Showing 421 - 440 results of 528 for search '"operational amplifier"', query time: 0.20s Refine Results
  1. 421

    A 1.1 V 25 ppm/°C relaxation oscillator with 0.045%/V line sensitivity for low power applications by Liao, Yizhuo, Chan, Pak Kwong

    Published 2023
    “…The oscillator includes a stable two-transistor based voltage reference without an operational amplifier, a simple current reference employing the temperature-compensated composite resistor, and the approximated complementary to absolute temperature (CTAT) delay-based comparators compensate for the approximated proportional to absolute temperature (PTAT) delay arising from the leakage currents in the switches. …”
    Get full text
    Journal Article
  2. 422

    Gain-enhanced feedforward path compensation technique for pole–zero cancellation at heavy capacitive loads by Chan, Pak Kwong, Chen, Y. C.

    Published 2009
    “…The technique has been confirmed by the experimental results. An operational amplifier has been designed to drive a capacitive load of 300 pF. …”
    Get full text
    Get full text
    Journal Article
  3. 423

    On the Performance of an Aerosol Electrometer with Enhanced Detection Limit by Yixin Yang, Tongzhu Yu, Jiaoshi Zhang, Jian Wang, Wenyu Wang, Huaqiao Gui, Jianguo Liu

    Published 2018-11-01
    “…The model showed that the noise was a function of ambient temperature, and it was affected by the characteristics of feedback resistor and operational amplifier simultaneously. The Faraday cup structure of the aerosol electrometer was optimized by adopting a newly designed cup-shaped metal filter which increased the surface area of the cup; thus the particle interception efficiency was improved. …”
    Get full text
    Article
  4. 424

    The Design of a Low Noise and Low Power Current Readout Circuit for Sub-pA Current Detection Based on Charge Distribution Model by Dahai Jiang, Qinan Chen, Zheng Li, Qiang Shan, Zihui Wei, Jinjin Xiao, Shuilong Huang

    Published 2022-06-01
    “…The changes in the load state of the amplifier under different operating conditions and the influence of the gain of the operational amplifier (Opamp) on the trans-impedance gain are analyzed to improve the design theory of switched-capacitor trans-impedance amplifiers. …”
    Get full text
    Article
  5. 425

    Analysis, Simulation, and Development of a Low-Cost Fully Active-Electrode Bioimpedance Measurement Module by Christos Dimas, Vassilis Alimisis, Ioannis Georgakopoulos, Nikolaos Voudoukis, Nikolaos Uzunoglu, Paul P. Sotiriadis

    Published 2021-08-01
    “…A comparison study between four selected operational amplifiers (ADA4622, OPA2210, AD8034, and AD8672) is additionally performed. …”
    Get full text
    Article
  6. 426

    A 54 µW CMOS Auto-Trimming Bandgap References (ATBGR) Achieving 90 dB PSRR for Artificial Intelligence of Things (AIoT) Chips by Balamahesn Poongan, Jagadheswaran Rajendran, Selvakumar Mariappan, Arvind Singh Rawat, Narendra Kumar, Arokia Nathan, Binboga S. Yarman

    Published 2023-09-01
    “…The reference voltage, <i>V</i><sub>REF</sub>, is compared to an external constant value, 1.25 V, through an operational amplifier, and the output of the de-multiplexer is used to configure the PMOS switches. …”
    Get full text
    Article
  7. 427

    A CMOS PSR enhancer with 87.3 mV PVT-insensitive dropout voltage for sensor circuits by Zhang, Jianyu, Chan, Pak Kwong

    Published 2022
    “…Due to simplicity without voltage reference and operational amplifier(s), low power and small consumption of supply voltage headroom, the proposed work is very useful for supply noise sensitive analog or sensor circuit applications.…”
    Get full text
    Journal Article
  8. 428

    Design of chopper-stabilized amplifiers with reduced offset for sensor applications by Cui, J., Chan, Pak Kwong

    Published 2010
    “…A new resistance balancing circuit technique is also introduced, which permits further reduction of dc offsets in conventional chopping operational amplifier (op-amp) or chopping differential difference amplifier (DDA). …”
    Get full text
    Get full text
    Journal Article
  9. 429

    Embedded mini-analyzer device for in situ wide range heavy metal identification and concentration detection by Mazaheri, Amin

    Published 2018
    “…This potentiostat is designed with a fully differential operational amplifier and rail-to-rail common-mode range buffer for linearity of output signal. …”
    Get full text
    Thesis
  10. 430

    Performance evaluation of single-stage differential amplifier based on carbon nanotube by Voon, Vivian Li Sin

    Published 2022
    “…Differential amplifier circuit topology is applied in this research because it is a very useful operational amplifier circuit to examine the performance differences between carbon nanotube and conventional silicon when they are used as channel material by evaluating Common-Mode Rejection Ratio (CMRR) of differential amplifier. …”
    Get full text
    Thesis
  11. 431

