-
661
Teachers’ interpretations on Task-Based Language Teaching (TBLT) in the inter-cultural English language classroom
Published 2011“…The findings on how teachers feel about the implementation of the methodology in line with their expectations on students at the end of a semester were presented. …”
Get full text
Proceeding Paper -
662
Developing an IT-based pre-course balancing programme for aviation students
Published 2005“…In line with Government targets to widen access to higher education in the UK (Clark, 2003; DfES, 2003), the Centre for Civil Aviation [CCA] at London Metropolitan University developed a Foundation Degree in Aviation Management & Operations, which was launched in September 2002. …”
Get full text
Article -
663
'Forget TV, it will never show you the experience of the victim': representations of rape in Mindhunter
Published 2019“…Media depictions of gendered violence often fall in line with negative stereotypes and rape myths. These depictions may influence public understandings of gendered violence and affect societal responses to victims and rape. …”
Get full text
Article -
664
Understanding the barriers and the possibilities : a study of people with disabilities and their lived experience of the labour market
Published 2023“…Collaboration between researchers at LMU and a Borough in London (Borough X or Council X) As in line with EA (2010) councils can set up employment support services and various schemes, and Council X was interested in knowing what works and what does no To get a better understanding of people with disabilities and their lived experience of the labour market To present policy suggestions for improving labour market participation and services based on the evidence collected…”
Get full text
Conference or Workshop Item -
665
-
666
Novel opto-electronic and plastic fibre sensors
Published 1998“…The middle POF is coupled to a red LED and emits light onto a flat target with the two outer fibres receiving the reflected light from the target and guiding it to two silicon PIN photodiodes. Theoretical investigations on the behaviour of the sensor are presented for ranges between 0 mm and 100 mm, and for targets with different reflectivities. …”
Get full text
Thesis -
667
Effect of intrapartum pethidine on the neonatal outcome: is it duration related?
Published 2012“…All neonates delivered with good Apgar Score (AS), 8 at 1 minute and 9 at 5 minute except 1 with AS of 5 at 1 min and 7 at 5 min which delivered more than 4 hours after pethidine. …”
Get full text
Get full text
Article -
668
-
669
-
670
-
671
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatography for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
672
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatographyn for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
673
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatography for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
674
Amalan penyeliaan pensyarah pembimbing terhadap pelaksanaan latihan industri di Politeknik Sultan Haji Ahmad Shah Kuantan, Pahang
Published 2014“…Dapatan kajian menunjukkan skor min konstruk pengetahuan, kemahiran dan sikap merupakan aspek yang berada pada tahap yang sederhana dari pensyarah pembimbing dan pelajar. …”
Get full text
Get full text
Get full text
Thesis -
675
Ultrasonic and electroplating approach for washcoat of γ-alumina and nickel oxide (nio) catalyst on fecral substrate for catalytic converter
Published 2018“…Therefore, an appropriate techniques and parameter is UB+EL 30 min used for coating FeCrAl CATCO potential to improve physical properties and reduce emission.…”
Get full text
Get full text
Get full text
Thesis -
676
Sugarcane green ceramic hollow fibre membrane for oily wastewater separation
Published 2018“…The newly-developed ss-CHFM/WSBA induced excellent wettability properties with contact angle value of 161.1° at 60 min of grafting time, 3 cycle of grafting cycle and calcination temperature at 400 °C. …”
Get full text
Get full text
Get full text
Thesis -
677
Performance comparison of differential evolution and particle swarm optimization in constrained optimization
Published 2012“…This paper presents a comparative study for min-max constrained optimization using PSO and DE. …”
Get full text
Article -
678
Physical and mechanical properties of Thermoplastic Natural Rubber (TPNR) nanocomposites
Published 2012“…Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). …”
Get full text
Article -
679
Investigation of burr in high speed microdrilling
Published 2013“…The desirability of getting the minimum burr height is72% and the optimum parameters are 30000 rpm spindle speed and 0.2 mm/min feed rate.…”
Get full text
Article -
680
Tool life in high speed turning with negative rake angle
Published 2011“…The present work studies some aspects of turning process applied on mild steel using cermets tools at high speed cutting (1000mm/min) by using negative rake angle (90 to 12). The influence of increasing the cutting speed and negative rake angle on flank tool wear, cutting force, feeding forces and tool temperature were analyzed. …”
Get full text
Article