-
2801
Facile Coating of HAP on Ti6Al4V for Osseointegration
Published 2021-06-01“…FTIR and SEM confirm the formation of HAP and its presence after the immersion in SBF. Vicker hardness tester confirms the increase in hardness value of coated samples up to 35%. …”
Get full text
Article -
2802
Dry sliding tribological behavior of AZ31-WC nano-composites
Published 2019-06-01“…Micro-hardness values of as-cast composites are obtained through Vicker's micro-hardness tester. Friction and wear behavior of fabricated composites are studied using pin-on-disk type tribotester at room temperature under dry sliding condition. …”
Get full text
Article -
2803
Depletion of CD25+ regulatory cells results in suppression of melanoma growth and induction of autoreactivity in mice.
Published 2002Journal article -
2804
Development and Calibration of Thermoelectric-Power-Based Non Destructive Evaluation (TNED) Device for Aging Analysis of Carbon Steel SA 106B
Published 2023-12-01“…The correlation between thermoelectric power (TEP) and Vicker hardness (HV) [TEP (µV/oC) = ~2x10-5 Hardness (HV) + 0.008] has been analyzed. …”
Get full text
Article -
2805
-
2806
Experimental investigation of hot-wire laser deposition for the additive manufacturing of titanium parts
Published 2022-01-01“…Finally, the suitable hot wire laser welding parameters should be 0.183 cm s ^−1 for the welding speed, the wire current of 40 A, and the wire feeding speed of 1.00 m min ^−1 are 0.183 cm s ^−1 for welding speed, 40 A for wire current, and 1.00 m min ^−1 for wire feeding speed, which will give the average Vicker microhardness of 321.00–345.80 HV, the average tensile strength of 432.02 MPa (substrate); 670.30 MPa (horizontal direction), 497.39 MPa (vertical direction).…”
Get full text
Article -
2807
Structure-property relationships of iron-hydroxyapatite ceramic matrix nanocomposite fabricated using mechanosynthesis method
Published 2015“…Its mechanical properties were investigated by micro-Vicker's hardness and compression tests. Results showed that milling time directly influenced the characteristics of the nanocomposite powders. …”
Get full text
Article -
2808
-
2809
-
2810
-
2811
-
2812
Characterisation of Shigella Spa33 and Thermotoga FliM/N reveals a new model for C-ring assembly in T3SS
Published 2015Journal article -
2813
Evaluation of the mechanical properties of high impact denture base resin with different polymer to monomer ratios: An In vitro study
Published 2017-01-01“…The samples were tested for flexural strength, Vicker's hardness number (VHN) and impact strength. …”
Get full text
Article -
2814
Pre-eclampsia during pregnancy and risk of endometrial cancer: a systematic review and meta-analysis
Published 2023-05-01Get full text
Article -
2815
Influence of volume of endodontic irrigants used in different irrigation techniques on root canal dentin microhardness
Published 2021-01-01“…The RCDM was measured after root canal instrumentation and after final irrigation using Vicker microhardness tester (coronal, middle, and apical third). …”
Get full text
Article -
2816
Alcohol Use and the Risk of Colorectal Liver Metastasis: A Systematic Mapping Review
Published 2023-02-01Get full text
Article -
2817
-
2818
The Effects of Two Root Canal Irrigants and Different Instruments on Dentin Microhardness ( In Vitro Study)
Published 2011-04-01“…Materials & methods: The teeth divided in to four groups according to the type of irrigating solutions that used during root canal instrumentation with the use of normal saline as a control group, then each group sub divided in groups according to the instrument used in the root canal preparation, then after irrigation and preparation the roots sliced and root dentin microhardness measured using Vicker,s microhardness machine. Results: The result of this study showed that the type of instrument and Chlorhexidine have no effect on the microhardness of root canal dentin while Sodium Hypochlorite significantly decrease the microhardness of root canal dentin especially when use with Stainless Steel K-files and Nickel-Titanium K-files than when used with rotary Nickel-Titanium files. …”
Get full text
Article -
2819
-
2820