-
201
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
202
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
203
-
204
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
205
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
206
Optimization of copper oxide film by dip coating technique for oxygen detection
Published 2018“…Based on the results, 400 oC annealing temperature, pH 12.0 of CuO solution and 70 mm/min of withdrawal speed are the optimum parameters of CuO films for gas detection. …”
Get full text
Get full text
Get full text
Thesis -
207
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
208
-
209
A comparative study of the effectiveness of β-glucosidase immobilized on CNT-nanoparticles and Ca-alginate beads
Published 2014“…The Michaelis constants, Km and Vmax, determined using Langmuir linearized plot are respectively 0.09048 μmol/mL and 0.00989 μmol/mL.min for immobilized Ca-alginate; and 0.0985 μmol/mL and 0.01237 μmol/mL.min for immobilized MWCNT. …”
Get full text
Get full text
Proceeding Paper -
210
Optimization of low-methoxyl pectin extraction from durian rinds and its physicochemical characterization
Published 2023“…DP powders were homogenous slab-like granules with smooth surfaces and had relatively good thermal properties. …”
Get full text
Article -
211
Optimization of low-methoxyl pectin extraction from durian rinds and its physicochemical characterization
Published 2023“…DP powders were homogenous slab-like granules with smooth surfaces and had relatively good thermal properties. …”
Get full text
Article -
212
Optimization of low-methoxyl pectin extraction from durian rinds and its physicochemical characterization
Published 2023“…DP powders were homogenous slab-like granules with smooth surfaces and had relatively good thermal properties. …”
Get full text
Article -
213
-
214
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
215
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
216
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
217
-
218
Synthesis-condition dependence of carbon nanotube growth by alcohol catalytic chemical vapor deposition method
Published 2007“…Three types of heat-treatment, synthesis of 30 min, synthesis of 30 min after annealing of 30 min, and synthesis of 60 min, were investigated. …”
Get full text
Article -
219
Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
Published 2013“…The highest MRR of 9.93mg/min was obtained with the current of 6.5A and pulse duration of 7.5 μs. …”
Get full text
Get full text
Get full text
Proceeding Paper -
220