    An 8-bit 200-MSample/s pipelined ADC with mixed-mode front-end S/H circuit by Jiang, Shan, Do, Manh Anh, Yeo, Kiat Seng, Lim, Wei Meng

    Published 2010
    “…The reduction of signal swings relaxes the operational amplifier (opamp) gain, slew rate, bandwidth, and capacitor-matching requirements in pipelined ADCs. …”
    Get full text
    Get full text
    Journal Article
  12. 432

    Design of CMOS potentiostat for low-concentration heavy metal detection by Raeisinafchi, Mehran

    Published 2015
    “…By using dTo ensure the linearity of output signal, the potentiostat is designed using fully differential operational amplifier and rail-to-rail common-mode range buffer. …”
    Get full text
    Thesis
  13. 433

    Classification of ankle joint movements based on surface electromyography signals by Al-Quraishi, Maged Saleh Saeed

    Published 2015
    “…In this part four EMG channels were implemented using instrumentation amplifier (INA114) for pre-amplification stage then the amplified signal was filtered using band pass filter to eliminate the unwanted signals. Operational amplifier (OPA2604) was involved for the main amplification stage to get the output signal in volts. …”
    Get full text
    Thesis
  14. 434

    CMOS low noise analog front-end design for multi-lead non-contact electrocardiogram by Chung, Wei Hong

    Published 2022
    “…From the simulation result, the CMOS operational amplifier design achieved the gain of 64.2286 dB and phase margin of 83.3°. …”
    Get full text
    Thesis
  15. 435

    Development of S-PWM voltage source inverter for induction motor drives by Siti Nursyuhada, Mahsahirun

    Published 2017
    “…A 3-phase sinusoidal waves, a Centre-aligned triangle wave, 3-phase S-PWM comparator modules are implemented with operational amplifier circuit configurations of specific ICs. …”
    Get full text
    Thesis
  16. 436

    A Fast Interface Circuit for the Measurement of 10 Ω to 1 GΩ Resistance by Yongkai Ning, Jiangfei Guo, Yangchen Jia, Duosheng Li, Guiliang Guo

    Published 2023-09-01
    “…In order to ensure that the current mirror can be copied accurately, this work uses a negative feedback structure consisting of an operational amplifier and an NMOS tube to ensure that the <inline-formula><math xmlns="http://www.w3.org/1998/Math/MathML" display="inline"><semantics><msub><mi mathvariant="normal">V</mi><mi>DS</mi></msub></semantics></math></inline-formula> of the current mirroring tube remains consistent. …”
    Get full text
    Article
  17. 437

    On-Line Detection Method and Device for Moisture Content Measurement of Bales in a Square Baler by Huaiyu Liu, Zhijun Meng, Anqi Zhang, Yue Cong, Xiaofei An, Weiqiang Fu, Guangwei Wu, Yanxin Yin, Chengqian Jin

    Published 2022-08-01
    “…Aiming to address the problems of low detection accuracy and poor stability due to the weak anti-interference ability of the bridge circuit and operational amplifier circuit, and the influence on the capacitance of the bulk density and temperature of the straw bale, an on-line detection device for the moisture content of straw bales in a square baler was developed based on the capacitance method. …”
    Get full text
    Article
  18. 438

    Digital Calibration of Input Offset Voltage and Its Implementation in FDDA Circuits by David Maljar, Michal Sovcik, Miroslav Potocny, Robert Ondica, Daniel Arbet, Viera Stopjakova

    Published 2023-11-01
    “…Then, the principle and overall design of the calibration subcircuit, which was generally used to calibrate the input offset voltage <inline-formula><math xmlns="http://www.w3.org/1998/Math/MathML" display="inline"><semantics><msub><mi>V</mi><mrow><mi>I</mi><mi>N</mi><mo>_</mo><mi>O</mi><mi>F</mi><mi>F</mi></mrow></msub></semantics></math></inline-formula> of the operational amplifier (OPAMP). The essence of this work is verification of the proposed digital calibration algorithm for minimization the <inline-formula><math xmlns="http://www.w3.org/1998/Math/MathML" display="inline"><semantics><msub><mi>V</mi><mrow><mi>I</mi><mi>N</mi><mo>_</mo><mi>O</mi><mi>F</mi><mi>F</mi></mrow></msub></semantics></math></inline-formula> of a bulk-driven fully differential difference amplifier (FDDA) with the power supply voltage <inline-formula><math xmlns="http://www.w3.org/1998/Math/MathML" display="inline"><semantics><msub><mi>V</mi><mrow><mi>D</mi><mi>D</mi></mrow></msub></semantics></math></inline-formula> = 0.4 V. …”
    Get full text
    Article
  19. 439
  20. 440