-
261
Wideband (22-30ghz) mm-wave substrate integrated waveguide (siw) antenna for 5g application
Published 2019“…In this paper, the SIW cavity slots antenna wideband millimeter-wave is proposed for fifth generation (5G) communication. The antenna also shows an average gain of 8,574 dBi, 20 x 20 mm2 compact. …”
Get full text
Conference or Workshop Item -
262
-
263
Report on the IBS best practice visit to Sydney, N.S.W., Australia 5th-10th June 2005
Published 2005Get full text
Monograph -
264
Comparison of uncoated and coated carbide inserts in end milling of Ti–6Al–4V in terms of surface roughness
Published 2008“…This paper compares and also optimizes the surface finish in end milling of titanium alloy Ti-6Al-4V using uncoated and PVD TiAlN coated carbide inserts under dry conditions. …”
Get full text
Article -
265
2-Bromo-4-(3,4-dimethyl-5-phenyl-1,3-oxazolidin-2-yl)-6- methoxyphenol
Published 2012Get full text
Article -
266
Isolation of 5,7-dihydroxy-8-methoxyflavone as an anti-hyperglycemic agent from the leaves of Tetracera indica MERR. (Mempelas)
Published 2011“…MEOH extract of the leaves of T. indica upon repeated coloumn choromatography and recrystallization techniques afforded a major phenolic compound viz., 5,7-dihydroxy-8-methoxyflavone (1.2 gm) (Fig. 1) which revealed significant anti-hyperglycemic activity comparable to GLBC in vivo. …”
Get full text
Proceeding Paper -
267
Assessment of performance of uncoated and coated carbide inserts in end milling of Ti-6Al-4V through modelling
Published 2011“…An effective approach has also been presented to optimize surface finish in milling Inconel 718 [5]. Kaye et al [6] used response surface methodology in predicting tool flank wear using spindle speed change. …”
Get full text
Book Chapter -
268
Tool life assessment in End Milling Titanium Alloy (Ti-6AI-4V) using PCD inserts
Published 2008“…The range which is used in this study for cutting speed, axial depth of cut, and feed, are 80.5 - 200 m/min, 05 - 2.0 mm, and 0.05 - 0.15 mm/tooth, respectively. …”
Get full text
Article -
269
Surface integrity in end milling titanium alloy Ti6Al4V under heat assisted machining
Published 2013“…This study presents the effects of heat assisted machining on the surface integrity during end milling of titanium alloy Ti-6A1-4V using uncoated tungsten carbide inserts. The effects of heating temperature on surface integrity are presented. …”
Get full text
Article -
270
Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
Published 2008“…The range which is used in this study for cutting speed, axial depth of cut, and feed, are 80.5-200 m/min, 0.5-2.0 mm, and 0.05-0.15 mm/tooth, respectively. …”
Get full text
Article -
271
Modeling the electrical parameters in EDM process of Ti6Al4V alloy using Neural Network method
Published 2013“…The experiments were planned and implemented using Central Composites Design (CCD) of Response Surface Methodology (RSM) with three input factors at five levels. The neural network model was built by using MATLAB. …”
Get full text
Article -
272
Assessments of time diversity rain fade mitigation technique for v-band space-earth link operating in tropical climate
Published 2013“…This paper outlines the likely improvement of a future V-band frequency space-Earth link using proposed time diversity (TD) technique. …”
Get full text
Article -
273
Extending the scope of proprietary remedies to recovery of pure profits from successful investment of bribes: the endgames in Lister v Stubbs
Published 2015“…For more than a century Lister v Stubbs (1890) 45 Ch D 1 stood as authoritative Court of Appeal judgment denying the recovery of profits acquired from the successful investment of gains obtained in breach of fiduciary duties. …”
Get full text
Proceeding Paper -
274
Lubricated wear behaviour of SiC reinforcement on TI-6AL-4V alloy based on Taguchi approach
Published 2016Subjects: Get full text
Proceeding Paper -
275
-
276
-
277
An innovative antenna array with high inter element isolation for sub-6 GHz 5G MIMO communication systems
Published 2022“…The proposed approach is demonstrated on a four-element array for 5G MIMO applications. Each radiating element in the array is constituted from a 3 × 3 matrix of interconnected resonant elements. …”
Get full text
Article -
278
Virtual antenna array for reduced energy per bit transmission at Sub-5 GHz mobile wireless communication systems
Published 2023“…The proposed four orthogonal 4-element VAA covers the entire sub-5 GHz frequency range, and it radiates bidirectional in the azimuth plane and omni-directional in the elevation plane. …”
Get full text
Article -
279
5G mobile wireless access and digital channeling with RF over fiber for long-haul 64-QAM communication
Published 2023“…Such high bit rates required by 5G systems for long-haul communication. This is accomplished by overcoming the limitation of single mode fibers (SMF) of power attenuation and chromatic dispersion. …”
Get full text
Get full text
Article -
280
High performance antenna system in MIMO configuration for 5G wireless communications over sub-6 GHz spectrum
Published 2023“…These characteristics make the proposed MIMO antenna system suitable for 5G communication systems.…”
Get full text
Article