-
1
Flow investigation in a centrifugal pump
Published 2010“…A computational fluid dynamics analysis of a centrifugal blood pump model using ANSYS CFX 12.0 was conducted in this study. …”
Get full text
Final Year Project (FYP) -
2
Effects of geometrical parameters on performance of miniature centrifugal pump
Published 2014“…The results obtained in the present study provide us guidelines on the design and performance study of miniature centrifugal pump.…”
Get full text
Thesis -
3
Two-dimensional design and analysis of centrifugal blood pump impeller
Published 2008Get full text
Thesis -
4
Computer aided design and manufacture of centrifugal and axial flow fans
Published 2011Get full text
Research Report -
5
Simulation and experimental investigations for noise reduction in a small centrifugal high speed turbomachinery /
Published 2017software, multimedia -
6
Simulation and experimental investigations for noise reduction in a small centrifugal high speed turbomachinery /
Published 2017software, multimedia -
7
Large-scale flow measurements and analysis for radial inlets of industrial centrifugal compressors based on multi-hole probe system
Published 2021“…Furthermore, this auto-measuring system has been applied in the large-scale measurements on different radial inlets for industrial centrifugal compressors, which provide valuable flow information that was not previously available for industrial productions and assist with the improvement study. …”
Get full text
Journal Article -
8
Fully converged integral cross sections of collision induced dissociation, four-center, and single exchange reactions, and accuracy of the centrifugal sudden approximation in H2 + D2 reaction
Published 2013“…The initial state selected time-dependent wave packet method was employed to calculate the integral cross sections for the H2 + D2 reaction with and without the centrifugal sudden (CS) approximation by including all important K (the projection of the total angular momentum on the body-fixed axis) blocks. …”
Get full text
Get full text
Journal Article -
9
RES.12-001 Topics in Fluid Dynamics, Fall 2021
Published 2024Subjects: Get full text
Learning Object -
10
RES.12-001 Topics in Fluid Dynamics, Spring 2010
Published 2023Subjects: Get full text
Learning Object -
11
Scalable mesenchymal stem cell enrichment from bone marrow aspirate using deterministic lateral displacement (DLD) microfluidic sorting
Published 2024“…Conventional MSC harvesting from BMA relies on archaic centrifugation methods, often leading to poor yield due to osmotic stress, high centrifugation force, convoluted workflow, and long experimental time (∼2–3 hours). …”
Get full text
Article -
12
Fabrication of fine features using digital light processing stereolithography
Published 2015“…On the other hand, the feasibility of centrifugation as a post process was studied and appropriate fixture was designed. …”
Get full text
Final Year Project (FYP) -
13
Engineering a surface to enhance endothelial cell adhesion towards creating a 'roll-up' blood vessel prosthesis
Published 2013“…Firstly, cell adhesion on the modified surface of electrospun Polycaprolactone (PCL) fibers improved significantly, after verification using the centrifugation assisted cell adhesion assay. Human umbilical vein endothelial cell (HUVEC) adhesion was found to be highest on gelatin crosslinked to NaOH hydrolyzed electrospun PCL fibers before and after centrifugation, based on cell attachment observation under the fluorescent microscope and mitochondrial activity quantification using AlamarBlue®. …”
Get full text
Final Year Project (FYP) -
14
Chemical synthesis of graphene oxide and graphene
Published 2010“…The size selection process was conducted using conventional sedimentation centrifuge technique. Each solution was subjected to 3 centrifugation processes, and the rounds per minute (rpm) used were 3000pm, 6000rpm and 9000rpm. …”
Get full text
Final Year Project (FYP) -
15
Identification of major triglycerides causing the clouding of palm olein
Published 1994“…Clouding was obtained by storing palm olein at 12.5°C for up to 24h and was separated by centrifugation. the fat crystals were collected after washing with cold acetone. …”
Article -
16
Optimization of methodology for EPS extraction and analysis
Published 2010“…It was found that low centrifuge speed of 2000 rpm and 4000 rpm will cause biomass re-suspension. …”
Get full text
Final Year Project (FYP) -
17
Purification, crystallization and structure determination of Thermotoga maritima CorA Magnesium transporter.
Published 2010“…We have also experimented purifying TMCorA by heating and centrifugation only. This form of purification has produced a relatively pure sample and formed crystals in the presence of lipids. …”
Get full text
Final Year Project (FYP) -
18
Noble metal and enzymatic catalysts for plating and biofuel cell
Published 2018“…The project also presents a novel centrifugation compression method developed and demonstrated to be effective in the immobilization of enzyme and redox mediator within the carbon matrix for glucose oxidation and oxygen reduction reaction. …”
Get full text
Thesis -
19
Crosslinked microneedle patch to extract interstitial fluid for diagnosis
Published 2017“…After extraction of analytes, we could also easily recover the analytes for analysis by centrifugation with DI water. MeHA microneedles are also biodegradable, biocompatible and non-immunogenic which negates the risk of irritation or inflammation. …”
Get full text
Final Year Project (FYP) -
20
Towards an optimal and unbiased approach for tumor cell isolation
Published 2013“…We present a negative enrichment approach, integrating WBC depletion and chemical-free RBC depletion in the same setup without the need for centrifugation, washing or multiple sample handling steps. …”
Get full text
Get full text
Journal Article