Using Optical Imaging and Image Processing to Verify a Layer in a Laser Powder Bed Fusion Process by Kota, Maya Padmini

“…Additive manufacturing (AM) allows for the creation of complex geometries that cannot be created with traditional manufacturing methods. …”
Get full text

Substrate resistance extraction using a multi-domain surface integral formulation by Vithayathil, Anne M. (Anne Marie), 1978-

Get full text

Robust distribution sensor network localization with noisy range measurements by Moore, David Christopher, 1981-

Get full text

A generalized precorrected-FFT method for electromagnetic analysis by Leibman, Stephen Gerald

Get full text

Computational mass transfer moduling of flow through a photocatalytic oxygen generator by Köksal, Erin (Erin Sevim)

Get full text

Ceramic microforming process by Rosenthal, Matthew E. (Matthew Eric), 1971-

Get full text

Additive assembly of digital materials by Ward, Jonathan (Jonathan Daniel)

Get full text

Microfluidic Platforms for Studies of Angiogenesis, Cell Migration, and Cell–Cell Interactions by Chung, Seok, Sudo, Ryo, Vickerman, Vernella Velonie V., Zervantonakis, Ioannis, Kamm, Roger Dale

Get full text
Get full text

Critical assessment of thorium reactor technology by Drenkhahn, Robert (Robert A.)

Get full text

Finite difference techniques for body of revolution radar cross section by Pacheco, Joe, 1978-

Get full text

Focal Mechanism Determination of Induced Microearthquakes in an Oil Field Using Full Waveforms from Shallow and Deep Seismic Networks by Li, Junlun, Kuleli, Huseyin Sadi, Zhang, Haijiang, Toksoz, M. Nafi

“…For different hypocenters and source types, comprehensive synthetic tests show that our method is robust to determine the focal mechanisms under the current array geometries, even when there is considerable velocity inaccuracy. …”
Get full text

Development of perfusable organ-on-chip with curved microchannel by Tan, Sakina Jin Swan

“…While several vascular organ-on-chip platforms have been reported, there are still limited studies that construct multi-layered arterial wall structure, and with relevant vessel geometries (e.g., circular lumen) for perfusion studies. …”
Get full text

Numerical simulation of selective laser melting process by Ang, Jing Kang

“…Selective laser melting has aroused growing interest in both scientific and industrial endeavors over the past decades, due to its capability to fabricate metal components with complex geometries. As a cost effective alternative, simulation software enables the users to analyze different processes without physically running the experiments which might incur additional cost and time. …”
Get full text

3D printing of asymmetric re-entrant structures for microfluidics by Lim, Yu Fong

“…In contrast, 3D printing offers rapid prototyping and intricate geometries, especially beneficial for asymmetric re-entrant structures. …”
Get full text

Thermoelastic fracture mechanics analysis on electronic packaging using boundary element method by Kuek, Choon Han.

“…The Boundary Element Method was used to analyze the fracture behavior of a typical IC package under both mechanical and thermal loads. The geometries and aspect ratios of the IC package were varied and its effects on the structural integrity of the IC package were analyzed. …”
Get full text

Thermal management of integrated electronics by Koh, Sheilina Yu Fang

“…Through this report, the author will present the thermal management technique chosen and discuss the results obtained with the use of micropillar arrays. Different geometries (e.g. micropillar height, pitch, diameter and array length) fabricated on wick length of 1.0 cm were investigated. …”
Get full text

Experimental measurement of squeeze flow in hydrodynamics bearings by Xing, Fei

“…The spiral length of K15 (Alan) is almost twice than that of 2 other SGB. The geometries parameter of 3 SGB are shown in Table 3-1. …”
Get full text

Investigation on the mechanical behaviour of 3-D printed lattice sandwich structures by Ng, Bjorn Chong Yu

“…However, recent advancements in additive manufacturing have allowed for the fabrication of sophisticated designs and geometries of cellular lattice structures to a significantly high level of accuracy. …”
Get full text

Thermal performance of a cold plate with 3D-printed porous inserts by Kam, Shaun Jian En

“…The investigation nonetheless shows that the porous structures fabricated by additive manufacturing have better thermal performance as compared to the commercial foams available in the market today. However, the geometries of the porous structures may not have been optimised and further studies could develop higher potential to 3D printed porous inserts as a means of enhancing heat transfer of a cold plate.…”
Get full text

Effects of dielectric flow rate in electrical discharge machining of aerospace materials by Law, Kai Rong

“…Furthermore, increasing flushing pressure leads to lower electrode tool wear but at the same time, it results in poorer workpiece surface geometries.…”
Get full text