-
3481
Performance evaluation of the fresh and hardened properties of different PVA-ECC mixes: An experimental approach
Published 2023-07-01“…It has been revealed through experimental results that the workability of all the mixes decreased with the increasing percentages of fibres, however, it remained within the allowable range of ASTM for fibre contents of up to 2%. It was further observed that the ductile behaviour of ECC was greatly compromised with the use of coarse aggregate in the mix, however, strain hardening and multiple-cracking properties were found to remain intact. …”
Get full text
Article -
3482
Petrographic and Physiomechanical Investigation of Late Cretaceous Kawagarh Formation Kahi Section, Nizampur Basin
Published 2022-01-01“…Aggregate degradation tests including water absorption, specific gravity, aggregate impact value, Los angles abrasion, and soundness was also computed according to the International standard organization, ASTM (American Society for testing materials) and British standard. …”
Get full text
Article -
3483
Experimental Study of Crack Propagation through Cladded 316L/S355 Steel Produced by the Hot-Roll Bonding Process
Published 2023-07-01“…The shear strength always satisfied the requirements of ASTM A264. It was observed that the concentration of oxide particles influenced the shear strength strongly. …”
Get full text
Article -
3484
Increasing Impact Strength of a Short Glass Fiber Compression Molded BMC by Shortening Fibers without Change in Equipment
Published 2022-02-01“…Specimens were cut from square panels in a spiral configuration in conformity with ASTM D 6110-02 for orthotropic panels, the flow direction approximately radially outward from the charge. …”
Get full text
Article -
3485
Evaluation of Jordanian Basalt as a Thermal Insulation Material
Published 2024-05-01“…Porosity and density were measured by the standards of the American Society of Testing Materials (ASTM). The chemical composition of the samples was analyzed by X-Ray diffraction to include the effect of aluminum oxide on thermal conductivity analysis. …”
Get full text
Article -
3486
Production and evaluation of activated carbon from Saudi Arabian Acacia Tortilis tree bark by microwave and low temperature activation process
Published 2023-12-01“…Characterization of produced activated carbons performed by proximate analysis adopting ASTM standard procedures. BET-specific surface area, total ash content, bulk density, moisture content, pH, pore volume and iodine number were determined. …”
Get full text
Article -
3487
Sorption of Acid Orange 3 From Aqueous Solution Using Eggshell
Published 2020-12-01“…Eggshell as a sorbent was prepared at laboratory temperature and pulverized by standard ASTM sieves in two sizes (50 and 140). The concentration of dye in the synthetic wastewater was 25 mg/L. …”
Get full text
Article -
3488
Numerical stability analysis and geotechnical investigation of landslide prone area (the case of Gechi district, Western Ethiopia)
Published 2023-12-01“…Soil samples were taken and tested for grain size analysis, Atterberg limit, water content, unit weight of soil, specific gravity, and shear strength parameters, following ASTM procedures. Plaxis v 8.6 software was used to supplement the slope stability analysis. …”
Get full text
Article -
3489
Facilitating Solid Waste Handling System in Port Harcourt Cosmopolis
Published 2022-10-01“…The methodology and procedure for this investigation obtained using vehicle selection approach centered on ASTM D5321 standard test method for ascertaining the constituents of municipal solid waste. …”
Get full text
Article -
3490
-
3491
Implications of the Use of Biodiesel on the Longevity and Operation of Particle Filters
Published 2022“…Na + K and Ca + Mg (also biodiesel production byproducts) are regulated by ASTM-D6751 standards (American Society for Testing and Materials) to be less than 5 ppm for B100; however, the literature gives examples of physical and chemical degradation of automotive emissions catalysts and their substrates with these Na and K residuals. …”
Get full text
Article -
3492
Investigation of cavitation erosion of high vanadium alloyed powder-metallurgy tool steel
Published 2020“…The specimens were tested using the ASTM G32-16 set up where an ultrasonic transducer was used to create cavitation impingement on the surface of the specimen. …”
Get full text
Final Year Project (FYP) -
3493
Biomechanics study on running shoes with different mechanical properties
Published 2021“…However, in the late 1990s, a new form of mechanical testing, the dynamic impact test (ASTM F1976), was introduced because of discrepancies with static shore hardness tests. …”
Get full text
Final Year Project (FYP) -
3494
Static compression test of materials
Published 2021“…Through reading and understanding with the American Society for Testing and Materials (ASTM) international standards, in portion the Standard Test Method for Measuring Metallic Materials at Room Temperature (E9-19), follow required dimensions for test specimens and use precise experimental instruments in lab to achieve the accurate results on this project. …”
Get full text
Final Year Project (FYP) -
3495
Robust multifunctional microcapsules with antibacterial and anticorrosion features
Published 2021“…The fabricated microcapsules show antibacterial properties against Escherichia coli, Vibrio coralliilyticus and E. aestuarii, as revealed from the standard ASTM E2315 time-kill test. Multifunctional coatings with both antibacterial and anticorrosion features were fabricated by incorporating the fabricated microcapsules both onto and into the epoxy coatings. …”
Get full text
Journal Article -
3496
Experimental investigation on the strength and stiffness of 3D printed stainless steel S/S-316L parts
Published 2023“…In this project, 12 specimens (three Tensile subsize, eight Fatigue) were fabricated under the American Society for Testing Material (ASTM) standard. Direct Metal Laser Sintering (DMLS) was the chosen additive manufacturing technology. …”
Get full text
Final Year Project (FYP) -
3497
Static compression test of materials
Published 2023“…Strictly following with the American Society for Testing and Materials (ASTM) International Standards, particularly the Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature E9-19, especially for the specimen dimension and testing procedure that needs to be followed in order to attain a more accurate and precise test result. …”
Get full text
Final Year Project (FYP) -
3498
Laser-based 3D printing of pure NI powders
Published 2019“…It falls under powder bed fusion category according to ISO/ASTM. This technology allows the production of near full dense metal parts (>99% relative density) with complex shape and geometry in a relative short amount of time and other resources, as compared to traditional metal manufacturing methods. …”
Get full text
Final Year Project (FYP) -
3499
Additive manufacturing of Inconel 625 superalloy parts via high pressure cold spray
Published 2018“…The bond strength between coating and substrate was tested according to ASTM C633. The hardness tests for both the substrate and the as-sprayed coating were conducted. …”
Get full text
Get full text
Conference Paper -
3500
Development and Evaluation of a Water-Based Flame Retardant Spray Coating for Cotton Fabrics
Published 2018“…The effectiveness of PApP in improving the flame retardant properties like ignition resistance and lateral flame spread were evaluated in accordance with ASTM D6413 and BS EN ISO 15025 flammability tests. …”
Get full text
Get full text
Journal Article