Positive pressure induced channeled suction cups by Yang, Shannon X. (Shannon Xuan)

Get full text

Static, dynamic and buckling analyses of 3D FGM plates and shells via an isogeometric-meshfree coupling approach by Tan, Pengfei, Nguyen-Thanh, Nhon, Rabczuk, Timon, Zhou, Kun

“…The meshfree method and IGA are coupled using the higher-order consistency condition in the physical domain so that the higher-order continuity of basis functions is guaranteed, and the topological complexity of the global volumetric parameterization for IGA to build the 3D geometry can be overcome. By employing IGA elements on the domain boundary and meshfree nodes in the interior domain, the approach preserves the advantages of the exact geometry and flexible discretization in the problem domain. …”
Get full text
Get full text

Investigation of leakage flow in compressor clearances by Lim, Li Ying

“…Parametric studies were also conducted to investigate the effect of varying rotor geometry and pressure ratio on end face leakage, as well as the effect of varying radial clearance height and pressure ratio on radial clearance leakage. …”
Get full text

Data-driven collision risk assessment to redefine no-fly zone boundaries around aerodromes by Tan, Qian Yi

“…This report aims to study the efficiency of current No-Fly Zones (NFZs) for Unmanned Aerial Vehicles (UAVs) around aerodromes, in terms of the suitability of their size and geometry. It is proposed that the NFZ geometry around aerodromes should be similar to the aerodrome’s runway(s), due to the expectation that low-flying aircraft occupying the same elevation as a commercial or civilian UAV will be either taking off or landing on a runway, thus a higher risk of UAV-manned aircraft collision exists near the runways. …”
Get full text

Investigating the material properties of 3D printed aerospace components by Tai, Hao Xiang

“…With such complexities in blade geometry, blade fabrication poses a challenge to manufacturers. …”
Get full text

Design of novel nozzles for higher interlayer strength of 3D printed cement paste by He, Lewei, Tan, Jolyn Ze Mei, Chow, Wai Tuck, Li, Hua, Pan, Jiahui

“…In addition, the interface shaper and the side trowel are able to further enhance the interlayer strength significantly by up to 2 times, through optimization of the interfacial geometry and minimization of the interlayer notch of 3D printed cement paste. …”
Get full text

Diffuse correlation spectroscopy. by Low, Wei Ching.

“…This project aims to study the fundamentals of DCS in three stages: (i) Tissue phantom construction, (ii) Intensity fluctuation measurements to acquire the temporal field autocorrelation function, g1(τ) and (iii) Monte Carlo Simulation of photon propagation in pre-defined, tissue-mimicking geometry. In the making of tissue phantom, titanium (iv) oxide (TiO2) and carbon black were used as a scattering and absorbing agent respectively. …”
Get full text

Improving helmet design for reducing head injuries through finite element analysis by Ng, Sherlene

“…The model was subjected to different loading conditions, materials, and geometry design parameters, followed by the analysis of the results using statistical methods. …”
Get full text

Atomistic simulation of EELS of SiON/Si interface and SiON breakdown by Wang, Zhongrui.

“…An analytic solution of the Hertz potential vector for arbitrary 1-Dimensional geometry has been obtained to simulate and interpret the Si/SiOx spectrum under the influence of thickness of central oxide region, thickness of the side Si region as well as the interaction of surface plasmons. …”
Get full text

Implementing design tools for military vehicles in an open-source computer-aided engineering framework by Tan, Young Kiat Zenn

“…The input files and Python code are all in human-readable format, facilitating verification and tailoring to specific needs. Vehicle geometry analyses can be conducted in FreeCAD, or the geometry representing the accommodation models can be exported via a variety of file formats, including IGES and STEP, for use in other computer-aided engineering software systems.…”
Get full text

Finite Element Analysis Of Temperature Field In Selective Laser Melting Process by Tan, Peng Fei, Li, Ying Li, Zhou, Kun

“…Peeling has been qualified by means of a truncated inverted cone as test geometry. As the cross-sectional diameter of the cone increase throughout the build-job, the geometry will release from the glass based build platform at the point where the peeling force exceed the adhesion force between platform and part. …”
Get full text
Get full text

A self-peeling vat for improved release capabilities during DLP materials processing by Pedersen, David Bue, Zhang, Yang, Nielsen, Jakob Skov, Hansen, Hans NØrgaard

“…Peeling has been qualified by means of a truncated inverted cone as test geometry. As the cross-sectional diameter of the cone increase throughout the build-job, the geometry will release from the glass based build platform at the point where the peeling force exceed the adhesion force between platform and part. …”
Get full text
Get full text

The effects of dub-off angle on chip evacuation in single-lip deep hole gun drilling by Wan, S., Tnay, Guan Leong, Woon, Keng Soon, Yeo, Swee Hock

“…In gundrilling, the efficiency in evacuating chips is governed by the geometry of gun drills that defines the hydraulic boundary conditions for coolant and chip flow. …”
Get full text
Get full text

A local characterization of the graphs of alternating forms and the graphs of quadratic forms over GF(2) by Munemasa, A., Pasechnik, Dmitrii V., Shpectorov, Sergey V.

Get full text
Get full text

Compact handheld digital holographic microscopy system development by Sui, Liansheng, Singh, Vijay Raj, Anand, Asundi

“…The concept is based on lensless magnification using diverging wave geometry and the miniaturized optical design which provides a compact packaged system. …”
Get full text
Get full text

Nanofluidic devices and their applications by Abgrall, Patrick, Nguyen, Nam-Trung

“…Beyond this, the control on the geometry allows smarter design resulting, among others, in new separation principles by taking advantage of the anisotropy. …”
Get full text
Get full text

Tree stability in an improved soil to withstand wind loading by Sim, E. K., Harnas, F. R., Rahardjo, Harianto, Leong, Eng Choon, Tan, Puay-Yok, Fong, Yok-King

“…Factors investigated include root geometry and soil shear strength parameter. Finite element results showed good agreement with static analysis in determining the maximum wind force needed to uproot the tree. …”
Get full text
Get full text

A study of the effectiveness of adapting Fused Deposition Modelling (FDM) in industrial design process / Firdaus Zawawi by Zawawi, Firdaus

“…The case studies focus on six important factors derived from Peschges (1999) research: 1) Preciseness, 2) Surface Quality, 3) Cost Corridor, 4) Time, 5) Suitability for Geometry and 6) Practical Features. The findings showed that they produced durable prototype, which are smooth surfaced and complete layer, thin layer, with cost savings and reduce build time, as well as wide suitability for geometry, practical features achieved by improving surface quality through sanding, polishing and painting the prototype. …”
Get full text

Thermal characteristics and emissions of gaseous fuel flameless combustion with tangential air inlet by Ali Abuelnuor, Abuelnuor Abdeen

Get full text

Effect of phase-based instruction using geometer's sketchpad on geometric thinking regarding angles by Poh, Geik Tieng, Leong, Kwan Eu

“…Teaching and learning geometry is not merely about memorising geometrical properties but about grasping the conceptual understanding of geometry as well. …”