Preparation and characterization of lignin based banana stem grafted acrylic acid

Preparation and characterization of lignin based banana stem grafted acrylic acid

Bibliographic Details
Main Author:	Nur Amalina Azhar
Format:	Thesis
Published:	2013
Subjects:	TS Manufactures

Similar Items

Preparation and characterization of lignin based banana stem grafted acrylic acid /
by: Nur Amalina Azhar, 1988-, et al.
Published: (2013)

Preparation and characterization of lignin based banana stem grafted acrylic acid [electronic resource) /
by: Nur Amalina Azhar, 1988-, et al.
Published: (2013)

Fabrication and characterization of medium density fiber board prepared from enzyme treated fiber and lignin based bio adhesive
by: Mohammed, Nasir
Published: (2013)

Enzymatic depolymerazation of lignin by laccases
by: Nor Hanimah, Hamidi
Published: (2013)

Lignin and cellulose wood for Polymeric Electrolyte
by: Fauziah Abdul Aziz
Published: (2009)

Lignin Production from Oil Palm Biomass
by: Zamardina, Zainal
Published: (2013)

Effect of banana skin on biodegradable NR latex
by: Yusriha , Mohd Yusoff
Published: (2012)

Microstructural and process characterization on the electrical conductivity and electrical discharge machinability of Al2O3-based ceramic composites
by: Mebrahitom, A., et al.
Published: (2018)

Film behaviour of natural rubber latex treated with banana skin
by: Goh, Tok Mun
Published: (2012)

Modification of lignin content in wood fiber by microwave heating and laccase treatment
by: Muhammad 'Izzat, Saidon
Published: (2010)

Synthesis, characterization, and morphology study of coco peat-grafted-poly(acrylic acid)/NPK slow release fertilizer hydrogel
by: Ros Azlinawati, Ramli, et al.
Published: (2019)

Investigation on the effect of sintering temperature and composition of titanium (Ti) on electrical conductivity of al2o3/zro2/ti ceramic composites
by: Nur Amalina, Sabuan
Published: (2021)

Characterization of tin oxide (SnO2) nanostructures prepared by thermal oxidation
by: Nuraini, Abdullah, et al.
Published: (2018)

Preparation and characterization of al-al2o3 graded composite materials under different sintering conditions
by: Farah Fazira, Kamaruzaman
Published: (2020)

Utilization of lignin in empty fruit bunch for production of fine chemicals: development of subcritical water technology and ΔpcaHG-ΔcatA Rhodococcus jostii RHA1
by: Ismail, Farah Syafiqah, et al.
Published: (2015)

The development of Zirconia and Copper toughened Alumina ceramic insert
by: Nur Amalina, Sabuan, et al.
Published: (2018)

A study on preparation and characterization of lignin based banana stem with acrylic acid and its effect on water absortion test / Siti Nur Amira Mazlan
by: Mazlan, Siti Nur Amira
Published: (2020)

Biodelinification as Pretreatment to Acid Hydrolysis of Oil Palm Trunk (OPT) : Kinetic Study
by: Wan Nur Atiqah, Wan Yusoff
Published: (2013)

Physicochemical and antibacterial properties of cotton fabric treated with chitosan-tripolyphosphate nanoparticles and lauric acid
by: Mamat, Siti Nur Hana
Published: (2016)

Preparation of thermoplastic container via thermoforming process
by: Nik Ruqiyah, Nik Hassan
Published: (2015)

Pso-based PID speed control of traveling wave ultrasonic motor under temperature disturbance
by: Kamal Arifin, Mat Piah, et al.
Published: (2018)

Influence of Process Variables on The Density of Aluminium Chip-Base Feedstock Prepared for Non-Melted Hot Extrusion Recycling
by: Wagiman, Abdullah, et al.
Published: (2024)

Sintering behavior of hydroxyapatite prepared from different routes
by: Ramesh, Singh, et al.
Published: (2012)

Sintering behavior of hydroxyapatite ceramics prepared by different routes
by: Yong, T.C., et al.
Published: (2010)

Sintering behaviour of hydroxyapatite prepared from different routes
by: S., Ramesh, et al.
Published: (2012)

Preparation and characterization of porous hydroxyapatite through polymeric sponge method
by: Iis, Sopyan, et al.
Published: (2009)

Banana Fiber Strands–Reinforced Polymer Matrix Composites
by: Beg, M. D. H., et al.
Published: (2016)

Sintering properties of hydroxyapatite powders prepared using different methods
by: Ramesh, S., et al.
Published: (2012)

Optimization of kenaf biomass's pre-treatment for polylactic acid's monomer production
by: Seeni Mohamed, Nurhafizah, et al.
Published: (2011)

Characterisation of Titanium Foams Sintered at Different Temperatures Prepared by the Slurry Method
by: Ahmad, Sufizar, et al.
Published: (2010)

High performance blended membranes using a novel preparation technique
by: Idris, Ani, et al.
Published: (2008)

Preparation of porous alumina for biomedical applications through protein foaming-consolidation method
by: Ahmad, Fadli, et al.
Published: (2009)

Characterization of forsterite bioceramics
by: Lee, K.Y., et al.
Published: (2012)

Evaluation of ABS hollow & solid pattern for the production of long stem hemi
by: Subramaniam, Baby Priyadharshini
Published: (2013)

Preparation of tin oxide (SnO2) thin films using thermal oxidation
by: Nuraini, Abdullah, et al.
Published: (2018)

SMR/ENR50/PVC ternary blends : preparation, blending characteristics and compatibilization studies
by: Wan Abdul Rahman, Wan Aizan
Published: (1997)

Cadangan bagi membangunkan sistem pengangkutan ringan halaju rendah jenis "articulating" bagi kegunaan membawa pelawat di UTM
by: Abdul Aziz, Azhar
Published: (2004)

Design and development of Acrylic Die for producing wax pattern to gabricate hip bone joint
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Rheological properties of SS316l MIM feedstock prepared with different particle sizes and powder loadings
by: M. Amin, Sri Yulis, et al.
Published: (2009)

Preparation of nano-structured manganese doped-biphasic calcium phosphate powders via sol-gel method
by: Iis, Sopyan, et al.
Published: (2009)