Drilling cutting removal in inclined anuli - A review

Drilling cutting removal in inclined anuli - A review

This paper discusses the assesment of efficient vertical hole cleaning in relation to study deviated hole cleaning. Refer attached article for detail discussion.

Bibliographic Details
Main Author:	Md. Yassin, Abu Azam
Format:	Article
Language:	English
Published:	Faculty of Chemical & Natural Resources Engineering 1987
Subjects:	T Technology (General)
Online Access:	http://eprints.utm.my/6739/1/AbuAzamMd.Yassin1987_DrillingCuttingRemovalInInclinedAnuli.pdf

Similar Items

Formation damage during drilling and completion practices - a review
by: Md. Yassin, Abu Azam
Published: (1988)

Palm oil diesel as a base fluid in formulating oil based drilling fluid
by: Md. Yassin, Abu Azam, et al.
Published: (1991)

Evaluation of formation damage caused by drilling fluid in deviated wellbore
by: Md Yassin, Abu Azam, et al.
Published: (1993)

Simulation of Drill Cuttings Dispersion and Deposition in South China Sea
by: Hock, Lye Koh, et al.
Published: (2011)

Optimizing cutting parameters in inclined end milling for minimum surface residual stress - Taguchi approach
by: Masmiati, N., et al.
Published: (2015)

Nanosilica-enhanced water-based drilling mud for hole cleaning in inclined wells
by: Boyou, Natalie Vanessa
Published: (2023)

Polymer nanocomposites application in drilling fluids: A review
by: Oseh, Jeffrey Onuoma, et al.
Published: (2023)

Lightweight biopolymer drilling fluid for underbalanced drilling: An optimization study
by: Nee, L.S., et al.
Published: (2015)

Optimization of parameters of laser non-linear inclined cutting on stainless steel metal
by: Abbas, Abbas Allawi
Published: (2014)

Study of scale formation in oil reservoir during water injection-A review
by: Merdhah, Amer Badr, et al.
Published: (2007)

Literature review of the benefits and obstacle of Horizontal Directional Drilling
by: Md. Salleh, Mohd. Norizam, et al.
Published: (2017)

Viscoplastic Modeling of a Novel Lightweight Biopolymer Drilling Fluid for Underbalanced Drilling
by: Khalil, M., et al.
Published: (2012)

Surgical drill bit design and thermomechanical damage in bone drilling: A review
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2021)

Optimization of cutting parameter for the drilling of medium density fiberboard / Muhammad Azhanudin Borhan
by: Borhan, Muhammad Azhanudin
Published: (2010)

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates
by: Abd Halim, Nor Farah Huda, et al.
Published: (2011)

The importance of infill drilling in a mature offshore field
by: Ismail, Issham
Published: (1991)

PCB drilling using arduino
by: Tan, Kee Kian
Published: (2015)

Air-Drill With Accelerometer And Microphone For Composite Drilling Application
by: Wei Tong, Koh
Published: (2022)

Natural convection in a porous trapezoidal enclosure with an inclined magnetic field
by: Saleh, H., et al.
Published: (2011)

A signal processing of deep drilling process
by: Muhamad Afiq Naqiuddin, Kamarizan
Published: (2015)

Using Finite Element simulation to investigate the effect of cutting edge radius on burr formation for inclined dimple milling operation
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2023)

Skop penyelidikan di Jabatan Kejuruteraan Petroleum
by: Md. Yassin, Abu Azam
Published: (1988)

Legislation on oil pollution prevention and control during petroleum production
by: Md. Yassin, Abu Azam
Published: (1988)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Composite Drilling Monitoring System
by: Ruddin, Putri Annur Khaleeda Amer
Published: (2019)

The use of Malaysian ilmenite as weighting material in drilling mud
by: Idris, Ahmad Kamal, et al.
Published: (1994)

Numerical simulation of metal removal in laser drilling using meshless local Petrov–Galerkin collocation method
by: Abidou, Diaa, et al.
Published: (2018)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
by: Ahamed, Ahmad Fauzi
Published: (2010)

An optimization technique on ultrasonic and cutting parameters for drilling and deep drilling of nickel-based high-strength Inconel 738LC superalloy with deeper and higher hole quality
by: Baghlani, V., et al.
Published: (2016)

Water-based mud formulations in drilling Terengganu shale formation
by: Ismail, Abdul Razak, et al.
Published: (1995)

Environmental Baseline Survey and Assessment for DrillingCutting Disposal in Makasar Strait: Effect on plankton and benthos communities
by: , Tjut Sugandawaty Djohan
Published: (2004)

Potential of surfactant washing to solve drilling waste environmental problems offshore
by: Muherei, M. A., et al.
Published: (2007)

Incline wheelchair
by: Tam, Kwan Yuen
Published: (2012)

Effect of cutting parameters on surface roughness in dry drilling of AISI D2 tool steel by using Taguchi Method
by: M.H. Osman1, M.H. Osman1, et al.
Published: (2018)

The study of laser drilling of polymeric material
by: Mohd Khairi Azri, Shapie
Published: (2013)

Wear Analysis On Different Customized Twist Drill Bit Designs In Drilling Cfrp Panel
by: Hashimi, Nur Hatin Raihana
Published: (2021)

Drilling of bone: thermal osteonecrosis regions induced by drilling parameters
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Improvement in the transport capacity of drilled particles of aqueous-based drilling fluid using surface-enriched hydroxyapatite nanoparticles
by: Oseh, Jeffrey O., et al.
Published: (2024)

Study of cutting force and surface roughness on drilling stainless steel 316L under various coolant condition
by: Kamdani, K., et al.
Published: (2018)

Caputo-fabrizio fractional derivative for magnetic blood flow of Newtonian and casson fluid in an inclined artery
by: Jamil, Dzuliana Fatin
Published: (2022)