machining performance of the coated carbide cutting tools with acid etching surface pretreatment
by: Muhammad Fahmi , Jasri
Published: (2012)

Performance evaluation of wiper coated ceramic tool when hard turning tool steel
by: Saad Elmunafi, Mohamed Handawi
Published: (2010)

Effect of Cold Rolling Treatment on the Formation of Titanium Oxide Layer on Ti6Al4V Alloys by Thermal-electrochemical Anodizing Processes
by: Ramdan, Raden Dadan, et al.
Published: (2013)

Influence of varying depth of cut and feed rate to tool wear rate and surface roughness in aluminium, mild steel and P20 tool steel
by: Nadirah, Ismail
Published: (2012)

Flexural Performance of the Heat-Treated Boron Alloyed Steel
by: Salwani, Mohd Salleh, et al.
Published: (2017)

Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel
by: Patil, Nagraj, et al.
Published: (2018)

Hard Turning of Stainless Steel using Wiper Coated Carbide Tool
by: Noordin, M.Y., et al.
Published: (2007)

Investigation of machining performance of coated alumina cutting tool insert with sand blasting surface pretreatment
by: Mohd Azrulnizam, Abd. Aziz
Published: (2012)

The impact of cutting tool materials on cutting force
by: Kamely, M. A., et al.
Published: (2011)

Comparison of the cutting force, power, tool life and torque in the end milling of modified AISI P20 tool steel
by: P. Vinothi, S Parawa Karan
Published: (2009)

Prediction of cutting force in end-milling operation of modified AISI P20 tool steel
by: Muhamad Nazumi, Basuki
Published: (2009)