-
701
Damage intensity class for reinforced concrete beam-column joint subjected to lateral cyclic loading
Published 2021“…These damages were caused by lack of shear links confinement and insufficient anchorage length, particularly on the RC beam-column joint (BCJ) of the buildings. …”
Get full text
Thesis -
702
Silicon carbide powder mixed micro electro discharge milling of titanium alloy
Published 2011“…A multi criteria optimization on low Ra, high MRR and low EWR has been achieved which showed 2.68 µm Ra., 6.908 µg/min MRR and 1.518 µg/min EWRfor the input parameters of 15.42 g/l SiC powder concentration and 54.28 µJ discharge energy. …”
Get full text
Article -
703
Optimization of the conditions for extraction of serine protease from Kesinai plant (Streblus asper) leaves using Response Surface Methodology
Published 2011“…The most desirable conditions of 2.5 °C temperature, 4 min mixing time, 40 mL buffer at pH 7.5 was established for serine protease extraction from kesinai leaves.…”
Get full text
Article -
704
Investigation of vibration and surface roughness in micro milling of PMMA
Published 2012“…The optimum solution for minimum average vibration is 64.3 Hz with spindle speed 3000 rpm, feed rate 2 mm/min, and depth of cut 1.5 μm. However, the optimum solution for minimum average surface roughness, Ra is 0.352 μm with spindle speed 2000 rpm, feed rate 2 mm/min, and depth of cut 1.5 μm. …”
Get full text
Article -
705
Acid blue 25 adsorption on base treated Shorea dasyphylla sawdust: kinetic, isotherm, thermodynamic and spectroscopic analysis
Published 2012“…The optimum conditions for AB 25 adsorption were pH 2, stirring rate 500 r/min, adsorbent dosage 0.10 g and contact time 60 min. …”
Get full text
Article -
706
Treatment of biotreated palm oil mill effluent using powdered activated carbon produced from palm empty fruit bunch
Published 2013“…Powdered Activated Carbon (PAC) was produced from empty fruit bunch (EFB) precursors by CO2 activation at 800¬0C, N2 (2.5 L/min) for 30 mins and CO2 (0.1L/min) for 15 mins. …”
Get full text
Proceeding Paper -
707
Capabilities of cermets tools for high speed machining of austenitic stainless steel
Published 2006“…In the present work cermet tools coated with titanium nitride were used to turn austenitic stainless steel at speeds between 300 and 700 m min-1. Feed rates were varied between 0.05 to 0.4 mm rev-1. …”
Get full text
Article -
708
Pembangunan video dokumentari pendidikan bagi mata pelajaran teknologi konkrit
Published 2004“…The data was analyzed using statistic method from Statistical Packages for Social Sciences (SPSS) version 11.0 which include percentages, min score and standard devition. Research result are positif that is the min score for each item from section B exceeding 3.8. …”
Get full text
Get full text
Get full text
Thesis -
709
Rare presentation of burholderia psedomallei infection
Published 2007Get full text
Proceeding Paper -
710
Hierarchical Tori Connected Mesh Network
Published 2013“…It is shown that the HTM possesses several attractive features, including constant node degree, small diameter, low cost, small average distance, moderate (neither too low, nor too high) bisection width, small wiring complexity, and high throughput per link and very low zero load latency, which provide better dynamic communication performance than that of H3DM, mesh, and torus networks.…”
Get full text
Book Chapter -
711
-
712
Management accounting and risk management in Malaysian financial institutions : an exploratory study
Published 2011“…Purpose – The purpose of this paper is to examine the link between management accounting and risk management. …”
Get full text
Article -
713
-
714
-
715
Mrs Dalloway and the finite transcendental: existence, time and transcendence in Woolf, Husserl and Derrida
Published 1999“…This chapter explores the link between Virginia Woolf, Edmund Husserl and Jacques Derrida.…”
Get full text
Book Section -
716
The production of carbon nanotubes using two-stage chemical vapor deposition and their potential use in protein purification
Published 2011“…The statistical analysis reveals that the optimum conditions for the CNT production were reaction temperature of 850 ◦C, reaction time of 60 min and gases flow rates of 40 and 150 ml/min for C2H2 and H2, respectively. …”
Get full text
Article -
717
Extraction of Algae Oil from Nannocloropsis sp.: A study of Soxhlet and Ultrasonic-Assisted Extractions
Published 2011“…While in the DE study, 51.6 min, 98% of ethanol concentration and 69.62°C were the best circwnstance in which the quantity of the oil yield got its maximwn. …”
Get full text
Article -
718
Inhalable and respirable dust from coal-fired power plant
Published 2015“…Coal-fired power plant emission had been recognized as one of the manmade sources of particulate matter. 8-hours personal particulate matter sampling had been done at a coal-fired power plant with 7-hole sampler at 2 L/min air flow and cyclone sampler at 2.2 L/min air flow. …”
Get full text
Article -
719
Cloning and expression of a novel phytase gene (phyMS) from Mycobacterium smegmatis
Published 2014“…The purified enzyme retains almost 30% of the initial activity after incubation at 90˚C for 60 min. The enzyme showed broad substrate specificity with Km and Vmax of the recombinant enzyme for sodium phytate substrate of 0.105 ± 0.016 mM and 26.93 ± 1.21 mM min−1, respectively.…”
Get full text
Article -
720
Enhanced settleability and dewaterability of fungal treated domestic wastewater sludge by liquid state bioconversion process
Published 2003“…The settling rate (measured as total suspended solids (TSS) concentration, 130 mg/l) was faster in treated sludge than untreated sludge (TSS concentration, 440 mg/l) after 1 min of settling time. In 1 min of settling operation, 86.45% of TSS was settled in treated sludge while 4.35% of TSS settled in raw sludge. …”
Get full text
Article